These Listings were Last Updated on Saturday, November 07, 2009 at 4:15 AM Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.

Warning: NSF is concerned about fraudulent downloading and manipulation of website text. If you have received this listing in hard copy, always confirm this certification/listing information by going directly to http://www.nsf.org/Certified/Food_Processing/Listings.asp? for the latest most accurate information.

[4] Maximum end use temperature of 900°F.

[3] Maximum end use temperature of 1500°F.

[5] Maximum end use temperature of 450°F.

[5] Maximum end use temperature of 450°F.

[2] Maximum end use temperature of 700°F.

[3] Maximum end use temperature of 1500°F.

[2] Maximum end use temperature of 700°F.

[4] Maximum end use temperature of 900°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[5] Maximum end use temperature of 450°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[5] Maximum end use temperature of 450°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[1] Non-stick and release coatings for use in meat and poultry processing.
    Accepted for direct food contact.

[4] Maximum end use temperature of 900°F.

[3] Maximum end use temperature of 1500°F.

[5] Maximum end use temperature of 450°F.

[5] Maximum end use temperature of 450°F.

[2] Maximum end use temperature of 700°F.

[3] Maximum end use temperature of 1500°F.

[2] Maximum end use temperature of 700°F.

[4] Maximum end use temperature of 900°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[5] Maximum end use temperature of 450°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[5] Maximum end use temperature of 450°F.

[2] Maximum end use temperature of 700°F.

[2] Maximum end use temperature of 700°F.

[1] Non-stick and release coatings for use in meat and poultry processing.
    Accepted for direct food contact.

[1] NSF Certified models have suffix N.
[2] Available with optional stainless steel outfeed tray.

[1] Low NOX models available.

[1] 8th position of model number identifies: (S) Single Tower, (T) Twin Tower.
    9th position of model number identifies type of emission: (L) Low Nox, (R) Regular.
    10th and 11th positions of model number identify type of burner: (MX) Maxon,
      (AC) American Combustion, (WB) Webster, (EC) Eclipse.
    12th position of model number indicates fuel type: (N) Natural Gas, (P) Propane.
    13th and 14th positions of model number identify the revision number.
    
    Further numeric values in the model number will indicate BTU/HR ratings.
    Model 00600-0800 will have BTU/HR ratings from 600,000 to 8,000,000 respectively.
    Models 1000-7000 will have BTU/HR ratings from 10,000,000 to 70,000,000 respectively.
[2] Units also Certified for performance against the requirements of NSF Standard 5.

[1] Model is available with or without the following options: Cutting board, side guard,
    belt lifter, scraper.

[1] May have the following suffixes:
    B   - Optional mounting base.  Valid values are B and blank.
    ##  - Gear ratio.  A ratio is required.  Valid values are 5,10, 15, 20, 25, 30, 40, 50, 
          60, and 80.
    K   - Indicates the unit is filled with synthetic food grade lubricant.  Blank means 
          the unit has no lubricant.  Valid valued are K and blank.
    MM  - Motor mounting.  A motor mounting is required.  Valid values are B5, B7, and B9.
    SS  - Shaft style.  A shaft style is required.  Valid values are GS, HS, and JS.
    PPP - Shaft bore designation.  Required for any SSH type unit.  Valid values are P12, 
          P14, P15, P16, P17, P18, P19, P20, P21, P22, P23, P24, P26, P27, P28, P30, P31, 
          P32, and P35.
    X   - Optional mounting position designation.  Valid values are 1, 2, 3, 4, 5, 6, 
          and blank.

[2] (1) indicates bore size in inches.
[3] Available in beige and natural polyamide and natural polyoxymethylene.

[1] Availabe in blue, natural, and white polyoxymethylene; blue, natural, and white
    polypropylene; and blue and natural polyethylene.

[1] Available in blue acetyl, natural acetyl, white polypropylene, gray polypropylene, blue
    polypropylene, white polyethylene, blue polyethylene, gray nylon, and white nylon.
[2] Available in blue acetyl and blue polypropylene.

[1] Available in cobalt blue and white.

[2] (1) Number of teeth
    (2) Bore size
[3] Available in natural.
[4] May or may not have suffix N1 or N2.

[2] (1) Number of teeth
    (2) Bore size
[3] Available in natural.
[4] May or may not have suffix N1 or N2.

[1] (1) Belt material
        DI   - Acetyl Copolymer
        PA66 - Polyamide
        PEI  - Polyethylene
        PEMI - Metal Detectable Polyethylene
        PP   - Polypropylene
        PPMI - Metal Detectable Polypropylene
        PVDF - Polyvinylidenflouride
    (2) Pin material
        PA66 - Polyamide
        PE   - Polyethylene
        PEMI - Metal Detectable Polyethylene
        PP   - Polypropylene
        PPMI - Metal Detectable Polypropylene
        PVDF - Polyvinylidenflouride
    (3) Percent surface opening (not present if width is shown) - 00, or width 
        (not present if opening is shown) - K1800, K2000, K2400
    (4) Color
        B     - Blue
        DB    - Blue
        DD    - Red
        G     - Grey
        N     - Natural
        UV    - UV stablized		
        W     - White  
        WH    - White
        WHITE - White