NSF Certified Products - Public Water Supply System Components

These NSF Official Listings are current as of Sunday, February 03, 2013 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://www.nsf.org/Certified/PwsComponents/Listings.asp?

NSF/ANSI STANDARD 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings.

3M / Infrastructure Protection Division
3M Center, Building 201-2C-11
St. Paul, MN 55144
United States
651-736-9030
Visit this company's website

Facility : Minnetonka, MN

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	ScotchKote 323[1]	>= 2"	CLD 23	EPOXY
	Scotchkote 323C[1]	>= 2"	CLD 23	EPOXY
	Scotchkote 323P[1]	>- 2"	CLD 23	EPOXY
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 30 Maximum Thinner: None Final Cure Time and Temperature: 120°F for 2 hours Special Comments: Mix ratio of A:B is 2:1 by volume.
Coatings - Pipe
	ScotchKote 323[1]	>= 2"	CLD 23	EPOXY
	Scotchkote 323C[1]	>= 2"	CLD 23	EPOXY
	Scotchkote 323P[1]	>= 2"	CLD 23	EPOXY
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 30 Maximum Thinner: None Final Cure Time and Temperature: 120°F for 2 hours Special Comments: Mix ratio of A:B is 2:1 by volume.
Coatings - Tank
	ScotchKote 323[1]	>= 50 gal.	CLD 23	EPOXY
	Scotchkote 323C[1]	>= 50 gal.	CLD 23	EPOXY
	Scotchkote 323P[1]	>= 50 gal.	CLD 23	EPOXY
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 30 Maximum Thinner: None Final Cure Time and Temperature: 120°F for 2 hours Special Comments: Mix ratio of A:B is 2:1 by volume.
Coatings - Valve
	ScotchKote 323[1]	>= 2"	CLD 23	EPOXY
	Scotchkote 323C[1]	>= 2"	CLD 23	EPOXY
	Scotchkote 323P[1]	>= 2"	CLD 23	EPOXY
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 30 Maximum Thinner: None Final Cure Time and Temperature: 120°F for 2 hours Special Comments: Mix ratio of A:B is 2:1 by volume.

Facility : Angleton, TX

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 8G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1]	>= 1/2"	D. HOT	PEC
	ScotchKote 134[2]	>= 1/2"	D. HOT	PEC
	ScotchKote 134W[2]	>= 1/2"	D. HOT	PEC
	Scotchkote 206N[3]	>= 4"	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 4"	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 4"	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 4"	D. HOT	PEC
[1] Colors: Dark Green Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 50 Maximum thinner: None Final Cure Time and Temperature: 6233 4G/2621 4G: 40 seconds at 450° F; 6233 8G/2621 8G: 90 seconds at 450° F; 6233 11G/2621 11G: 110 seconds at 450° F Special Comments: Preheat part to 425° - 488° F before application of powder. [2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425°F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400°F
Coatings - Pipe
	ScotchKote 134[2]	>= 1/2"	D. HOT	PEC
	ScotchKote 134W[2]	>= 1/2"	D. HOT	PEC
	Scotchkote 206N[3]	>= 4"	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 4"	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 4'	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 4"	D. HOT	PEC
[2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425°F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400°F
Coatings - Pump
	ScotchKote 134[2]	[4]	D. HOT	PEC
	ScotchKote 134W[2]	[4]	D. HOT	PEC
	Scotchkote 206N[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 2"[4]	D. HOT	PEC
[2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425°F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400°F [4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end use.
Coatings - Tank
	ScotchKote 134[2]	>= 5 gal.	D. HOT	PEC
	ScotchKote 134W[2]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N[3] [4]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N Extra LG[3] [4]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3] [4]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N Long Gel[3] [4]	>= 5 gal.	D. HOT	PEC
[2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425°F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400°F [4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end use.
Coatings - Valve
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 8G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1]	>= 1/2"	D. HOT	PEC
	ScotchKote 134[2]	>= 1/2"	D. HOT	PEC
	ScotchKote 134W[2]	>= 1/2"	D. HOT	PEC
	Scotchkote 206N[3]	>= 2"	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 2"	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 2"	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 2"	D. HOT	PEC
[1] Colors: Dark Green Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 50 Maximum thinner: None Final Cure Time and Temperature: 6233 4G/2621 4G: 40 seconds at 450° F; 6233 8G/2621 8G: 90 seconds at 450° F; 6233 11G/2621 11G: 110 seconds at 450° F Special Comments: Preheat part to 425° - 488° F before application of powder. [2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425°F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400°F

Facility : Morden, Manitoba, Canada

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 8G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1]	>= 1/2"	D. HOT	PEC
	ScotchKote 134[2]	>= 1/2"[4]	D. HOT	PEC
	ScotchKote 134W[2]	>= 1/2"[4]	D. HOT	PEC
	Scotchkote 206N[3]	>= 4"[4]	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 4"[4]	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 4"[4]	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 4"[4]	D. HOT	PEC
[1] Colors: Dark Green Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 50 Maximum Thinner: None Final Cure Time and Temperature: 6233 4G/2621 4G: 40 seconds at 450° F; 6233 8G/2621 8G: 90 seconds at 450° F; 6233 11G/2621 11G: 110 seconds at 450° F Special Comments: Preheat part to 425° - 488° F before application of powder. [2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425° F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400° F [4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end use.
Coatings - Pipe
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 8G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1]	>= 1/2"	D. HOT	PEC
	ScotchKote 134[2]	>= 1/2"[4]	D. HOT	PEC
	ScotchKote 134W[2]	>= 1/2"[4]	D. HOT	PEC
	Scotchkote 206N[3]	>= 4"[4]	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 4"[4]	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 4"[4]	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 4"[4]	D. HOT	PEC
[1] Colors: Dark Green Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 50 Maximum Thinner: None Final Cure Time and Temperature: 6233 4G/2621 4G: 40 seconds at 450° F; 6233 8G/2621 8G: 90 seconds at 450° F; 6233 11G/2621 11G: 110 seconds at 450° F Special Comments: Preheat part to 425° - 488° F before application of powder. [2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425° F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400° F [4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end use.
Coatings - Pump
	ScotchKote 134[2]	[4]	D. HOT	PEC
	ScotchKote 134W[2]	[4]	D. HOT	PEC
	Scotchkote 206N[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 2"[4]	D. HOT	PEC
[2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425° F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400° F [4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end use.
Coatings - Tank
	ScotchKote 134[2]	>= 5 gal.	D. HOT	PEC
	ScotchKote 134W[2]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N[3] [4]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N Extra LG[3] [4]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3] [4]	>= 5 gal.	D. HOT	PEC
	Scotchkote 206N Long Gel[3] [4]	>= 5 gal.	D. HOT	PEC
[2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425° F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400° F [4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end use.
Coatings - Valve
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 2621 8G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1]	>= 1/2"	D. HOT	PEC
	3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1]	>= 1/2"	D. HOT	PEC
	ScotchKote 134[2]	>= 1/2"[4]	D. HOT	PEC
	ScotchKote 134W[2]	>= 1/2"[4]	D. HOT	PEC
	Scotchkote 206N[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Extra LG[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Fluid Bed[3]	>= 2"[4]	D. HOT	PEC
	Scotchkote 206N Long Gel[3]	>= 2"[4]	D. HOT	PEC
[1] Colors: Dark Green Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 50 Maximum Thinner: None Final Cure Time and Temperature: 6233 4G/2621 4G: 40 seconds at 450° F; 6233 8G/2621 8G: 90 seconds at 450° F; 6233 11G/2621 11G: 110 seconds at 450° F Special Comments: Preheat part to 425° - 488° F before application of powder. [2] Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Final Cure Time and Temperature: 25 minutes at 425° F [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 60 Final Cure Time and Temperature: 180 seconds at 400° F [4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end use.

Facility : North Yorkshire, United Kingdom

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	Scotchkote 162PWX[1]	>= 4"	CLD 23	EPOXY
[1] Colors: Blue or gray Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 40 Final Cure Time and Temperature: 7 days at 20°C Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior to being placed into service.
Coatings - Pipe - Immediate Return to Service
	3M Scotchkote Pipe Renewal Liner 2400[2] [3]	>= 4"	CLD 23	PUA
	Scotchkote 162PWX[1] [2]	>= 1"	CLD 23	EPOXY
[1] Colors: Blue or gray Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 40 Final Cure Time and Temperature: 7 days at 20°C Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior to being placed into service. [2] Evaluated for Immediate Return to Service. [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 473 Maximum Thinner: None Final Cure Time and Temperature: 1 hour at 3°C (37°F) Special Comments: Mix ratio of Base:Activator is 1:1 by volume. No disinfection step required. Flush for 30 minutes at 5 gallons/minute. Certified for dry film thickness (DFT) of 40-473 mils
Coatings - Tank
	Scotchkote 162PWX[1] [2]	>= 100 gal.	CLD 23	EPOXY
[1] Colors: Blue or gray Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 40 Final Cure Time and Temperature: 7 days at 20°C Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior to being placed into service. [2] Evaluated for Immediate Return to Service.
Coatings - Valve
	Scotchkote 162PWX[1] [2]	>= 4"	CLD 23	EPOXY
[1] Colors: Blue or gray Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 40 Final Cure Time and Temperature: 7 days at 20°C Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior to being placed into service. [2] Evaluated for Immediate Return to Service.

NOTE: Only products bearing the NSF Mark are NSF Certified.

3M Purification Inc. (formerly Cuno, Incorporated)
400 Research Parkway
Meriden, CT 06450
United States
651-733-0587
Visit this company's website

Facility : Juarez, Chihuahua, Mexico

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Microfiltration Devices [G]
	742B[2]	[1]	CLD 23	MLTPL
	742B30[2]	[1]	CLD 23	MLTPL
	743B[2]	[1]	CLD 23	MLTPL
	743B30[2]	[1]	CLD 23	MLTPL
	743KF[2]	[1]	CLD 23	MLTPL
	744B[2]	[1]	CLD 23	MLTPL
	744B30[2]	[1]	CLD 23	MLTPL
	744KF[2]	[1]	CLD 23	MLTPL
	745B[2]	[1]	CLD 23	MLTPL
	745B30[2]	[1]	CLD 23	MLTPL
	745KF[2]	[1]	CLD 23	MLTPL
	746B[2]	[1]	CLD 23	MLTPL
	746B30[2]	[1]	CLD 23	MLTPL
	746KF[2]	[1]	CLD 23	MLTPL
	Cuno High Flow Filter Element (HF-WW-PP-XXX-Y-Z)[3]	[4]	CLD 23	MLTPL
[1] Certified for a minimum flow rate of 55,000 L/day. Dimensions: B30 units - 28.75" long, 6.5" outer diameter, and 1.6" inner diameter. B units - 39" long, 6.5" outer diameter, and 1.6" inner diameter. KF units - 39" long, 6.5" outer diameter, and 1.6" inner diamter. [2] Product codes: 742 - 1 micron 743 - 2 micron 744 - 5 micron 745 - 10 micron 746 - 15 micron [3] WW - Length of cartridge, in inches 40 60 XXX - Removal rating 001 - 1 micron 002 - 2 micron 005 - 5 micron 010 - 10 micron 015 - 15 micron 025 - 25 micron 040 - 40 micron 070 - 70 micron Y - End o-ring type A - Silicone B - Fluorocarbon C - EPR D - Nitrile Z - Packaging option (numbers of filters per box) 01 - 1 pack 04 - 4 pack Size: Filter elements are 40" or 60" long and 6.5" in diameter. [4] Certified for a minimum flow of 65,000 L/day. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.
NOTE: NSF has not conducted production control audits at this facility.  Product Listing is
      based on type testing [ISO/IEC Guide 2: 1996(E/F/R) 14.5].

7507852 Canada Inc. DBA Next Polymers
340 Churchill Road
Prescott, ON K0E 1T0
Canada
613-925-4281
Visit this company's website

Facility : Prescott, Ontario, Canada

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Pipe Only
	Aqualoc[1]	>= 1/2"	CLD 23	PVC
	Rehau Proloc[2]	>= 1/2"	CLD 23	PVC
[1] Certified for the following colors: blue, gray, and white. [2] Certified for the following colors: gray and white

A & D Technologies Incorporated
5BA-908, #765-7, Seonggok-dong
Ansan-shi, Kyungki-do
Korea, Republic of
82 31 319 8511

Facility : Kyungki-Do, Korea, Republic of

Mechanical Plumbing Devices

	Trade Designation
Ceramic Discs
	D20GT1-U,L (G180 DIS, G90 SUP)
	D20GT2 (G 90 INF)
	D20RS1-U,L (450020, 450019)
	D20RS2-U,L (450038, 450037)
	D20ST1-U,L (40257, 40278)
	D20ST2-U,L (40259, 40279)
	D25DL1-U,L (58030, 58031)
	D25GTF-L (G25F-CER-INF-GS)
	D25GTF-U (G25F-CER-SUP-APERTA)
	D25KC1-L (B6D)
	D25KC1-U (B6U)
	D25KC2-U (B12D)
	D25KC2-U (B12U)
	D25KM1-U,L (KAC2506, KAC2507)
	D25KM2-U,L (KAC2506P, KAC2507P)
	D25ST1-U,L (40263, 40264)
	D25ST2-U,L (40255, 40256)
	D25ST4-U,L (40299, 40251)
	D35DL1-U,L (58053, 58054)
	D35GT1-L (INF GM35)
	D35GT2-U (SUP GM35)
	D35HP1-U,L (dis N 131, dis N 130b)
	D35KC1-U,L (B1U, B1D)
	D35KC7-U,L (B7U, B7D)
	D35KC8-U,L (B8U, B8D)
	D35KM1-U,L (KAC3506, KAC3507)
	D35RS1-U (450018)
	D35ST1-L (40292)
	D35ST1-U (40291)
	D35ST2-L (41271)
	D35YJ1-U,L (35202-A, 35202-B)
	D40DL3-U,L (58045-1, 58046-1)
	D40GT1-L (INF G12)
	D40GT2-U (G12)
	D40GT3-L (INF-G16)
	D40KC11-U,L (G1U, G1D)
	D40KC13-U (B13D)
	D40KC13-U (B13U)
	D40KM1-U,L (KAC0006, KAC0007)
	D40RS2-U,L (450030, 450031)
	D40ST1-U,L (40265, 40266)

A. O. Smith Enterprises Ltd.
768 Erie Street
P.O. Box 310
Stratford, ON N5A 6T3
Canada
519-271-5800

Facility : Stratford, Ontario, Canada

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Pressurized Water Storage Tanks[1] [G]
	A O Smith ProMax	8.4 - 119 gal.	CLD 23	MLTPL
	AOS 25P	4.5 gal.	CLD 23	MLTPL
	Aqua-Air Water System Tanks (AOS Prefix)	8.4 - 70.5 gal.	CLD 23	MLTPL
	Bruiser Water System Tanks (BR Prefix)	>8.2 gal.	CLD 23	MLTPL
	Bruiser Water System Tanks (BR prefix)	2 - 4.5 gal.	CLD 23	MLTPL
	CentriPro T Water System Tanks	8.4 - 70.5 gal.	CLD 23	MLTPL
	CentriPro T Water System Tanks	1.2 - 4.5 gal.	CLD 23	MLTPL
	CentriPro TP Water System Tanks	1.2 - 70.5 gal.	CLD 23	MLTPL
	Enduro Water System Tanks (ET Prefix)	1.2 - 70.5 gal.	CLD 23	MLTPL
	GSW Waterguard	8.4 - 119 gal.	CLD 23	MLTPL
	Global Pump	>= 85 gal.	CLD 23	MLTPL
	Hydro Pro Water System Tanks (V Prefix)	1.2 - 70.5 gal.	CLD 23	MLTPL
	Hydro Pro Water System Tanks (V prefix and MP or PST suffix)	8.4 - 12.1 gal.	CLD 23	MLTPL
	John Wood	8.4 - 119 gal.	CLD 23	MLTPL
	Pump Pro (MP and PST Suffix)	>= 14 gal.	CLD 23	MLTPL
	Red Jacket Water System Tanks (ET prefix)	8.4 - 70.5 gal.	CLD 23	MLTPL
	Red Jacket Water System Tanks (RJT prefix)	8.4 - 70.5 gal.	CLD 23	MLTPL
	Red Jacket Water Systems (ET prefix)	2.7 - 4.5 gal.	CLD 23	MLTPL
	Red Jacket Water Systems (RJT prefix)	2.7 - 4.5 gal.	CLD 23	MLTPL
	Reliance	8.4 - 119 gal.	CLD 23	MLTPL
	Trident	>= 14 gal.	CLD 23	MLTPL
	Trident Ultra	>= 2 gal.	CLD 23	MLTPL
[1] Product also complies with NSF/ANSI 372. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
Thermal Expansion Tanks[1] [G]
	Bell and Gossett[2]	14 - 86 gal.	D. HOT	MLTPL
[1] Product also complies with NSF/ANSI 372. [2] Suffixes: blank B - Buried EX - Base extension MP - Mounted pump P - Pipe mounted PST - Pump system tank S [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

A. Schulman, Inc.
1183 Home Avenue
Akron, OH 44310
United States
800-532-7786
330-630-7103

Facility : Akron, OH

Potable Water Materials

			Water	Water
			Contact	Contact
	Trade Designation	End Use	Temp	Material
Potable Water Materials
	Aqualoy® 125B[1]	A,F	C. HOT	RPP
	Aqualoy® 125M Black[2]	A,F	C. HOT	RPP
	Aqualoy® 125M Natural[2]	A,F	C. HOT	RPP
	Aqualoy® 125N[1]	F	C. HOT	RPP
	Aqualoy® 135B[1]	A,F	C. HOT	RPP
	Aqualoy® 135W[2]	A,F	C. HOT	RPP
	Aqualoy® 140B[1]	F	C. HOT	RPP
	Aqualoy® 140W[1]	F	C. HOT	RPP
	Aqualoy® 145N[1]	F	C. HOT	RPP
	E-10025N[1]	F	C. HOT	RPP
	E-10026B[1]	A,F	C. HOT	RPP
[1] Certified for a maximum surface area to volume ratio of 1600 sq. in./L. [2] Certified for a maximum surface area to volume ratio of 250 sq. in./L.

A. W. Chesterton Co.
500 Unicorn Park Drive
Woburn, MA 01888-4004
United States
978-469-6766

Facility : Groveland, MA

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	ARC PW	>= 12"	CLD 23	EPOXY
Coatings - Pump
	ARC PW	>= 4"	CLD 23	EPOXY
Coatings - Valve
	ARC PW	>= 4"	CLD 23	EPOXY

[1] Colors: Light blue, white
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 30
    Recoat Cure Time and Temperature: 6 hours at 77°F  
    Final Cure Time and Temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 3:1 by weight or 2:1 by volume

A. W. Chesterton Co.
225 Fallon Road
P.O. Box 9101
Stoneham, MA 02180-9101
United States
617-438-7000

Facility : # 1 USA

Joining and Sealing Materials

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Patching Materials
	ARC 5ES	[1]	C. HOT	EPOXY
[1] The exposed surface area of each sealant in a household distribution system should not exceed 1.3 sq. cm/L or .2 sq. in/L.

A.U.K. Müller GmbH & Co. KG
Dresdener Str. 162
D-40595 Düsseldorf
Germany
49 21 173 910
Visit this company's website

Facility : Düsseldorf, Germany

Mechanical Plumbing Devices

	Trade Designation
Valves
	50.005.100 Cartridge Valve
	50.005.101 Cartridge valve
	50.007.806 Solenoid Cartridge Valve[1]
[1] Certified for models that include: G 1/2 male threads G 3/8 male threaded with G 3/8 female threads G 3/8 male threaded with G 1/2 female threads Model with sockets for customer provided fitting adapters.

A.Y. McDonald Mfg. Co.
4800 Chavenelle Road
Dubuque, IA 52004-0508
United States
800-292-2737

Facility : # 3 China

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Fittings
	2101P PEX Elbow (PEX x FPT, Drop Ear)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2300 PEX Coupling (PEX x PEX)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2300F PEX Adapter (PEX x FPT)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2300M PEX Adapter (PEX x MPT)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2300PB PEX Adapter, (PEX X PB) with Cramp Rings[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2300SF PEX Adapter (PEX x F Sweat)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2300SM PEX Adapter (PEX x M Sweat)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2301 PEX Adapter, Swivel (PEX x Closet) Plastic Nut[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2301 PEX Adapter, Swivel (PEX x NPSM) Plastic Nut[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2301B PEX Adapter, Swivel (PEX x FPT) Brass Nut[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2302 PEX Plug (PEX)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2330 PEX Tee (PEX Reducing)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2330 PEX Tee (PEX)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2330F PEX Tee (PEX x FPT)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2330M PEX Tee (PEX x MPT)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2390 PEX Elbow (PEX x PEX)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2391 PEX Elbow (PEX x MPT)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2392 PEX Elbow, Swivel (PEX x NPSM) Plastic Nut[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2392B PEX Elbow (Swivel) PEX x NPSM Brass nut)	3/8" - 1 1/4"	D. HOT	MLTPL
	2392B PEX Elbow, Swivel (PEX x NPSM) Brass Nut[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2392F PEX Elbow (PEX x F Sweat)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	2392M PEX Elbow (PEX x M Sweat)[1]	3/8" - 1 1/4"	D. HOT	MLTPL
	72101P PEX LF Drop Ear Elbow (PEX x FNPT)[3]	3/8" - 3/4"	D. HOT	MLTPL
	72300 PEX LF Coupling (PEX x PEX)[3]	3/8" - 1 1/4"	D. HOT	MLTPL
	72300F PEX LF Coupling (PEX x FNPT)[3]	1/2" - 1"	D. HOT	MLTPL
	72300M PEX LF Coupling (PEX x MNPT)[3]	3/8" - 1 1/4"	D. HOT	MLTPL
	72300PB PEX LF Coupling (PEX x PB)[3]	1/2" - 3/4"	D. HOT	MLTPL
	72300SF PEX LF Coupling (PEX x F Sweat)[3]	1/2" - 1"	D. HOT	MLTPL
	72300SFM PEX LF Adapter (PEX x Comb M-F Sweat)[3]	1/2" - 1"	D. HOT	MLTPL
	72300SM PEX LF Coupling (PEX x M Sweat)[3]	1/2" - 1 1/4"	D. HOT	MLTPL
	72301 PEX LF Swivel Adapter (PEX x FNPT – Plastic Nut)[3]	1/2"	D. HOT	MLTPL
	72301B PEX LF Swivel Adapter (PEX x FNPT – Brass Nut)[3]	1/2" - 3/4"	D. HOT	MLTPL
	72302 PEX LF Plug (PEX)[3]	3/8" - 1 1/4"	D. HOT	MLTPL
	72330 PEX LF Tee, Reducing Tee (PEX)[3]	1/2" - 1 1/4"	D. HOT	MLTPL
	72390 PEX LF Elbow (PEX)[3]	3/8" - 1 1/4"	D. HOT	MLTPL
	72391 PEX LF Elbow (PEX x MNPT)[3]	1/2" - 3/4"	D. HOT	MLTPL
	72392 PEX LF Swivel Elbow (PEX x NPSM - Plastic Nut)[3]	1/2"	D. HOT	MLTPL
	72392B PEX LF Swivel Elbow (PEX x NPSM - Brass Nut)[3]	1/2"	D. HOT	MLTPL
	72392F PEX LF Elbow (PEX x F Sweat)[3]	1/2" - 3/4"	D. HOT	MLTPL
	72392M PEX LF Elbow (PEX x M Sweat)[3]	1/2" - 3/4"	D. HOT	MLTPL
	Push Fit Fittings[1] [2]	3/8" - 1"	D. HOT	MLTPL
[1] Made with Linxalloy. [2] Tee (2301-XXXXXX) Coupling (2100-XXXX) Tee, reducing (2301-XXXXXX) Elbow (2190-XXXX) Elbow, Push Fit X MNPT, 1/2" x 1/2" only (2190M-0505) Elbow, Push Fit x FNPT, 1/2" x 1/2" (2190F-0505), 3/4" x 3/4" (2190F-0707) Adapter, Push Fit x MPT (2100M-XXXX) Adapter, Push Fit x FPT (2100F-XXXX) Drop Ear Elbow, Push Fit x FPT, 1/2" x 1/2", 3/8" x 1/2" only (2101Q-0505 and 2101Q-0405) Drop Ear Elbow, Push Fit x Push Fit, 1/2" x 1/2" only (2101QQ-0505) Test Cap (2103-XX) Each set of 'XX' may be 04 (3/8"), 05 (1/2"), 07 (3/4") or 08 (1") [3] Made with LF70.

Facility : Shanghai, China

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Fittings[G]
	2100A 1/2"	1/2"	D. HOT	MLTPL
	2100A 3/4"	3/4"	D. HOT	MLTPL
	2100A 3/4" x 1/2"	1/2" - 3/4"	D. HOT	MLTPL
	2100AM 1/2"	1/2"	D. HOT	MLTPL
	2100AM 3/4"	3/4'	D. HOT	MLTPL
	2100C Coupling - QC	1/2" - 1"	D. HOT	MLTPL
	2100CF Adatper - QC x FNPT	1/2" - 1"	D. HOT	MLTPL
	2100CM Adapter - QC x MNPT	1/2" - 1"	D. HOT	MLTPL
	2103A 1/2"	1/2"	D. HOT	MLTPL
	2103A 3/4"	3/4"	D. HOT	MLTPL
	2103C End Cap - QC	1/2" - 1"	D. HOT	MLTPL
	2130A 1/2"	1/2"	D. HOT	MLTPL
	2130A 3/4"	3/4"	D. HOT	MLTPL
	2130A 3/4" x 1/2"	1/2" - 3/4"	D. HOT	MLTPL
	2130C Tee - QC	1/2" - 1"	D. HOT	MLTPL
	2190A 1/2"	1/2"	D. HOT	MLTPL
	2190A 3/4"	3/4"	D. HOT	MLTPL
	2190C Elbow - QC	1/2" - 1"	D. HOT	MLTPL
	2190CF Elbow - QC x FNPT	1/2"	D. HOT	MLTPL
	2190CM Eblow - QC x MNPT	1/2"	D. HOT	MLTPL
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

A.Y. McDonald Mfg. Co.
4800 Chavenelle Road
Dubuque, IA 52004-0508
United States
800-292-2737

Facility : # 1 Taiwan

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Valves
	2062	1/2" - 1"	C. HOT	MLTPL

ABB Ltd.
Oldends Lane
Stonehouse, Glos
GL10 3TA
United Kingdom
44 14 5382 6661

Facility : Glos, United Kingdom

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Water Meters
	AM-F[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	AM-F[1]	3/4" - 3"	CLD 23	MLTPL
	AM-FC[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	AM-FC[1]	3/4" - 3"	CLD 23	MLTPL
	AM-R[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	AM-R[1]	3/4" - 3"	CLD 23	MLTPL
	AM-S[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	AM-S[1]	3/4" - 3"	CLD 23	MLTPL
	Aquamaster[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	Aquamaster[1]	3/4" - 3"	CLD 23	MLTPL
	Aquamaster F[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	Aquamaster F[1]	3/4" - 3"	CLD 23	MLTPL
	Aquamaster FC[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	Aquamaster FC[1]	3/4" - 3"	CLD 23	MLTPL
	Aquamaster R[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	Aquamaster R[1]	3/4" - 3"	CLD 23	MLTPL
	Aquamaster S[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	Aquamaster S[1]	3/4" - 3"	CLD 23	MLTPL
	FEF[G]	250 mm - 2400 mm	CLD 23	MLTPL
	FEV[G]	40 mm - 300 mm	CLD 23	MLTPL
	Magmaster[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	Magmaster[1]	3/4" - 3"	CLD 23	MLTPL
	Magmaster Loflo[1] [G]	>= 2 1/2"	CLD 23	MLTPL
	Magmaster Loflo[1]	3/4" - 3"	CLD 23	MLTPL
	WaterMaster F[G]	250 mm - 2400 mm	CLD 23	MLTPL
	WaterMaster V[G]	40 mm - 300 mm	CLD 23	MLTPL
[1] All Aquamaster and Magmaster models in sizes 4" - 95" (DN100 - DN2400) and the WaterMaster F (all sizes) may be chlorobutyl-lined. Magmaster models in sizes 2 1/2" (DN65) and 3" (DN80) may also be chlorobutyl-lined. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

NOTE: Only products bearing the NSF Mark are Certified.

ABSFIL Ltd.
#858 Jangdeok-dong
Hwaseong-si, Gyeonggi-do 445-130
Korea, Republic of
82 31 355 6166
Visit this company's website

Facility : Gyeonggi-do, Korea

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Filtration Devices/Components
	PRE III-Y-Z	[1]	CLD 23	PP
[1] Certified for a minimum flow rate of 6840 liters per day in water treatment facilities only. Certification does not include inner core, adapters, o-rings, gaskets, or end caps. Y - Micron rating (um) 0.5 - 100 Z - Length (in) 5 - 50

Access-Able Technologies, Inc.
1275 Bennett Drive
Suite #115
Longwood, FL 32750
United States
800-572-4894

Facility : # 1 USA

Joining and Sealing Materials

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Patching Materials [G]
	Pow-R Stick Steel Hard Epoxy Putty (Grey Color)	[1] [2]	C. HOT	EPOXY
	Pow-R Stick Steel Hard Epoxy Putty (Copper Color)	[1] [2]	C. HOT	EPOXY
	Pow-R Stick Steel Hard Epoxy Putty (White Color)	[1] [2]	C. HOT	EPOXY
	STIC-O-STEEL POW-R Putty	[1] [2]	C. HOT	EPOXY
[1] Certified for a maximum surface area to volume ratio not to exceed 0.3 sq. in./L in pipe or 1% of a 20,000 gallon tank. [2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full stick, of product which has been cut with a knife. Product must be mixed for 60-90 seconds. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Accor Technology Inc.
1400 - 112th Avenue South East
Suite 100
Bellevue, WA 98004
United States
800-447-5848
509-662-0608

Facility : East Wenatchee, WA

Mechanical Plumbing Devices

	Trade Designation
Connector Hoses
Riser Assemblies[1]
	R-5CP(1)-7(2)
	R-5CS(1)-7(2)
	R-5LP(1)-5(2)
	R-5LS(1)-5(2)
	R-CP(1)-7(2)
	R-CS(1)-7(2)
	R-LP(1)-3(2)
	R-LP(1)-5(2)
	R-LS(1)-3(2)
	R-LS(1)-5(2)
	R2-IP(1)-2(2)
	R3-LP(1)-3(2)
	RCP45T12-7(2)
[1] (1) Hose length (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
Supply Stops
Coupling w/ attached riser[1]
	PR30-LP(1)-3(2)
	PR30-SP(1)-3(2)
	PR50-CP(1)-7(2)
	PR50-CS(1)-7(2)
	PR50-LP(1)-3(2)
	PR50-LP(1)-5(2)
	PR50-LS(1)-3(2)
	PR50-LS(1)-5(2)
	PR50-P(1)-RK(2)
	PR50-S(1)-RK(2)
	PR50-SP(1)-5(2)
[1] (1) Hose length (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
Valve or Coupling[1]
	PO5-2(2)
	PO5-3(2)
	PO5-CAP(2)
	PR-30(2)
	PR-50(2)
	TH5-3(2)
[1] (1) Hose length (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
Valve w/ attached riser[1]
	PO5-CP(1)-7(2)
	PO5-CS(1)-7(2)
	PO5-IP(1)-2(2)
	PO5-LP(1)-3(2)
	PO5-LP(1)-5(2)
	PO5-LP4T15-5(2)
	PO5-LS(1)-3(2)
	PO5-LS(1)-5(2)
	PO5-LS4T15-5(2)
	PO5-P(1)-RK(2)
	PO5-P-PR30(2)
	PO5-S(1)-RK(2)
	PO5-S-PR30(2)
	PO5P10T10RK(2)
[1] (1) Hose length (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)

Accuflex Industrial Hose Ltd.
760 Imperial Road North
Guelph, ON N1K 1Z3
Canada
519-836-5460
Visit this company's website

Facility : Guelph, Ontario, Canada

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Tubing/Hose [G]
	Bev-Flex® 172	1/4" - 1"	CLD 23	PE
	Bev-Flex® 272	1/4" - 1"	CLD 23	PE
	Bev-Seal® 176	1/4" - 1"	CLD 23	PE
	Bev-Seal® 228	1/4" - 1"	CLD 23	PE
	Bev-Seal® Ultra 175	3/16" - 1"	CLD 23	PET
	Bev-Seal® Ultra 235	3/16" - 1"	CLD 23	PET
	Bev-Steel® 178	3/16" - 1"	CLD 23	PET
	Bevlex® 170	1/4" - 1"	CLD 23	PE
	Bevlex® 174	1/4" - 1"	CLD 23	PE
	Bevlex® 222	1/4" - 1"	CLD 23	PE
	Bevlex® 222YYY[1]	1/4" - 1"	CLD 23	PE
	Bevlex® 224	1/4" - 1"	CLD 23	PE
	Bevlex® Plus 180	3/16" - 1"	CLD 23	PET
	Bevlex® Plus 230	3/16" - 1"	CLD 23	PET
	Kuri Tec® A3236	1/4" - 1"	CLD 23	PE
	Kuri Tec® A3246	1/4" - 1"	CLD 23	PE
[1] YYY denotes color for the outermost layer. Color codes are: BLK - Black BLU - Blue DGRY - Dark Gray GRN - Green LGRY - Light Gray RED - Red WHT - White [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Ace Duraflo Systems, LLC
3122 West Alpine Street
Santa Ana, CA 92704
United States
714-256-0220
Visit this company's website

Facility : # 1 USA

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Pipe - Immediate Return to Service
	ADF 204[1] [2]	>= 1/2"	C. HOT	EPOXY
	ePIPE FRS[1] [3]	>= 1/2"	D. HOT	EPOXY
	ePipe®[1] [2]	>= 1/2"	C. HOT	EPOXY
[1] Evaluated for Immediate Return to Service. [2] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 10 Final Cure Time and Temperature: 24 hours at 77°F Special Comments: Mix ratio of A:B is 69.5:100 by weight. Induction time is 15 minutes. Product requires a one hour flush at 140°F prior to being placed into service. Product must be preconditioned for 24 hours at 100°F. Cold water (23°C) and D.HOT water (60°C) applications may be flushed for one hour at 120°F prior to be placed into service. [3] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 10 Final Cure Time and Temperature: Cure with air at minimum temperature of 85°F for 2 hours; then cure with tap water at service water temperature at flow rate of 1 gpm for 15 minutes. Special Comments: Mix ratio of A:B is 2:1 by volume. Bring material to 95°F before mixing.

Ace Hardware Corporation
2200 Kensington Court
Oak Brook, IL 60523-2100
United States
630-990-6441

Facility : Zhejiang, China

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Flexible Plumbing Connectors
	Brass Braided Faucet Supply Lines[1]	1/4" - 7/8"	D. HOT	MLTPL
	Brass Braided Toilet Supply Lines[1]	1/4" - 7/8"	D. HOT	MLTPL
	Corrugated Copper Water Heater Connectors[3]	3/4"	D. HOT	MLTPL
	Corrugated Stainless Steel Water Heater Connectors[2]	3/4"	D. HOT	MLTPL
	Reinforced Vinyl Faucet Supply Lines[1]	1/4" - 7/8"	D. HOT	MLTPL
	Reinforced Vinyl Toilet Supply Lines[1]	1/4" - 7/8"	D. HOT	MLTPL
	Stainless Steel Faucet Supply Lines[1]	1/4" - 7/8"	D. HOT	MLTPL
	Stainless Steel Toilet Supply Lines[1]	1/4" - 7/8"	D. HOT	MLTPL
[1] Certification includes all sizes less than 30 inches in length. [2] Connectors come in 12, 15, 18, and 24 inch lengths. [3] Certified for lengths between 12 and 24 inches, and connectors with fittings designed to attach PEX material.

Ace Hardware Corporation
2200 Kensington Court
Oak Brook, IL 60523-2100
United States
630-990-6441

Facility : Zheijiang, China

Mechanical Plumbing Devices

	Trade Designation
Flexible Plumbing Connectors[1]
Reinforced Vinyl Dishwasher Supply Lines
	FS-CDC-P-CE
	FS-CDC-P-FE
	FS-CDC-S-CE
	FS-CDC-S-FE
Reinforced Vinyl Faucet Supply Lines
	FS-CFC-P-CC
	FS-CFC-P-CF
	FS-CFC-P-CO
	FS-CFC-P-FF
	FS-CFC-P-TF
	FS-CFC-S-CC
	FS-CFC-S-CF
	FS-CFC-S-CO
	FS-CFC-S-FF
	FS-CFC-S-TF
Reinforced Vinyl Icemaker Supply Lines
	FS-CIC-P-CE
	FS-CIC-S-CE
Reinforced Vinyl Toilet Supply Lines
	FS-CTC-P-CB
	FS-CTC-P-FB
	FS-CTC-P-TB
	FS-CTC-S-CB
	FS-CTC-S-FB
	FS-CTC-S-TB
[1] FS - FloodSafe CFC - Faucet connector CIC - Ice maker supply line CTC - Toilet connector P - Reinforced vinyl hose S - Stainless steel braid over reinforced vinyl hose Type of connection from supply (maximum inlet size 1/2"): C - Compression end fitting F - FIP end fitting T - Fine thread FIP end fitting Type of connection to fixture (maximum outlet size 7/8"): B - Ballcock end fitting C - Compression end fitting E - MIP elbow end fitting F - FIP end fitting O - OD compression end fitting
Supply Stops[2]
Dual Outlet Angle Stop
	389000X
	389015X
	389200X
	389300X
	389400X
	389415X
	88900X
	88901X
	89000X
	89001X
	89015X
	89020X
	89021X
	89030X
	89031X
	89100X
	89101X
	89120X
	89121X
	89200X
	89201X
	89215X
	89220X
	89221X
	89300X
	89400X
	89401X
	89415X
	89420X
	89421X
	89430X
	89438X
	89448X
	89501X
	89601X
	DV389400X
	DV389431X
	F89000X
	F89001X
	F89015X
	F89200X
	F89220X
	1/2" PEX x PEX Kwik Stop
	BV38900X
	BV38905X
	BV38940X
	BV38945X
	BV88900X
	BV88901X
	BV88925X
	BV89000X
	BV89001X
	BV89015X
	BV89030X
	BV89031X
	BV89120X
	BV891213
	BV89121X
	BV89131X
	BV89200X
	BV89201X
	BV89240X
	BV89241X
	BV89400X
	BV89401X
	BV89415X
	BV89430X
	BV89431X
	DV38941X
	DV38944X
[2] Suffix "X" 1 - Rough brass 3 - Chrome plated LK - Loose key stem PB - Polished brass SD - Screw driver stem WEL - With escutcheon and less compression nut

Ace Hardware Corporation "Oakbrook"
2200 Kensington Court
Oak Brook, IL 60521-9989
United States
630-990-6600

Facility : Shenzhen, China

Mechanical Plumbing Devices

	Trade Designation
Faucets
	4008744
	4008751
	4038097
	4038097
	4038105
	4038105
	4038113
	4038147
	4038667
	4100855
	4100863
	4100871
	4100889
	4171526
	4171922
	4171930
	4171955
	4171963
	4171989
	4172045
	4172185
	4172193
	4196234
	4202776
	4202784
	4239497
	4239505
	4265112
	4265112
	4265138
	4265153
	4265161
	4265179
	4265195
	4265476
	4265484
	4265492
	4265518
	4265526
	4265534
	4268546
	4268553
	4292504
	4292512
	4309076
	4309084
	4309092
	4309118
	4309126
	4309134
	4309142
	4309159
	4309167
	4309175
	4309183
	4309191
	4309209
	4309217
	4309225
	4309233
	4309241
	4309258
	4309266
	4309282
	4309290
	4309308
	4309316
	4309324
	4309332
	4309340
	4309365
	4309449
	4311932
	4311940
	4312070
	4312088
	4312096
	4312104
	4312112
	4312120
	4312161
	4312203
	4312260
	4312302
	44948
	45007
	45058
	45675
	45968
	46576
	46577
	48000
	48001
	48002
	48003
	48004
	48005
	48006
	48007
	48008
	48057
	48058
	48170
	48365
	48366
	48367
	48368
	48369
	48370
	49226
	49227

Ace Roto-Mold
Division of Den Hartog Industries Inc.
4010 Hospers Drive South
P.O. Box 425
Hospers, IA 51238-0425
United States
800-342-3408
712-752-8432
Visit this company's website

Facility : Hospers, IA

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Tanks[1] [2]
	ACT1000-LP Cistern Tank	1000 gal.	CLD 23	PE
	ACT1500-LP Cistern Tank	1500 gal.	CLD 23	PE
	ACT2000-LP Cistern Tank	2000 gal.	CLD 23	PE
	ACT2500-LP Cistern Tank	2500 gal.	CLD 23	PE
	VT0010-12 Vertical Polyethylene Storage Tank	10 gal.	CLD 23	PE
	VT0020-16 Vertical Polyethylene Storage Tank	20 gal.	CLD 23	PE
	VT0025-18 Vertical Polyethylene Storage Tank	25 gal.	CLD 23	PE
	VT0040-18 Vertical Polyethylene Storage Tank	40 gal.	CLD 23	PE
	VT0055-20 Vertical Polyethylene Storage Tank	55 gal.	CLD 23	PE
	VT0065-23 Vertical Polyethylene Storage Tank	65 gal.	CLD 23	PE
	VT0075-23 Vertical Polyethylene Storage Tank	75 gal.	CLD 23	PE
	VT0100-28 Vertical Polyethylene Storage Tank	100 gal.	CLD 23	PE
	VT0105-23 Vertical Polyethylene Storage Tank	100 gal.	CLD 23	PE
	VT0110-32 Vertical Polyethylene Storage Tank	110 gal.	CLD 23	PE
	VT0130-32 Vertical Polyethylene Storage Tank	130 gal.	CLD 23	PE
	VT0135-28 Vertical Polyethylene Storage Tank	135 gal.	CLD 23	PE
	VT0160-28 Vertical Polyethylene Storage Tank	160 gal.	CLD 23	PE
	VT0175-31 Vertical Polyethylene Storage Tank	160 gal.	CLD 23	PE
	VT0180-40 Vertical Polyethylene Storage Tank	180 gal.	CLD 23	PE
	VT0210-40 Vertical Polyethylene Storage Tank	210 gal.	CLD 23	PE
	VT0225-31 Vertical Polyethylene Storage Tank	225 gal.	CLD 23	PE
	VT0265-31 Vertical Polyethylene Storage Tank	265 gal.	CLD 23	PE
	VT0295-42 Vertical Polyethylene Storage Tank	2635 gal.	CLD 23	PE
	VT0300-35 Vertical Polyethylene Storage Tank	300 gal.	CLD 23	PE
	VT0300-42 Vertical Polyethylene Storage Tank	300 gal.	CLD 23	PE
	VT0405-52 Vertical Polyethylene Storage Tank	405 gal.	CLD 23	PE
	VT0420-42 Vertical Polyethylene Storage Tank	420 gal.	CLD 23	PE
	VT0425-42 Vertical Polyethylene Storage Tank	425 gal.	CLD 23	PE
	VT0500-52 Vertical Polyethylene Storage Tank	500 gal.	CLD 23	PE
	VT0505-46 Vertical Polyethylene Storage Tank	505 gal.	CLD 23	PE
	VT0550-52 Vertical Polyethylene Storage Tank	550 gal.	CLD 23	PE
	VT0600-46 Vertical Polyethylene Storage Tank	600 gal.	CLD 23	PE
	VT0625-64 Vertical Polyethylene Storage Tank	625 gal.	CLD 23	PE
	VT0800-46 Vertical Polyethylene Storage Tank	800 gal.	CLD 23	PE
	VT0850-54 Vertical Polyethylene Storage Tank	850 gal.	CLD 23	PE
	VT0900-46 Vertical Polyethylene Storage Tank	900 gal.	CLD 23	PE
	VT1000-64 Vertical Polyethylene Storage Tank	1000 gal.	CLD 23	PE
	VT1050-86 Vertical Polyethylene Storage Tank	1050 gal.	CLD 23	PE
	VT10500-2500 Vertical Polyethylene Storage Tank	10,500 gal.	CLD 23	PE
	VT10500-2800 Vertical Polyethylene Storage Tank	10,500 gal.	CLD 23	PE
	VT1200-64 Vertical Polyethylene Storage Tank	1200 gal.	CLD 23	PE
	VT12500-142 Vertical Polyethylene Storage Tank	12,500 gal.	CLD 23	PE
	VT1350-86 Vertical Polyethylene Storage Tank	1350 gal.	CLD 23	PE
	VT1500-64 Vertical Polyethylene Storage Tank	1500 gal.	CLD 23	PE
	VT1500-86 Vertical Polyethylene Storage Tank	1500 gal.	CLD 23	PE
	VT1525-64 Vertical Polyethylene Storage Tank	1525 gal.	CLD 23	PE
	VT1650-86 Vertical Polyethylene Storage Tank	1650 gal.	CLD 23	PE
	VT2000-64 Vertical Polyethylene Storage Tank	2000 gal.	CLD 23	PE
	VT2000-90 Vertical Polyethylene Storage Tank	2000 gal.	CLD 23	PE
	VT2050-86 Vertical Polyethylene Storage Tank	2050 gal.	CLD 23	PE
	VT2150-102 Vertical Polyethylene Storage Tank	2150 gal.	CLD 23	PE
	VT2500-90 Vertical Polyethylene Storage Tank	2500 gal.	CLD 23	PE
	VT3000-90 Vertical Polyethylene Storage Tank	3000 gal.	CLD 23	PE
	VT3100-102 Vertical Polyethylene Storage Tank	3100 gal.	CLD 23	PE
	VT3400-102 Vertical Polyethylene Storage Tank	3400 gal.	CLD 23	PE
	VT4000-96 Vertical Polyethylene Storage Tank	4000 gal.	CLD 23	PE
	VT4200-96 Vertical Polyethylene Storage Tank	4200 gal.	CLD 23	PE
	VT5000-102 Vertical Polyethylene Storage Tank	5000 gal.	CLD 23	PE
	VT5150-102 Vertical Polyethylene Storage Tank	5150 gal.	CLD 23	PE
	VT6250-102 Vertical Polyethylene Storage Tank	6250 gal.	CLD 23	PE
	VT6500-120 Vertical Polyethylene Storage Tank	6500 gal.	CLD 23	PE
	VT7000-142 Vertical Polyethylene Storage Tank	7000 gal.	CLD 23	PE
	VT7800-120 Vertical Polyethylene Storage Tank	7800 gal.	CLD 23	PE
	VT8000-120 Vertical Polyethylene Storage Tank	8000 gal.	CLD 23	PE
	VT9150-120 Vertical Polyethylene Storage Tank	9150 gal.	CLD 23	PE
	VT9500-120 Vertical Polyethylene Storage Tank	9500 gal.	CLD 23	PE
[1] Certified for vertical tank (VT) shells that are black, blue, green, or natural. [2] Certified for cistern tank shells that are blue.

Aclo Compounders, a Business Unit of the Matrixx Group, Inc.
15000 Highway 41 North
Evansville, IN 47725
United States
519-653-5031

Facility : Guelph, Ontario, Canada

Potable Water Materials

			Water	Water
			Contact	Contact
	Trade Designation	End Use	Temp	Material
Material
	HPO 336 T40 002L A14625 Grey	P	CLD 23	RPP

AD Majoris S.A.S.
21 Rue Saint Jean
69550 Cublize
France
33 4 74 89 59 00
Visit this company's website

Facility : Cublize, France

Potable Water Materials

			Water	Water
			Contact	Contact
	Trade Designation	End Use	Temp	Material
Material
	MAJORIS G409/12.5 - 8229	A,F,P	D. HOT	RPP

ADA Carbon Solutions, LLC
8100 Southpark Way
Unit A-1
Littleton, CO 80120
United States
888-822-8617
303-962-1977
Visit this company's website

Facility : Coushatta, LA

Process Media

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Powdered Activated Carbon
	PowerPAC H20™ Plus[1] [2]	-325 mesh	CLD 23	PAC
	PowerPAC H2O™[1] [2]	-325 mesh	CLD 23	PAC
[1] Certified for a maximum use level of 250 mg/L. [2] The carbon source is lignite coal.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.

AdEdge Technologies, Inc.
5152 Belle Wood Court
Suites A
Burford, GA 30518
United States
678-835-0052

Facility : New Castle, DE

Process Media

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Oxidative Media
	AD26	[1]	CLD 23	MNDOX
[1] Certified for the following mesh sizes: 8 x 20, 20 x 40.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.

Facility : Quincy, IL

Process Media

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Oxidative Media
	AD26	[1]	CLD 23	MNDOX
[1] Certified for the following mesh sizes: 8 x 20, 20 x 40.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.

AdEdge Water Technologies, LLC
5152 Belle Wood Court
Buford, GA 30518
United States
866-823-3343
678-835-0052

Facility : #96476

Process Media

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Adsorption Media
	GFO PLUS	20 mesh - 200 mesh	CLD 23	-

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.

Adeka Corporation
7-2-35 Higashiogu
Arakawa-ku, Toyko, 116-8554
Japan
81 3 4455 2843
Visit this company's website

Facility : Ibaraki, Japan

Joining and Sealing Materials

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Gasket/Sealing Materials
	MC-2010MN	[1]	CLD 23	IR
[1] Certified for a maximum surface area to volume ratio not to exceed 0.13 sq. in./L.

Adhesive Technology Corp.
450 East Copans Road
Pompano Beach, FL 33064
United States
954-782-2221

Facility : WH09 USA

Joining and Sealing Materials

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Adhesives
	Ultrabond 365	[1]	CLD 23	ACR
[1] Certified for use at a maximum surface area to volume ratio of 0.0005 sq. in./L in a tank.

ADI International
1133 Regent Street, Suite 300
Fredericton, NB E3B 3Z2
Canada
800-858-1888
506-452-9000
Visit this company's website

Facility : Oshawa, Ontario, Canada

Process Media

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Filtration/Adsorption Media
	Media G2-R[2]	.4 - .7 mm	CLD 23	-
	Media G2®[1]	.08 - 1.25 mm	CLD 23	-
[1] Certification of this product is based on adherence to specific conditioning and rinsing protocol. [2] This product is to be rinsed with 200 bed volumes of water prior to initial start up. The Certification of this media is only for applications with a minimum flow rate greater than or equal to 3.4 gpm per cubic foot of resin.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.

Adolf Würth GmbH & Co. KG
Reinhold-Würth-Str. 12-17
Baden-Württemberg
74650 Künzelsau
Germany
49 7940 15 0

Facility : Fridolfing, Germany

Joining and Sealing Materials

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Sealants
	Acetatsilicon Lebensmittel	[1]	CLD 23	SLT
[1] Certified for a maximum surface area to volume ratio of 7.3 sq. in./L.

Adolf Würth GmbH & Co. KG
Produktmanagement Chemie, Postfach
74650 Künzelsau
Germany
49 794 015 2007

Facility : Wetzikon, Switzerland

Joining and Sealing Materials

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Adhesives
	Würth®saBesto DOS Schraubensicherung Hochfest	>= 1/2"	C. HOT	ADH
	Würth® saBesto DOS Schraubensicherung Mittelfest	>= 1/2"	C. HOT	ADH
	Würth® saBesto DOS Rohrdicht mit PTFE	>= 1/2"	C. HOT	ADH
Thread Compounds
	Würth® saBesto DOS Rohrdicht[1]	>= 1/2"	C. HOT	TC
	Würth®saBesto DOS Schraubensicherung Hochfest	>= 1/2"	C. HOT	TC
	Würth® saBesto DOS Rohrdicht mit PTFE	>= 1/2"	C. HOT	TC
[1] Certification is based on a minimum cure of 72 hours at 75°F.

Advance Products & Systems
207 Easy Street
Lafayette, LA 70596
United States
800-315-6009
337-233-6116
Visit this company's website

Facility : Lafayette, LA

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Dielectric Insulator[1]
	GLASSTEX 2000 / Trojan G-10 Flange Insulating Gasket Kit, Type ET	1/2" - 160"	D. HOT	MLTPL
	GLASSTEX 2000 / Trojan G-10 Flange Insulating Gasket Kit, Type FT	1/2" - 160"	D. HOT	MLTPL
[1] Certified for 1/8" thick flange insulating gaskets.

Advanced Component Services
1420 19th Avenue Northwest
Issaquah, WA 98027
United States
425-391-1572

Facility : Chang Hua, Taiwan

Mechanical Plumbing Devices

	Trade Designation
Faucets
Dispenser Series
	MET012
	MET012-B
	MET012-O
	MET127
	MET127-B
	MET127-O
	MET130(Low Lead Brass)
	MET130-RC
	MET133
	MET133(Low Lead Brass)
	MET133-OD
	MET133-R
	MET133-RW
	MET133-SBRH
	MET133-SBRH(Normal Brass)
	MET138
	MET138-OD
	MET138-R
	MET138-RW
	PLA131
	PLA131-OD
	PLA131-R
	PLA131-RW
Pre-Rinse Assembly Series[G]
	MET170-UN
	MET170-UNSG
	MET170-WN
	MET170-WNSG
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Advanced Technology Products
12740 State Route 4
P.O. Box 335
Milford Center, OH 43045
United States
937-349-4055
Visit this company's website

Facility : Milford Center, OH

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Tubing
	Imbibe™ LLDPE Tubing[1]	[2]	D. HOT	PE
[1] Certified for the following tubing colors: Black Blue Green Natural Red White Yellow [2] Certified for the following sizes: 1/4" - 1/2" 4 mm - 15 mm

AEI Compounds
Sandwich Industrial Estate
Sandwich
Kent CT13 9LY
United Kingdom
44 1474 566736

Facility : Kent, United Kingdom

Potable Water Materials

			Water	Water
			Contact	Contact
	Trade Designation	End Use	Temp	Material
Potable Water Materials
	SX734:CM488[1]	P	C. HOT	PEX
[1] Pipe manufactured of this material is cure process dependent. Use of this material in NSF Certified pipe requires NSF's prior authorization.

Aerator Solutions, LLC
11765 Main Street
Roscoe, IL 61073
United States
888-237-2867
815-623-5111
Visit this company's website

Facility : Roscoe, IL

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Miscellaneous Process Devices/Components
	EcoJet™ A10[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A15[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A20[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A25[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A3[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A30[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A40[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A5[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A50[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A60[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A7[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ A75[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M10[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M15[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M20[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M25[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M3[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M30[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M40[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M5[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M50[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M60[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M7[2] [G]	[1]	CLD 23	MLTPL
	EcoJet™ M75[2] [G]	[1]	CLD 23	MLTPL
[1] Certified for use in tanks 75,000 gallons and greater. [2] The "M" models are mixers while the "A" models are aerators. The numerical suffix after the "A" and "M" in the trade name indicate the horsepower of the motor. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

AGRU Kunststofftechnik GmbH
Ing. Pesendorfer Str. 31
A-4540 Bad Hall
Austria
43 7258 790 0
Visit this company's website

Facility : Bad Hall, Austria

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Ball Valves
	PE100/4710 Black Ball Valve	1/2" - 8"	CLD 23	MLTPL

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Fittings
	PE100/4710 black IPS E-Coupler	1/2" - 8"	CLD 23	PE
	PE100/4710 black IPS Elbow 45°	3/4" - 12"	CLD 23	PE
	PE100/4710 black IPS Elbow 90°	3/4" - 12"	CLD 23	PE
	PE100/4710 black IPS End Cap	3/4" - 12"	CLD 23	PE
	PE100/4710 black IPS Flange Adaptor	3/4" - 12"	CLD 23	PE
	PE100/4710 black IPS Reducer Concentric	2"x1 1/2" - 12"x10"	CLD 23	PE
	PE100/4710 black IPS Tee	3/4" - 12"	CLD 23	PE

Aignep SpA
Via G. Don Bazzoli, 34
25070 Bione (BS)
Italy
39 0365 896626
Visit this company's website

Facility : Bione (BS), Italy

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Fittings
	Food Grade Fittings 70010	4 mm - 8 mm	C. HOT	MLTPL
	Food Grade Fittings 70020	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70030	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70040	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70050	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70100	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70106	4 mm - 8 mm	C. HOT	MLTPL
	Food Grade Fittings 70116	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70126	4 mm - 10 mm	C. HOT	MLTPL
	Food Grade Fittings 70130	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70200	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70216	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70226	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70230	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70310	4 mm - 10 mm	C. HOT	MLTPL
	Food Grade Fittings 70500	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70505	4 mm - 6 mm	C. HOT	MLTPL
	Food Grade Fittings 70510	4 mm - 8 mm	C. HOT	MLTPL
	Food Grade Fittings 70550	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 70560	4 mm - 8 mm	C. HOT	MLTPL
	Food Grade Fittings 70700	5 x 4 mm - 12 x 8 mm	C. HOT	MLTPL
	Food Grade Fittings 71000	4 mm - 15 mm	C. HOT	MLTPL
	Food Grade Fittings 71010	6 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71015	6 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71020	4 mm - 15 mm	C. HOT	MLTPL
	Food Grade Fittings 71021	4 mm - 6 mm	C. HOT	MLTPL
	Food Grade Fittings 71030	6 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71040	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71050	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71100	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71101	6 mm	C. HOT	MLTPL
	Food Grade Fittings 71110	4 mm - 10 mm	C. HOT	MLTPL
	Food Grade Fittings 71115	4 mm - 10 mm	C. HOT	MLTPL
	Food Grade Fittings 71120	5 mm - 10 mm	C. HOT	MLTPL
	Food Grade Fittings 71130	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71200	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71210	6 mm - 10 mm	C. HOT	MLTPL
	Food Grade Fittings 71215	6 mm - 10 mm	C. HOT	MLTPL
	Food Grade Fittings 71220	5 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71230	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71300	5 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71410	5 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71420	1/8" - 1/2"	C. HOT	MLTPL
	Food Grade Fittings 71430	1/8" - 1/2"	C. HOT	MLTPL
	Food Grade Fittings 71500	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings 71510	4 mm - 12 mm	C. HOT	MLTPL
	Food Grade Fittings LG71410	5 mm - 6 mm	C. HOT	MLTPL
	Food Grade Fittings LG71500	4 mm - 6 mm	C. HOT	MLTPL

Aikang Remetech Co. Ltd.
137-130, Il-dong Bldg, 3 Fl
#60, Yangjae-dong, Socho-ku
Seoul
Korea, Republic of
82 2 578 8131

Facility : Chungnam, Korea, Republic of

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Tubing
	Aikang	3/8" - 2"	C. HOT	PB

Air Logistics Corp.
925 North Todd Avenue
Azusa, CA 91702
United States
626-633-0294

Facility : Azusa, CA

Joining and Sealing Materials

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Sealants
	Aquapreg™	2.0 sq. in./L	C. HOT	SLT
	Aquawrap™	2.0 sq. in./L	C. HOT	SLT

Akron Porcelain & Plastics Company
2739 Cory Avenue
Akron, OH 44314-0157
United States
330-745-2159

Facility : Akron, OH

Process Media

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Aeration Packing Material
	Porcelain Spheres	>= 1 1/4" diameter	CLD 23	SYN

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.

Akzo Nobel Coatings Inc.
P.O. Box 91629
Cleveland, OH 44101
United States
216-750-6475

Facility : Warsaw, IN

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Tank[1]
	HA000Q White	>= 4000 gal.	CLD 23	PEC
[1] Colors: White Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 10 Final Cure Time and Temperature: 15 minutes at 350°F

Facility : Nashville, TN

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	R4-ES HKF47R[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES (HJF24R)[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES (HJF67R)[3]	>= 1"	D. HOT	PEC
	Resicoat R4-ES (HKF61R)[4]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HGF17R Rust[5]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJ606R Blue[6]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF10R Blue[6]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF14R Blue[6]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF42R Blue[6]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HGC17R Red[7]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC08R Blue[8]	>= 1"	D. HOT	PEC
[1] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 35 Final Cure Time and Temperature: 455°F metal temperature and post cured for 10 minutes at 455°F Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates are then post cured for 10 minutes at 455°F. [2] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 428°F Special Comments: Self curing on 8 mm or heavier steel at 392°F - 428°F metal temperature. [3] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 16 Final Cure Time and Temperature: 10 minutes at 455°F Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates are then post cured for 10 minutes at 455°F. [4] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 35 Final Cure Time and Temperature: 10 minutes at 455°F Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates are then post cured for 10 minutes at 455°F. [5] Colors: Rust Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 428°F [6] Colors: Blue Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Maximum Thinner: None Final Cure: 20 minutes at 428°F [7] Colors: Red Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat at 200°C - 230°C [8] Colors: Blue Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Recoat Cure Time and Temperature: 20 minutes at 220°C Special Comments: Pre-heat at 200°C - 230°C
Coatings - Tank
	HA000Q White[9]	>= 4000 gal.	CLD 23	PEC
	VE-700001 Blue Epoxy[10]	>= 4.5 gal.	D. HOT	PEC
[9] Colors: White Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 10 Final Cure Time and Temperature: 15 minutes at 350°F [10] Colors: Blue Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 3 Recoat/Cure Time: 15 minutes at 350°F
Coatings - Valve
	R4-ES HKF47R[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES (HJF24R)[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES (HJF67R)[3]	>= 1"	D. HOT	PEC
	Resicoat R4-ES (HKF61R)[4]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HGF17R Rust Red[5]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF10R Blue[6]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF14R Blue[6]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF42R Blue[6]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HGC17R Red[7]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC08R Blue[8]	>= 1"	D. HOT	PEC
[1] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 35 Final Cure Time and Temperature: 455°F metal temperature and post cured for 10 minutes at 455°F Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates are then post cured for 10 minutes at 455°F. [2] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 428°F Special Comments: Self curing on 8 mm or heavier steel at 392°F - 428°F metal temperature. [3] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 16 Final Cure Time and Temperature: 10 minutes at 455°F Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates are then post cured for 10 minutes at 455°F. [4] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 35 Final Cure Time and Temperature: 10 minutes at 455°F Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates are then post cured for 10 minutes at 455°F. [5] Colors: Rust Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 428°F [6] Colors: Blue Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Maximum Thinner: None Final Cure: 20 minutes at 428°F [7] Colors: Red Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat at 200°C - 230°C [8] Colors: Blue Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 20 Recoat Cure Time and Temperature: 20 minutes at 220°C Special Comments: Pre-heat at 200°C - 230°C

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.

Akzo Nobel Coatings, Inc.
Flying Hills Corporate Center
5 Commerce Drive
Reading, PA 19607
United States
610-775-6600

Facility : Reading, PA

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	Corvel 10-5110 Corvel Blue[2]	>= 1/2"	CLD 23	PEC
	Corvel® 10-1160 Jersey Cream[3]	>= 2"	CLD 23	PEC
	Corvel® 10-4037 Corvel Red[1]	>= 2"	CLD 23	PEC
	Corvel® 10-4081 Corvel Red Brown[1]	>= 2"	CLD 23	PEC
	Corvel® 10-7314[5]	>= 1/2"	CLD 23	PEC
	Corvel® 10-7561 Gray[3]	>= 2"	CLD 23	PEC
	Corvel® White 10-1161[3]	>= 2"	CLD 23	PEC
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat part to 350°F for 15 minutes. [2] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat to 350°F for 20 minutes. [3] Colors: White Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 15 Maximum Thinner: None Final Cure Time and Temperature: 20 minutes at 350°F Special Comments: Preheat substrate to 350°F [5] Colors: Black Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat to 350°F for 20 minutes.
Coatings - Pipe
	Corvel® 10-1160 Jersey Cream[3]	>= 2"	CLD 23	PEC
	Corvel® 10-4037 Corvel Red[1]	>= 2"	CLD 23	PEC
	Corvel® 10-4081 Corvel Red Brown[1]	>= 2"	CLD 23	PEC
	Corvel® 10-7314[5]	>= 1/2"	CLD 23	PEC
	Corvel® 10-7561 Gray[3]	>= 2"	CLD 23	PEC
	Corvel® White 10-1161[3]	>= 2"	CLD 23	PEC
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat part to 350°F for 15 minutes. [3] Colors: White Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 15 Maximum Thinner: None Final Cure Time and Temperature: 20 minutes at 350°F Special Comments: Preheat substrate to 350°F [5] Colors: Black Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat to 350°F for 20 minutes.
Coatings - Tank
	Corvel® 10-1160 Jersey Cream[3]	>= 5 gal.	CLD 23	PEC
	Corvel® 10-2026[4]	>= 25 gal.	CLD 23	PEC
	Corvel® 10-4037 Corvel Red[1]	>= 5 gal.	CLD 23	PEC
	Corvel® 10-4081 Corvel Red Brown[1]	>= 5 gal.	CLD 23	PEC
	Corvel® 10-5063 Corvel Dark Blue[1]	>= 5 gal.	CLD 23	PEC
	Corvel® 10-5110 Corvel Blue[2]	>= 5 gal.	CLD 23	PEC
	Corvel® 10-7208 Corvel Gray[1]	>= 5 gal.	CLD 23	PEC
	Corvel® 10-7314 Corvel[5]	>= 5 gal.	CLD 23	PEC
	Corvel® 10-7561 Gray[3]	>= 5 gal.	CLD 23	PEC
	Corvel® White 10-1161[3]	>= 5 gal.	CLD 23	PEC
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat part to 350°F for 15 minutes. [2] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat to 350°F for 20 minutes. [3] Colors: White Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 15 Maximum Thinner: None Final Cure Time and Temperature: 20 minutes at 350°F Special Comments: Preheat substrate to 350°F [4] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 30 Final Cure: 350°F for 20 minutes Special Comments: The part to be coated must be clean with an abrasive blast cleaned surface of 1.5-3 mil anchor profile. Parts to be coated must be preheated to 350°F metal temperature prior to application of powder coating. [5] Colors: Black Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat to 350°F for 20 minutes.
Coatings - Valve
	Corvel® 10-5110 Corvel Blue[2]	>= 1/2"	CLD 23	PEC
	Corvel® 10-5112 Corvel Blue[1]	>= 4"	CLD 23	PEC
	Corvel® 10-7314[5]	>= 1/2"	CLD 23	PEC
	Corvel® White 10-1161	>= 2"	CLD 23	PEC
[1] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat part to 350°F for 15 minutes. [2] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat to 350°F for 20 minutes. [5] Colors: Black Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 16 Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post heat to 350°F for 20 minutes.

Akzo Nobel Powder Coatings GmbH
Markwiesenstr. 50
D-72770 Reutlingen
Germany
49 712 151 9145

Facility : Suzhou, China

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings[1]
	Resicoat R4-ES HGF04R Red	>= 1"	D. HOT	PEC
	Resicoat R4-ES HGF17R Rust Red	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF01R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF10R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF14R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF24R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF42R Blue	>= 1"	D. HOT	PEC
[1] Colors: Blue, Red Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 20 Recoat Cure Time and Temperature: 20 minutes at 428°F
Coatings - Valve[1]
	Resicoat R4-ES HGF04R Red	>= 1"	D. HOT	PEC
	Resicoat R4-ES HGF17R Rust Red	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF01R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF10R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF14R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF24R Blue	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF42R Blue	>= 1"	D. HOT	PEC
[1] Colors: Blue, Red Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 20 Recoat Cure Time and Temperature: 20 minutes at 428°F

Facility : Reutlingen, Germany

Protective (Barrier) Materials

			Water	Water
		Water Contact	Contact	Contact
	Trade Designation	Size Restriction	Temp	Material
Coatings - Fittings
	Resicoat R4-ES HGF03R Red-Brown[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HGF10R Red[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJC06R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF01R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF10R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF14R Blue[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF21R Blue[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF22R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF23R Saphir-Blue[3]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF57R Blue[4]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HGC07R Red-Brown[1]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC033R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC04R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC08R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC26R Blue[2]	>= 1"	D. HOT	PEC
[1] Color: Blue, red, red-brown Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 20 Maximum Thinner: None Recoat Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat temperature 200°C - 230°C [2] Colors: Blue Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 20 Maximum Thinner: None Final Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat temperature 200°C - 230°C [3] Colors: Blue Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 12 Maximum Thinner: None Final Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat temperature 200°C - 230°C [4] Colors: Blue Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 200°C Special Comments: Preheat substrate to 180°C - 220°C
Coatings - Valve
	Resicoat R4-ES HGF03R Red-Brown[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HGF10R Red[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJC06R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF01R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF10R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF14R Blue[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF21R Blue[1]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF22R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF23R Saphir-Blue[3]	>= 1"	D. HOT	PEC
	Resicoat R4-ES HJF57R Blue[4]	>= 1"	D. HOT	PEC
	Resicoat R4-FB H6C07R Red-Brown[1]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC033R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC04R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC08R Blue[2]	>= 1"	D. HOT	PEC
	Resicoat R4-FB HJC26R Blue[2]	>= 1"	D. HOT	PEC
[1] Color: Blue, red, red-brown Number of Coats: 1 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 20 Maximum Thinner: None Recoat Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat temperature 200°C - 230°C [2] Colors: Blue Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 20 Maximum Thinner: None Final Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat temperature 200°C - 230°C [3] Colors: Blue Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 12 Maximum Thinner: None Final Cure Time and Temperature: 20 minutes at 220°C Special Comments: Preheat temperature 200°C - 230°C [4] Colors: Blue Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 20 Final Cure Time and Temperature: 20 minutes at 200°C Special Comments: Preheat substrate to 180°C - 220°C

Al Wasail Industrial Company
King Abdulaziz Street
P.O. Box 124
Buraydah 51411
Saudi Arabia
966 6 3816658
Visit this company's website

Facility : Buraydah, Saudi Arabia

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Pipe
	Al-Wasail PW HDPE Pipes	20 mm - 1200 mm	D. HOT	HDPE

Al-Jazea Industrial Co.
P.O. Box: 16793
Riyadh 11474
Saudi Arabia
966 1 4981919
Visit this company's website

Facility : Dammam, Saudi Arabia

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Fittings
	E-KS Flanged Socket	[1]	D. HOT	MLTPL
	MMA-KS Double Socket Tee With Flanged Branch	[2]	D. HOT	MLTPL
	MMB-KS All Socket Tee	[3]	D. HOT	MLTPL
[1] 50 mm x 63 mm - 400 mm x 400 mm [2] 80 mm x 80 mm x 80 mm - 200 mm x 200 mm x 200 mm [3] 80 mm x 80 mm x 80 mm - 150 mm x 150 mm x 150 mm

Facility : Dammam/Eastern Province, Saudi Arabia

Pipes and Related Products

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Pipe
	JPEPICO HDPE Pipes	20 - 400 mm	C. HOT	PE

Alamo Water Refiners
13700 Highway 90 West
San Antonio, TX 78245
United States
800-659-8400

Facility : # 1 Brazil

Process Media

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Oxidative Media
	Filox	20 x 40 mesh	CLD 23	MNDOX

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.

Alberta Custom Tee, Ltd.
10037-96 Avenue
Westlock, AB T7P-2P9
Canada
780-349-6511

Facility : Westlock, Alberta, Canada

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Manifolds
	Copper Manifolds[1]	[2]	C. HOT	CU
[1] Only copper manifolds with copper parts are Certified. Copper manifolds with brass fittings are not Certified. [2] The following part numbers, configurations and sizes are Certified. All manifolds are 72" long (unless otherwise noted) and may be cut to the desired length. Pipe run 1", 1 1/4", 1 1/2" or 2" with 24 copper outlets 1/2" or 3/4" on 3" CTRS. CC1005024 1 X 1/2 CU CC1255024 1 1/4 X 1/2 CU CC1505024 1 1/2 X 1/2 CU CC2005024 2 X 1/2 CU CC1007524 1 X 3/4 CU CC1257524 1 1/4 X 3/4 CU CC1507524 1 1/2 X 3/4 CU CC2007524 2 X 3/4 CU Pipe run 1", 1 1/4", 1 1/2" or 2" with 18 copper outlets 1/2", 3/4", or 1" on 4" CTRS CC1005018 1 X 1/2 CU CC1255018 1 1/4 X 1/2 CU CC1505018 1 1/2 X 1/2 CU CC2005018 2 X 1/2 CU CC1007518 1 X 3/4 CU CC1257518 1 1/4 X 3/4 CU CC1507518 1 1/2 X 3/4 CU CC2007518 2 X 3/4 CU CC1251018 1 1/4 X 1 CU CC1501018 1 1/2 X 1 CU CC2001018 2 X 1 CU Pipe run 1", 1 1/4", 1 1/2" or 2" with 12 copper outlets 1/2", 3/4", or 1" on 6" CTRS. CC1005012ER 1 X 1/2 CU CC1255012ER 1 1/4 X 1/2 CU CC1505012ER 1 1/2 X 1/2 CU CC2005012ER 2 X 1/2 CU CC1007512ER 1 X 3/4 CU CC1257512ER 1 1/4 X 3/4 CU CC1507512ER 1 1/2 X 3/4 CU CC2007512ER 2 X 3/4 CU CC1251012ER 1 1/4 X 1 CU CC1501012ER 1 1/2 X 1 CU CC2001012ER 2 X 1 CU Pipe run 62" long, 1" with 30 copper outlets 1/2" on 2" CTRS. CC1005030 1 X 1/2 CU Compact Headers - Pipe run 1" with 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, or 12 copper outlets 1/2" on 1 1/2" CTRS. CC1005002 1 X 1/2 CU CC1005003 1 X 1/2 CU CC1005004 1 X 1/2 CU CC1005005 1 X 1/2 CU CC1005006 1 X 1/2 CU CC1005007 1 X 1/2 CU CC1005008 1 X 1/2 CU CC1005009 1 X 1/2 CU CC1005010 1 X 1/2 CU CC1005011 1 X 1/2 CU CC1005012 1 X 1/2 CU Speedy copper headers - closed one end and reduced 3/4" female sweat the other end. SC1005002RD 1 X 1/2 CU SC1005003RD 1 X 1/2 CU SC1005004RD 1 X 1/2 CU SC1005005RD 1 X 1/2 CU SC1005006RD 1 X 1/2 CU SC1005007RD 1 X 1/2 CU SC1005008RD 1 X 1/2 CU SC1005009RD 1 X 1/2 CU SC1005010RD 1 X 1/2 CU SC1005011RD 1 X 1/2 CU SC1005012RD 1 X 1/2 CU Speedy copper headers - closed one end and 1" plain the other end. SC1005002PL 1 X 1/2 CU SC1005003PL 1 X 1/2 CU SC1005004PL 1 X 1/2 CU SC1005005PL 1 X 1/2 CU SC1005006PL 1 X 1/2 CU SC1005007PL 1 X 1/2 CU SC1005008PL 1 X 1/2 CU SC1005009PL 1 X 1/2 CU SC1005010PL 1 X 1/2 CU SC1005011PL 1 X 1/2 CU SC1005012PL 1 X 1/2 CU

Allchem Performance Products
416 South Main Street
Corsicana, TX 75110
United States
903-872-9997

Facility : Corsicana, TX

Mechanical Devices

			Water	Water
			Contact	Contact
	Trade Designation	Size	Temp	Material
Chemical Feeders[1]
	Horizon PCF-60	[2]	CLD 23	MLTPL
	Horizon PTF-60	[3]	CLD 23	MLTPL
[1] Certification of this product has been performed to the health effects requirements of NSF/ANSI Standard 61, which assesses the acceptability of potential extractants from the chemical feeder when used with the manufacturer's recommended use chemicals. Any modifications including the use of chemicals other than those recommended by the manufacturer and chemicals that are not compliant to NSF/ANSI Standard 60 will void the NSF Certification for this feeder. [2] Horizon PCF-60 is Certified for a maximum 0.2% calcium hypochlorite solution added to drinking water to effect a maximum use level (MUL) of 10 ppm total chlorine, with a minimum of 47,500 gallons of water treated per day. [3] Horizon PTF-60 is Certified for a maximum 0.11% trichloroisocyanurate solution added to drinking water to effect a maximum use level (MUL) of 10 ppm total chlorine, with a minimum of 18,000 gallons of water treated per day.

Almar SRL
Via Dello Sport 17bis
21026 Gavirate (VA)
Italy
39 0332 743961
Visit this company's website

44.3056.efg PL-HC-TT-IT-PCA 1.5gpm[3] [G] 44.3058.efg PL-HC-TT-IT-PCA 1.0gpm[3] [G] 44.3060.efg PL-HC-TT-IT-PCA 1.25gpm[3] [G] 44.3061.efg PL-HC-TT-IT-PCA 1.75gpm[3] [G] 44.3130.efg PL-HC-TT-IT-lam V[3] [G] 44.3131.efg PL-HC-TT-IT-lam 1.0gpm[3] [G] 44.3132.efg PL-HC-TT-IT-lam 1.5gpm[3] [G] 44.3133.efg PL-HC-TT-IT-lam 2.0gpm[3] [G] 44.3134.efg PL-HC-TT-IT-lam 2.2gpm[3] [G] 44.3139.efg PL-HC-TT-IT-lam 1.75gpm[3] [G] 44.3151.efg PL-HC-TT-IT-PCA-lam 5,0l/min[3] [G] 44.3153.efg PL-HC-TT-IT-PCA-lam 2.2gpm[3] [G] 44.3154.efg PL-HC-TT-IT-PCA-lam 8,0l/min[3] [G] 44.3155.efg PL-HC-TT-IT-PCA-lam 7,0l/min[3] [G] 44.3156.efg PL-HC-TT-IT-PCA-lam 1.5gpm[3] [G] 44.3157.efg PL-HC-TT-IT-PCA-lam 2.0gpm[3] [G] 44.3158.efg PL-HC-TT-IT-PCA-lam 1.0gpm[3] [G] 44.3159.efg PL-HC-TT-IT-PCA-lam 0.5gpm[3] [G] 44.3160.efg PL-HC-TT-IT-PCA-lam 1.25gpm[3] [G] 44.3161.efg PL-HC-TT-IT-PCA-lam 1.75gpm[3] [G] 44.3164.efg PL-HC-TT-IT-PCA-lam 3.0gpm[3] [G] 44.3230.010 CACHÉ-HC-TT-m M16,5x1 V[3] [G] 44.3230.060 CACHÉ-HC-XT-TT-m M16,5x1 V[3] [G] 44.3231.010 CACHÉ-HC-TT-m M16,5x1 1.0gpm[3] [G] 44.3231.060 CACHÉ-HC-XT-TT-m M16,5x1 1.0gpm[3] [G] 44.3232.010 CACHÉ-HC-TT-m M16,5x1 1.5gpm[3] [G] 44.3232.060 CACHÉ-HC-XT-TT-m M16,5x1 1.5gpm[3] [G] 44.3233.010 CACHÉ-HC-TT-m M16,5x1 2.0gpm[3] [G] 44.3233.060 CACHÉ-HC-XT-TT-m M16,5x1 2.0gpm[3] [G] 44.3234.010 CACHÉ-HC-TT-m M16,5x1 2.2gpm[3] [G] 44.3234.060 CACHÉ-HC-XT-TT-m M16,5x1 2.2gpm[3] [G] 44.3239.010 CACHÉ-HC-TT-m M16,5x1 1.75gpm[3] [G] 44.3239.060 CACHÉ-HC-XT-TT-m M16,5x1 1.75gpm[3] [G] 44.3251.010 CACHÉ-HC-TT-m M16,5x1-PCA 5,0l/min[3] [G] 44.3251.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 5,0l/min[3] [G] 44.3253.010 CACHÉ-HC-TT-m M16,5x1-PCA 2.2gpm[3] [G] 44.3253.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 2.2gpm[3] [G] 44.3254.010 CACHÉ-HC-TT-m M16,5x1-PCA 8,0l/min[3] [G] 44.3254.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 8,0l/min[3] [G] 44.3255.010 CACHÉ-HC-TT-m M16,5x1-PCA 7,0l/min[3] [G] 44.3255.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 7,0l/min[3] [G] 44.3256.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.5gpm[3] [G] 44.3256.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.5gpm[3] [G] 44.3257.010 CACHÉ-HC-TT-m M16,5x1-PCA 2.0gpm[3] [G] 44.3257.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 2.0gpm[3] [G] 44.3258.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.0gpm[3] [G] 44.3258.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.0gpm[3] [G] 44.3260.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.25gpm[3] [G] 44.3260.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.25gpm[3] [G] 44.3261.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.75gpm[3] [G] 44.3261.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.75gpm[3] [G] 44.3330.010 CACHÉ-HC-TT-m M16,5x1-lam V[3] [G] 44.3330.060 CACHÉ-HC-XT-TT-m M16,5x1-lam V[3] [G] 44.3331.010 CACHÉ-HC-TT-m M16,5x1-lam 1.0gpm[3] [G] 44.3331.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 1.0gpm[3] [G] 44.3332.010 CACHÉ-HC-TT-m M16,5x1-lam 1.5gpm[3] [G] 44.3332.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 1.5gpm[3] [G] 44.3333.010 CACHÉ-HC-TT-m M16,5x1-lam 2.0gpm[3] [G] 44.3333.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 2.0gpm[3] [G] 44.3334.010 CACHÉ-HC-TT-m M16,5x1-lam 2.2gpm[3] [G] 44.3334.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 2.2gpm[3] [G] 44.3339.010 CACHÉ-HC-TT-m M16,5x1-lam 1.75gpm[3] [G] 44.3339.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 1.75gpm[3] [G] 44.3351.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 5,0l/min[3] [G] 44.3351.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 5,0l/min[3] [G] 44.3353.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 2.2gpm[3] [G] 44.3353.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 2.2gpm[3] [G] 44.3354.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 8,0l/min[3] [G] 44.3354.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 8,0l/min[3] [G] 44.3355.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 7,0l/min[3] [G] 44.3355.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 7,0l/min[3] [G] 44.3356.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.5gpm[3] [G] 44.3356.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.5gpm[3] [G] 44.3357.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 2.0gpm[3] [G] 44.3357.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 2.0gpm[3] [G] 44.3358.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.0gpm[3] [G] 44.3358.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.0gpm[3] [G] 44.3359.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 0.5gpm[3] [G] 44.3360.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.25gpm[3] [G] 44.3360.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.25gpm[3] [G] 44.3361.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.75gpm[3] [G] 44.3361.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.75gm[3] [G] 44.3364.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 3.0gpm[3] [G] 44.7158.efg PCA-SPRAY-TT-IT 1.0gpm[3] [G] 44.7159.efg PCA-SPRAY-TT-IT 0.5gpm[3] [G] 44.7165.efg PCA-SPRAY-TT-IT 0.38gpm[3] [G] 44.7168.efg PCA-SPRAY-TT-IT 0.35gpm[3] [G] 44.7358.010 CACHÉ-PCA-Spray-TT-m M16,5x1 1.0gpm[3] [G] 44.7359.010 CACHÉ-PCA-Spray-TT-m M16,5x1 0.5gpm[3] [G] 45.2002.000 PL-HC-CS-STD-m M24x1 Z[5] [G] 45.2003.000 PL-HC-CS-STD-m M24x1 A[5] [G] 45.2005.000 PL-HC-CS-STD-m M24x1 B[5] [G] 45.2006.000 PL-HC-CS-STD-m M24x1 C[5] [G] 45.2051.000 PL-HC-CS-STD-m M24x1-PCA 5.0L[5] [G] 45.2053.000 PL-HC-CS-STD-m M24x1-PCA 2.2 gpm[5] [G] 45.2053.050 PL-HC-CS-STD-m 15/16-27-PCA 2.2 gpm[5] [G] 45.2053.220 PL-HC-CS-JR-PCA 2.2 gpm[5] [G] 45.2054.000 PL-HC-CS-STD-m M24x1-PCA 8.0L[5] [G] 45.2055.000 PL-HC-CS-STD-m M24x1-PCA 7.0L[5] [G] 45.2056.000 PL-HC-CS-STD-m M24x1-PCA 1.5 gpm[5] [G] 45.2056.050 PL-HC-CS-STD-m 15/16-27-PCA 1.5 gpm[5] [G] 45.2056.220 PL-HC-CS-JR-PCA 1.5 gpm[5] [G] 45.2057.000 PL-HC-CS-STD-m M24x1-PCA 2.0 gpm[5] [G] 45.2057.050 PL-HC-CS-STD-m 15/16-27-PCA 2.0 gpm[5] [G] 45.3030.000 PL-HC-CS-STD-m M24x1 V[5] [G] 45.3030.050 PL-HC-CS-STD-m 15/16-27 V[5] [G] 45.3030.220 PL-HC-CS-JR V[5] [G] B1.1107.1.efghi[6] [G] B1.1207.1.efghi[6] [G] B1.1307.1.efghi[6] [G] B1.1407.1.efghi[6] [G] B1.1707.1.efghi[G] B1.1807.1.efghi[G] B1.1907.1.efghi[6] [G] B1.1G07.1.efghi[6] [G] B1.1K07.1.efghi[6] [G] B1.1M07.1.efghi[6] [G] B1.1N07.1.efghi[6] [G] B1.2107.1.efghi[6] [G] B1.2207.1.efghi[6] [G] B1.2307.1.efghi[6] [G] B1.2707.1.efghi[G] B1.2807.1.efghi[G] B1.2907.1.efghi[6] [G] B1.2M07.1.efgh[6] [G] B1.2N07.1.efghi[6] [G] B1.AU13.1.1171 Spring-Flo Ultra Female[G] B1.AU23.1.3171 Spring-Flo Ultra Male[G] B1.AU73.1.7171 Spring-Flo Ultra Dual Thread[G] B1.D107.1.efghi[6] [G] B1.D204.1.efghi[6] [G] B1.D307.1.efghi[6] [G] B1.D707.1.efghi[G] B1.D807.1.efghi[G] B1.D907.1.efghi[6] [G] B1.DN07.1.efghi[6] [G] B9.1107.1.efghi[6] [G] B9.1207.1.efghi[6] [G] B9.1307.1.efghi[6] [G] B9.1407.1.efghi[6] [G] B9.1707.1.efghi[G] B9.1807.1.efghi[G] B9.1G07.1.efghi[6] [G] B9.1K07.1.efghi[6] [G] B9.1M07.1.efghi[6] [G] B9.1N07.1.efghi[6] [G] B9.2107.1.efghi[6] [G] B9.2207.1.efghi[6] [G] B9.2307.1.efghi[6] [G] B9.2707.1.efghi[G] B9.2807.1.efghi[G] B9.2907.1.efghi[6] [G] B9.2M07.1.efghi[6] [G] B9.2N07.1.efghi[6] [G] B9.D107.1.efghi[6] [G] B9.D204.1.efghi[6] [G] B9.D307.1.efghi[6] [G] B9.D707.1.efghi[G] B9.D807.1.efghi[G] B9.D907.1.efghi[6] [G] B9.DN07.1.efghi[6] [G] Bx.abcd.1.efghi Cascade Flow Restricting Aerators[1] [G] Bx.abcd.1.efghi Cascade Flow Restricting Aerators[1] [G] Bx.abcd.1.efghi PCA Cascade Aerators[1] [G] Bx.abcd.1.efghi PCA Spray Laminar Aerators[1] [G] Bx.abcd.1.efghi Perlator TT Aerated Flow Aerators[1] [G] Bx.abcd.1.efghi Perlator TT Laminar Flow Aerators[1] [G] Bx.abcd.1.efghi Spring-Flo Aerators[1] DEAL #38D[1] DEAL #40E[1] G1.A313.1.C171 Low Lead Spring-Flo[G] G1.A373.1.D171 Low Lead Spring-Flo[G] G1.A3G3.1.C171 Low Lead Spring-Flo[G] Rx.abcd.1.efghi Cascade Flow Restricting Aerators[1] [G] Rx.abcd.1.efghi Cascade Flow Restricting Aerators[1] [G] Rx.abcd.1.efghi PCA Spray Laminar Aerators[1] [G] Rx.abcd.1.efghi Perator TT Aerated Flow Aerators[1] [G] Rx.abcd.1.efghi Perlator TT Laminar Flow Aerators[1] [G] Rx.abcd.1.efghi Spring-Flo Aerators[1]

[1] All aerators, faucet end attachments, snap fittings, and couplers are designated
    according to one of the following numbering schemes: Bx.abcd.1.efghi or Rx.abcd.1.efghi.
     Aerator replacement components that begin with A or 0 do not follow the numbering
    scheme. The part number is individual. 
    B  - Neoperl North America
    R  - Retail
    x  - Assembly stage
         1   - Aerator
         2   - Insert with dome screen
         3   - Insert without dome
         9   - Vandal proof aerator
         B   - Unassembled aerator
         C   - Vandal proof aerator with hose guard
         E   - Aerator with adapter
         F   - Cachè
         V** - Components
         W** - Washer
         X*  - Adapters/couplers/swivels
    a  - Product type
         0 - Void
         1 - Perlator
         2 - Perlator Jr.
         3 - Cascade
         4 - NEOPERL - LL
         6 - Spray
         7 - Care (laminar)
         A - Spring flo 
         B - Spring flo Jr.   
         C - Perlator/short
         D - Perlator laminar Jr.
         E - Perlator Tom Thumb 
         F - Laminar Tom Thumb 
         G - R O coupler
         H - Spray Jr.
         L - Perlator laminar
         M - Careguard
         S - SLC aerator
    b  - Flow rate
         0 - Void
         1 - 1.5 gpm
         2 - 2.0 gpm
         3 - 2.2 gpm
         4 - 3.0 gpm
         5 - PCA 0.5 gpm (1,7 L)
         6 - PCA 1.0 gpm (3,5 L)
         7 - PCA 1.5 gpm (5,0 L)
         8 - PCA 2.2 gpm (8,3 L)
         9 - FF (full-flow)
         A - Class A
         B - Class B
         C - Class C
         D - Class D
         E - Class U
         F - Class Z
         G - 3.5 gpm
         H - Class M
         J - PCA 8.0 L
         K - 4.0 gpm
         L - Max flow
         M - 4.5 gpm
         N - 1.0 gpm
         Q - PCA .66 gpm (2,5 L)
         R - PCA 1.75 gpm (6,0 L)
    c  - Housing thread (letter or number representing housing thread)
    d  - Finish/color (letter or number representing finish/color)
    1  - Place holder (constant)
    e  - Washer # 
         0 - Void
         1 - BW.7134.1 (lg .072)
         2 - BW.7134.1 (lg .072)
         3 - BW.7110.1 (lg .095)
         4 - BW.7110.1 (lg .095)
         5 - BW.7411.1 (lg .125)
         6 - BW.5065.1 & BW.7134.1 (dt .075)
         7 - BW.5065.1 & BW.7134.1 (dt .075)
         8 - BW.7129.1 (jr. PCA .125)
         9 - BW.7476.1 (jr .125)
         A - BW.6313.1 (jr .144)
         B - BW.7102.1 (jr. PCA .144)
         C - BV.6217.1 lg. spring flo
         D - BW.0002.1 (.828 santoprene)
         E - BV.6230.1 sm. spring flo
         F - BW.6309.1 (jr. .062)
         G - 55.1149.1 (TT .110)
         H - 55.1148.1 (TT .060)
         J - BW.0003.1 (Chicago fct)
         K - BW.0005.1
         L - BW.0006.1
         M - 55.1252.1 (M28)  
    fg - Marking (letters and numbers respresenting marking)
    h  - Packaging (letter or number representing packaging)
    i  - Customer name (letter representing customer labeling)
    *  - Random numbers  
         a - Product type
         b - Flow rate
         c - Housing tread
    ** - Random numbers
         a - Product type
         b - Flow rate
         c - Housing tread
         d - Finsh/color
[2] 42  - JR size MC Aerators
    a   - Line/model
          2 - Perlator honeycomb
          3 - Perlator honeycomb (diffuser technology)
    b   - Aerated/laminar (incl. CACHÉ)
          0 - Aerated
          1 - Laminar
          2 - Aerated CACHÉ
          3 - Laminar CACHÉ
    cd  - Flow rate
          01 - X
          02 - Z
          03 - A
          05 - B
          30 - Diffuser V
          31 - Diffuser 1.0 gpm
          32 - Diffuser 1.5 gpm
          33 - Diffuser 2.0 gpm
          34 - Diffuser 2.2 gpm
          39 - Diffuser 1.75 gpm
          51 - PCA 5.0 L
          53 - PCA 2.2 gpm
          54 - PCA 8.0 L
          56 - PCA 1.5 gpm
          57 - PCA 2.0 gpm
          58 - PCA 1.0 gpm
          60 - PCA 1.25 gpm
          61 - PCA 1.75 gpm
    efg - Brass housing/surface thread
    
    Part numbers may also contain an additional numeric suffix to indicate packaging and
    external markings.
[3] efg - brass housing/surface thread
    
    Part numbers may also contain an additional numeric suffix to indicate packaging and
    external markings.
[4] 43 - TJ Size MC Aerators
    
    ab – Line
    20- Perlator Honeycomb
    21- Perlator Honeycomb laminar
    22- CACHÉ Perlator Honeycomb
    23 -CACHÉ Perlator Honeycomb laminar
    30 –Perlator Honeycomb (diffuser technology)
    31 - Perlator Honeycomb (diffuser technology) laminar
    32 - CACHÉ Perlator Honeycomb (diffuser technology)
    33 - CACHÉ Perlator Honeycomb (diffuser technology) laminar
    60 – SSR (Aerator with swiveling honeycomb plate)
    
    cd - Flow rate
    01 - X
    02 - Z
    03 - A
    05 - B
    30 - Diffuser V
    31 - Diffuser 1.0gpm
    32 - Diffuser 1.5gpm
    33 - Diffuser 2.0gpm
    34 - Diffuser 2.2gpm
    39 - Diffuser 1.75gpm
    51 - PCA 5.0L
    53 - PCA 2.2gpm
    54 - PCA 8.0L
    55 - PCA 7.0L
    56 - PCA 1.5gpm
    57 - PCA 2.0gpm
    58 - PCA 1.0gpm
    60 - PCA 1.25gpm
    61 - PCA 1.75gpm
    
    efg - brass housing/surface thread
    
    Part numbers may also contain an additional numeric suffix to indicate packaging and
    external markings.
[5] PL  - Perlator
    HC  - Honeycomb
    CS  - Coinslot
    STD - Standard size
    JR  - Junior size
    PCA - Pressure compensation aerator
[6] e  - Washer #
         0 - void
         1 - BW.7134.1 (lg .072)
         2 - BW.7134.1 (lg .072)
         3 - BW.7110.1 (lg .095)
         4 - BW.7110.1 (lg .095)
         5 - BW.7411.1 (lg .125)
         6 - BW.5065.1 & BW.7134.1 (dt.075)
         7 - BW.5065.1 & BW.7134.1 (dt.075)
         8 - BW.7129.1 (jr. PCA .125)
         9 - BW.7476.1 (jr .125)
         A - BW.6313.1 (jr .144)
         B - BW.7102.1 (jr. PCA .144)
         C - BV.6217.1 Lg. Spring Flo
         E - BV.6230.1 Sm. Spring Flo
         F - BW.6309.1 (jr. .062)
         G - 55.1149.1 (TT .110)
         H - 55.1148.1 (TT .060)
         J - BW.0003.1 (Chicago Fct)
         K - BW.0005.1
         L - BW.0006.1
         M - 55.1252.1 (M28)
    fg - Marking (letters and numbers representing marking)
    h  - Packaging (letter or number representing packaging)
    i  - Customer Name (letter representing customer labeling)
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Aerator Replacement Components[1] 02.5601.0[G] 02.5603.0[G] 02.5607.1[G] 02.5608.0[G] 02.5611.0[G] 02.5613.0[G] 02.5614.0[G] 02.5617.0[G] 02.5618.0[G] 02.8201.0[G] 02.8301.0[G] 02.8311.0[G] 02.8321.0[G] 02.8351.0[G] 54.1270.1 55.1148.1[G] 55.1149.1[G] 55.1162.1[G] 55.1211.1[G] 55.1217.1[G] 55.1223.1[G] 55.1252.1[G] A5.4130.0[G] A5.4132.0[G] A5.4143.0[G] A5.4145.0[G] A5.4146.0[G] A5.4160.0[G] A5.4162.0[G] A5.4163.0[G] A5.4165.0[G] A5.4166.0[G] A5.9035.1[G] A5.9036.1[G] A5.9042.1[G] A5.9043.1[G] A5.9044.1[G] A5.9045.1[G] A5.9046.1[G] Bx.abcd.1.efghi Rx.abcd.1.efghi[1]

[1] All aerators, faucet end attachments, snap fittings, and couplers are designated
    according to one of the following numbering schemes: Bx.abcd.1.efghi or Rx.abcd.1.efghi.
     Aerator replacement components that begin with A or 0 do not follow the numbering
    scheme. The part number is individual. 
    B  - Neoperl North America
    R  - Retail
    x  - Assembly stage
         1   - Aerator
         2   - Insert with dome screen
         3   - Insert without dome
         9   - Vandal proof aerator
         B   - Unassembled aerator
         C   - Vandal proof aerator with hose guard
         E   - Aerator with adapter
         F   - Cachè
         V** - Components
         W** - Washer
         X*  - Adapters/couplers/swivels
    a  - Product type
         0 - Void
         1 - Perlator
         2 - Perlator Jr.
         3 - Cascade
         4 - NEOPERL - LL
         6 - Spray
         7 - Care (laminar)
         A - Spring flo 
         B - Spring flo Jr.   
         C - Perlator/short
         D - Perlator laminar Jr.
         E - Perlator Tom Thumb 
         F - Laminar Tom Thumb 
         G - R O coupler
         H - Spray Jr.
         L - Perlator laminar
         M - Careguard
         S - SLC aerator
    b  - Flow rate
         0 - Void
         1 - 1.5 gpm
         2 - 2.0 gpm
         3 - 2.2 gpm
         4 - 3.0 gpm
         5 - PCA 0.5 gpm (1,7 L)
         6 - PCA 1.0 gpm (3,5 L)
         7 - PCA 1.5 gpm (5,0 L)
         8 - PCA 2.2 gpm (8,3 L)
         9 - FF (full-flow)
         A - Class A
         B - Class B
         C - Class C
         D - Class D
         E - Class U
         F - Class Z
         G - 3.5 gpm
         H - Class M
         J - PCA 8.0 L
         K - 4.0 gpm
         L - Max flow
         M - 4.5 gpm
         N - 1.0 gpm
         Q - PCA .66 gpm (2,5 L)
         R - PCA 1.75 gpm (6,0 L)
    c  - Housing thread (letter or number representing housing thread)
    d  - Finish/color (letter or number representing finish/color)
    1  - Place holder (constant)
    e  - Washer # 
         0 - Void
         1 - BW.7134.1 (lg .072)
         2 - BW.7134.1 (lg .072)
         3 - BW.7110.1 (lg .095)
         4 - BW.7110.1 (lg .095)
         5 - BW.7411.1 (lg .125)
         6 - BW.5065.1 & BW.7134.1 (dt .075)
         7 - BW.5065.1 & BW.7134.1 (dt .075)
         8 - BW.7129.1 (jr. PCA .125)
         9 - BW.7476.1 (jr .125)
         A - BW.6313.1 (jr .144)
         B - BW.7102.1 (jr. PCA .144)
         C - BV.6217.1 lg. spring flo
         D - BW.0002.1 (.828 santoprene)
         E - BV.6230.1 sm. spring flo
         F - BW.6309.1 (jr. .062)
         G - 55.1149.1 (TT .110)
         H - 55.1148.1 (TT .060)
         J - BW.0003.1 (Chicago fct)
         K - BW.0005.1
         L - BW.0006.1
         M - 55.1252.1 (M28)  
    fg - Marking (letters and numbers respresenting marking)
    h  - Packaging (letter or number representing packaging)
    i  - Customer name (letter representing customer labeling)
    *  - Random numbers  
         a - Product type
         b - Flow rate
         c - Housing tread
    ** - Random numbers
         a - Product type
         b - Flow rate
         c - Housing tread
         d - Finsh/color
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

[1] All aerators, faucet end attachments, snap fittings, and couplers are designated
    according to one of the following numbering schemes: Bx.abcd.1.efghi or Rx.abcd.1.efghi.
     Aerator replacement components that begin with A or 0 do not follow the numbering
    scheme. The part number is individual. 
    B  - Neoperl North America
    R  - Retail
    x  - Assembly stage
         1   - Aerator
         2   - Insert with dome screen
         3   - Insert without dome
         9   - Vandal proof aerator
         B   - Unassembled aerator
         C   - Vandal proof aerator with hose guard
         E   - Aerator with adapter
         F   - Cachè
         V** - Components
         W** - Washer
         X*  - Adapters/couplers/swivels
    a  - Product type
         0 - Void
         1 - Perlator
         2 - Perlator Jr.
         3 - Cascade
         4 - NEOPERL - LL
         6 - Spray
         7 - Care (laminar)
         A - Spring flo 
         B - Spring flo Jr.   
         C - Perlator/short
         D - Perlator laminar Jr.
         E - Perlator Tom Thumb 
         F - Laminar Tom Thumb 
         G - R O coupler
         H - Spray Jr.
         L - Perlator laminar
         M - Careguard
         S - SLC aerator
    b  - Flow rate
         0 - Void
         1 - 1.5 gpm
         2 - 2.0 gpm
         3 - 2.2 gpm
         4 - 3.0 gpm
         5 - PCA 0.5 gpm (1,7 L)
         6 - PCA 1.0 gpm (3,5 L)
         7 - PCA 1.5 gpm (5,0 L)
         8 - PCA 2.2 gpm (8,3 L)
         9 - FF (full-flow)
         A - Class A
         B - Class B
         C - Class C
         D - Class D
         E - Class U
         F - Class Z
         G - 3.5 gpm
         H - Class M
         J - PCA 8.0 L
         K - 4.0 gpm
         L - Max flow
         M - 4.5 gpm
         N - 1.0 gpm
         Q - PCA .66 gpm (2,5 L)
         R - PCA 1.75 gpm (6,0 L)
    c  - Housing thread (letter or number representing housing thread)
    d  - Finish/color (letter or number representing finish/color)
    1  - Place holder (constant)
    e  - Washer # 
         0 - Void
         1 - BW.7134.1 (lg .072)
         2 - BW.7134.1 (lg .072)
         3 - BW.7110.1 (lg .095)
         4 - BW.7110.1 (lg .095)
         5 - BW.7411.1 (lg .125)
         6 - BW.5065.1 & BW.7134.1 (dt .075)
         7 - BW.5065.1 & BW.7134.1 (dt .075)
         8 - BW.7129.1 (jr. PCA .125)
         9 - BW.7476.1 (jr .125)
         A - BW.6313.1 (jr .144)
         B - BW.7102.1 (jr. PCA .144)
         C - BV.6217.1 lg. spring flo
         D - BW.0002.1 (.828 santoprene)
         E - BV.6230.1 sm. spring flo
         F - BW.6309.1 (jr. .062)
         G - 55.1149.1 (TT .110)
         H - 55.1148.1 (TT .060)
         J - BW.0003.1 (Chicago fct)
         K - BW.0005.1
         L - BW.0006.1
         M - 55.1252.1 (M28)  
    fg - Marking (letters and numbers respresenting marking)
    h  - Packaging (letter or number representing packaging)
    i  - Customer name (letter representing customer labeling)
    *  - Random numbers  
         a - Product type
         b - Flow rate
         c - Housing tread
    ** - Random numbers
         a - Product type
         b - Flow rate
         c - Housing tread
         d - Finsh/color

Diverters BU.1009.1[G]

[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

End Point Control Valves[G] 31.2231.0 FR-CV13 3,0L 31.2232.0 FR-CV13 4,0 31.2233.0 FR-CV13 5,0 31.2234.0 FR-CV13 6,0L 31.2235.0 FR-CV13 7,0L 31.2236.0 FR-CV13 8,0 31.2237.0 FR-CV13 9,0L 31.2239.0 FR-CV13 12,0L

[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Miscellaneous Faucet Components[1] 07.8152.0 VARIO T5 PCR 1.5gpm f.55/64 Chrome plated 07.8154.0 VARIO T5 PCR 1.5gpm f.55/64 White BX.0503.1 On/Off Adapter BX.3313.1.0001 Universal Adapter Bx.abcd.1.efghi GS.10PK.1.0001 Adapter in Low Lead Swivel[G] GS.10Q3.1.0001 Adapter in Low Lead Swivel[G] GX.0433.1.0000 Adapter 1/2[G] GX.0443.1.0001 Adapter, Low Lead - 15/16-27 Male x 55/64-27 Male[G] GX.0503.1 On/Off Adapter[G] GX.050G.1 On/Off Adapter[G] GX.0583.1.0001 Adapter, Low Lead - 1/2-14 NPT Female x 55/64-27 M[G] GX.0603.1.0001 Adapter, Low Lead - 55/64-27 Male x 55/64-27 F[G] GX.3223.1.0001,Snap Fitting PL-HC-FF Insert Chrome Plated, Low Lead Dual Thread[G] GX.3233.1.0001,Snap Fitting PL-HC-FF Insert Chrome Plated, Low Lead Dual Thread[G] GX.3313.1.0001[G] GX.3323.1.0001 Adapter, Low Lead 9/16-24 Male x 55/64-27 Male[G] GX.3363.1.0001 Adapter, Low Lead 15/16-27 Male x 55/64-27 Male[G] GX.3373.1.0001 Adapter, Low Lead Chrome Plated 3/8-18 NPSM x 55/64-27 Male[G] GX.3393.1.0001 Adapter, Low Lead 13/16-27 Male x 55/64-27 Male[G] GX.3413.1.0001 Adapter, Low Lead 3/4-27 Female x 55/64-27 Male[G] GX.3423.1.0001 Adapter, Low Lead 15-16-27M x 55/64-27M x 3/4-11.5 M[G] GX.3443.1.0001 Adapter, Low Lead 11/16-27 Male x 55/64-27 Male[G] GX.3453.1.0001 Adapter, Low Lead 3/4-11.5 NH Female Hose x 55/64-27 Male[G] GX.3463.1.0001 Adapter, Low Lead 3/4-11.5 NH Male Hose x 55/64-27 Female[G] GX.3483.1.0001 Adapter, Low Lead 3/4-11.5 NH Male Hose x Dual Thread[G] GX.3493.1.0001 Adapter 13/16-24 Female x 55/64-27 Male[G] GX.3593.1.0001 Adapter Long, Low Lead 13/16-27 Male x 55/64-27 Male[G] GX.3623.1.0001 Adapter 3/8-18 NPT x 55/64-27 Male[G] GX.3693.1.0001 Adapter, Low Lead 13/16-24 Female x 3/4-27 Male Without Knurl[G] GX.3783.1.0001 Shower Adapter Chrome Plated 1/2-14 NPT Male & Female[G] GX.3873.1.0000 Adapter, Low Lead 55/64-27 Male x M22x1-6H x M24x1-6g[G] GY.0433.1.0000 Adapter 1/2[G] GY.0443.1.0000 Adapter, Low Lead - 15/16 Male x 55/64 Female[G] GY.0583.1.0000 Adapter, Low Lead - 1/2-14 NPT Female[G] GY.0593.1.0000 Adapter Housing[G] GY.0603.1.0000 Adapter Housing 55/64-27 Male x 55/64-27 F[G] GY.3223.1.0000 Housing, Snap Fitting Dual Thread[G] GY.3233.1.0000 Snap Fitting Housing[G] GY.3253.1.0000 Housing, Snap Fitting[G] GY.3323.1.0000 Adapter 9/16 Male x 55/64 Male[G] GY.3363.1.0000 Adapter Housing 15/16 Male x 55/64 Male[G] GY.3373.1.0000 Adapter 3/8 NPT x 15/16 Male[G] GY.3393.1.0000 Adapter Housing 13/16 Male x 55/64 Male[G] GY.3413.1.0000 Adapter Housing 3/4 Female x 55/64 Male[G] GY.3423.1.0000 Adapter Housing[G] GY.3443.1.0000 Adapter Body[G] GY.3453.1.0000 Adapter 3/4 Female Hose x 55/64 Male[G] GY.3463.1.0000 Adapter Housing 3/4 Male Hose x 55/64 Female[G] GY.3483.1.0000 Adapter 3/4 Male Hose x Dual Thread[G] GY.3493.1.0000 Adapter 13/16 Female x 55/64 Male[G] GY.3593.1.0000 Adapter 13/16 Female x 55/64 Male[G] GY.3623.1.0000 Adapter Housing 3/8-18 x 55/64 Male[G] GY.3693.1.0000 Adapter Housing 13/16-24 Female x 3/4-27 Male[G] GY.3783.1.0000 Adapter Housing 1/2-14 NPT Male & Female[G] GY.3873.1.0000 Adapter M24x1, M22x1 X 55/64 Male[G] Rx.abcd.1.efghi

[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

[1] All aerators, faucet end attachments, snap fittings, and couplers are designated
    according to one of the following numbering schemes: Bx.abcd.1.efghi or Rx.abcd.1.efghi.
     Aerator replacement components that begin with A or 0 do not follow the numbering
    scheme. The part number is individual. 
    B  - Neoperl North America
    R  - Retail
    x  - Assembly stage
         1   - Aerator
         2   - Insert with dome screen
         3   - Insert without dome
         9   - Vandal proof aerator
         B   - Unassembled aerator
         C   - Vandal proof aerator with hose guard
         E   - Aerator with adapter
         F   - Cachè
         V** - Components
         W** - Washer
         X*  - Adapters/couplers/swivels
    a  - Product type
         0 - Void
         1 - Perlator
         2 - Perlator Jr.
         3 - Cascade
         4 - NEOPERL - LL
         6 - Spray
         7 - Care (laminar)
         A - Spring flo 
         B - Spring flo Jr.   
         C - Perlator/short
         D - Perlator laminar Jr.
         E - Perlator Tom Thumb 
         F - Laminar Tom Thumb 
         G - R O coupler
         H - Spray Jr.
         L - Perlator laminar
         M - Careguard
         S - SLC aerator
    b  - Flow rate
         0 - Void
         1 - 1.5 gpm
         2 - 2.0 gpm
         3 - 2.2 gpm
         4 - 3.0 gpm
         5 - PCA 0.5 gpm (1,7 L)
         6 - PCA 1.0 gpm (3,5 L)
         7 - PCA 1.5 gpm (5,0 L)
         8 - PCA 2.2 gpm (8,3 L)
         9 - FF (full-flow)
         A - Class A
         B - Class B
         C - Class C
         D - Class D
         E - Class U
         F - Class Z
         G - 3.5 gpm
         H - Class M
         J - PCA 8.0 L
         K - 4.0 gpm
         L - Max flow
         M - 4.5 gpm
         N - 1.0 gpm
         Q - PCA .66 gpm (2,5 L)
         R - PCA 1.75 gpm (6,0 L)
    c  - Housing thread (letter or number representing housing thread)
    d  - Finish/color (letter or number representing finish/color)
    1  - Place holder (constant)
    e  - Washer # 
         0 - Void
         1 - BW.7134.1 (lg .072)
         2 - BW.7134.1 (lg .072)
         3 - BW.7110.1 (lg .095)
         4 - BW.7110.1 (lg .095)
         5 - BW.7411.1 (lg .125)
         6 - BW.5065.1 & BW.7134.1 (dt .075)
         7 - BW.5065.1 & BW.7134.1 (dt .075)
         8 - BW.7129.1 (jr. PCA .125)
         9 - BW.7476.1 (jr .125)
         A - BW.6313.1 (jr .144)
         B - BW.7102.1 (jr. PCA .144)
         C - BV.6217.1 lg. spring flo
         D - BW.0002.1 (.828 santoprene)
         E - BV.6230.1 sm. spring flo
         F - BW.6309.1 (jr. .062)
         G - 55.1149.1 (TT .110)
         H - 55.1148.1 (TT .060)
         J - BW.0003.1 (Chicago fct)
         K - BW.0005.1
         L - BW.0006.1
         M - 55.1252.1 (M28)  
    fg - Marking (letters and numbers respresenting marking)
    h  - Packaging (letter or number representing packaging)
    i  - Customer name (letter representing customer labeling)
    *  - Random numbers  
         a - Product type
         b - Flow rate
         c - Housing tread
    ** - Random numbers
         a - Product type
         b - Flow rate
         c - Housing tread
         d - Finsh/color

Facility : Fujan, China

Mechanical Plumbing Devices

	Trade Designation
Faucet Aerator
	W245 Bubble Stream Swivel Spray D/T CP
	W248B-25 Swivel Spray 2.5 D/T
	W249 Bubble Stream Swivel Spray D/T CP, Plastic Hsg / Brass Connector
	W250 Bubble Stream Swivel Spray D/T BN, Plastic Hsg / Brass Connector
	W261 Bubble Stream Classic 1.5 Double Swivel, Plastic
	W275 Bubble Stream Soft Grip 2.2, Dumbell Swivel, Brass Connector
	W276 Bubble Stream Soft Grip 2.2, Dumbell Swivel, Plastic Connector
	W279 Bubble Stream Soft Grip 1.5, Dumbell Swivel, Brass Connector
	W280 Bubble Stream Soft Grip 1.5, Dumbell Swivel, Plastic Connector
	W284 Bubble Stream Classic 1.5, Dumbell Swivel, Brass Connector W/CP
	W285 Bubble Stream Classic 1.5, Dumbell Swivel, Brass Connector B/CP
	W286 Bubble Stream Classic 1.5, Dumbell Swivel, Plastic Connector W/CP
	W287 Bubble Stream Classic 2.2, Dumbell Swivel, Brass Connector W/CP
	W288 Bubble Stream Classic 2.2, Dumbell Swivel, Brass Connector B/CP
	W289 Bubble Stream Classic 2.2, Dumbell Swivel, Plastic Connector W/CP
	W290 Bubble Stream Classic 1.5, Dumbell Swivel, Plastic Connector B/CP
	W291 Bubble Stream Classic 2.2, Dumbell Swivel, Plastic Connector B/CP
	W292 Bubble Stream Soft Grip FF M22 Single Swivel, Brass Connector

Facility : Jiangmen, Guangdong Province, China

Mechanical Plumbing Devices

	Trade Designation
Flexible Plumbing Connectors
	39.ABCD.EFG.HI Neoperl Neoflex SPX Flexible Hose Connectors[1] [8] [10]
	39.ABCD.EFG.HI Neoperl Neoflex SPX Flexible Hose Connectors[1] [8] [9]
[1] Maximum length of hose is 78". [8] Sizes associated with this trade name: DN13, DN10, DN8, DN6 Naming convention: A – May be 0-4 B – (0) SPX hose material CD.EFG – Any number HI – Packaging information [9] Fittings associated with this trade name: DN13 C Fitting groove 1/2 m DR DN13 C Assy ORG 1/2 F A/F24 DR DN13 C Fitting R1/2 m A/F22 DR DN10 Assy RWG 1/2 F A/F24 DN10 Assy RWG 3/4 F A/F30 DN10 Assy RWG elbow 1/2 F A/F24 DN10 Assy RWG elbow 3/4 F A/F30 DN10 Fitting 1/2 m A/F21 DN10 Fitting 3/4 m A/F27 DN10 Fitting tube D12 A/F13 DN8 Assy revolving 3/8 f A/F19 fiber DN8 Assy RWG 3/8 f A/F19 DN8 Assy RWG 1/2 f A/F24 DN8 Assy RWG 3/4 f A/F30 DN8 Assy M10x1 S m A/F11 DN8 Assy M10x1 L m A/F11 DN8 Assy M10x1 XL m A/F11 DN8 Assy RWG elbow 3/8f A/F19 DN8 C Assy M10x1 XL m A/F11 DN8 Assy RWG elbow 3/8f A/F19 DN8 Assy RWG elbow 1/2 f A/F24 DN8 Assy RWG elbow 3/4 f A/F30 DN8 Assy Compression fitting D10 3/8 A/F19 DN8 Assy compression fitting D8 3/8 A/F19 DN8 fitting 1/2 m A/F21 DN8 Fitting tube A10 A/F11 DN6 Assy RWG 3/8 f A/F19 DN6 Assy 1/2 f A/F24 fiber DN6 Assy M10x1 S m A/F11 DN6 Assy M10x1 L m A/F11 DN6 Assy M8x1 S m A/F10 DN6 Assy M10x1 XL m A/F11 DN6 fitting tube D8 A/F10 DN6 fitting tube D10 A/F11 [10] Fittings associated with this trade name: DN6 Assy RWG 3/8 f A/F19 DN6 Assy 1/2 f A/F24 fiber DN6 Assy M10x1 S m A/F11 DN6 Assy M10x1 L m A/F11 DN6 Assy M8x1 S m A/F10 DN6 Assy M10x1 XL m A/F11 DN6 Fitting tube D8 A/F10 DN6 Fitting tube D10 A/F11 DN8 Assy revolving 3/8 f A/F19 fiber DN8 Assy RWG 3/8 f A/F19 DN8 Assy RWG 1/2 f A/F24 DN8 Assy RWG 3/4 f A/F30 DN8 Assy M10x1 S m A/F11 DN8 Assy M10x1 L m A/F11 DN8 Assy M10x1 XL m A/F11 DN8 C Assy M10x1 XL m A/F11 DN8 C fitting M10x1 S m DN8 Assy RWG elbow 3/8f A/F19 DN8 Assy RWG elbow 1/2 f A/F24 DN8 Assy RWG elbow 3/4 f A/F30 DN8 Assy Compression fitting D10 3/8 A/F19 DN8 Assy Compression fitting D8 3/8 A/F19 DN8 Fitting 1/2 m A/F21 DN8 Fitting 1/2 m A/F21 DR DN8 Fitting tube A10 A/F11 DN8 Fitting tube D10 A/F11 DN8 C fitting tube M10x1 m DR DN10 Assy RWG 1/2 F A/F24 DN10 Assy RWG 3/4 F A/F30 DN10 Assy RWG elbow 1/2 F A/F24 DN10 Assy RWG elbow 3/4 F A/F30 DN10 Fitting 1/2 m A/F21 DN10 Fitting 3/4 m A/F27 DN10 Fitting tube D12 A/F13 DN13 C Fitting groove 1/2 m DR DN13 C Assy ORG 1/2 F A/F24 DR DN13 C Fitting R1/2 m A/F22 DR DN6 Fitting tube D8 A/F10 DN6 Fitting tube D10 A/F11
Faucet, Pull-Out Hose Assembly
	39.86CD.EFG.HI Neoflex CRG[2] [3] [4] [5]
	39.86CD.EFG.HI Neoflex CRG[2] [4] [6] [7] [G]
	39.86CD.EFG.HI Neoflex CRG[1] [2] [3] [4] [G]
[1] Maximum length of hose is 78". [2] Size evaluated with this trade name: DN8 CD.EFG.HI may be any alpha numeric value [3] Fitting evaluated with this trade name: MH CRG D8.5 Fitting 1/2 MH CRG D8.5 Fitting M15x1 A/F 1/2 [4] Gaskets and o-rings have not been evaluated. [5] Hose length is less than 43". [6] Hose length must be between 43" and 78". [7] Fitting evaluated with this trade name: MH CRG D8.5 Fitting 1/2 MH CRG D8.5 Fitting M15x1 A/F 1/2 MH CRG D8.3 Fitting 9/16-12UNC-2A [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Facility : Shanghai, China

Mechanical Plumbing Devices

	Trade Designation
Aerators[1]
	B1.1107.1.efghi[G]
	B1.1207.1.efghi[G]
	B1.1307.1.efghi[G]
	B1.1407.1.efghi[G]
	B1.1707.1.efghi[G]
	B1.1807.1.efghi[G]
	B1.1907.1.efghi[G]
	B1.1G07.1.efghi[G]
	B1.1K07.1.efghi[G]
	B1.1M07.1.efghi[G]
	B1.1N07.1.efghi[G]
	B1.2107.1.efghi[G]
	B1.2207.1.efghi[G]
	B1.2307.1.efghi[G]
	B1.2707.1.efghi[G]
	B1.2807.1.efghi[G]
	B1.2907.1.efghi[G]
	B1.2M07.1.efghi[G]
	B1.2N07.1.efghi[G]
	B1.D107.1.efghi[G]
	B1.D204.1.efghi[G]
	B1.D307.1.efghi[G]
	B1.D707.1.efghi[G]
	B1.D807.1.efghi[G]
	B1.D907.1.efghi[G]
	B1.DN07.1.efghi[G]
	B9.1107.1.efghi[G]
	B9.1207.1.efghi[G]
	B9.1307.1.efghi[G]
	B9.1407.1.efghi[G]
	B9.1707.1.efghi[G]
	B9.1807.1.efghi[G]
	B9.1G07.1.efghi[G]
	B9.1K07.1.efghi[G]
	B9.1M07.1.efghi[G]
	B9.1N07.1.efghi[G]
	B9.2107.1.efghi[G]
	B9.2207.1.efghi[G]
	B9.2307.1.efghi[G]
	B9.2707.1.efghi[G]
	B9.2807.1.efghi[G]
	B9.2907.1.efghi[G]
	B9.2M07.1.efgh[G]
	B9.2N07.1.efghi[G]
	B9.D107.1.efghi[G]
	B9.D204.1.efghi[G]
	B9.D307.1.efghi[G]
	B9.D707.1.efghi[G]
	B9.D807.1.efghi[G]
	B9.D907.1.efghi[G]
	B9.DN07.1.efghi[G]
	Bx.abcd.1.efghi Cascade Flow Restricting Aerators[G]
	Bx.abcd.1.efghi PCA Cascade Aerators[G]
	Bx.abcd.1.efghi PCA Spray Laminar Aerators[G]
	Bx.abcd.1.efghi Perlator TT Aerated Flow Aerators[G]
	Bx.abcd.1.efghi Perlator TT Laminar Flow Aerators[G]
	Bx.abcd.1.efghi Spring-Flo Aerators
	DEAL #40E
	Deal #38D
	Rx.abcd.1.efghi Cascade Flow Restricting Aerators[G]
	Rx.abcd.1.efghi PCA Cascade Aerators[G]
	Rx.abcd.1.efghi PCA Spray Laminar Aerators[G]
	Rx.abcd.1.efghi Perlator TT Aerated Flow Aerators[G]
	Rx.abcd.1.efghi Perlator TT Laminar Flow Aerators[G]
	Rx.abcd.1.efghi Spring-Flo Aerators
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
[1] All aerators, faucet end attachments, snap fittings, and couplers are designated according to one of the following numbering schemes: Bx.abcd.1.efghi or Rx.abcd.1.efghi. Aerator replacement components that begin with A or 0 do not follow the numbering scheme. The part number is individual. B - Neoperl North America R - Retail x - Assembly stage 1 - Aerator 2 - Insert with dome screen 3 - Insert without dome 9 - Vandal proof aerator B - Unassembled aerator C - Vandal proof aerator with hose guard E - Aerator with adapter F - Cachè V - Components W - Washer X* - Adapters/couplers/swivels a - Product type 0 - Void 1 - Perlator 2 - Perlator Jr. 3 - Cascade 4 - NEOPERL - LL 6 - Spray 7 - Care (laminar) A - Spring flo B - Spring flo Jr. C - Perlator/short D - Perlator laminar Jr. E - Perlator Tom Thumb F - Laminar Tom Thumb G - R O coupler H - Spray Jr. L - Perlator laminar M - Careguard S - SLC aerator b - Flow rate 0 - Void 1 - 1.5 GPM 2 - 2.0 GPM 3 - 2.2 GPM 4 - 3.0 GPM 5 - PCA 0.5 GPM (1,7 L) 6 - PCA 1.0 GPM (3,5 L) 7 - PCA 1.5 GPM (5,0 L) 8 - PCA 2.2 GPM (8,3 L) 9 - FF (full-flow) A - Class A B - Class B C - Class C D - Class D E - Class U F - Class Z G - 3.5 GPM H - Class M J - PCA 8.0 L K - 4.0 GPM L - Max flow M - 4.5 GPM N - 1.0 GPM Q - PCA .66 GPM (2,5 L) R - PCA 1.75 GPM (6,0 L) c - Housing thread (letter or number representing housing thread) d - Finish/color (letter or number representing finish/color) 1 - Place holder (constant) e - Washer # 0 - Void 1 - BW.7134.1 (lg .072) 2 - BW.7134.1 (lg .072) 3 - BW.7110.1 (lg .095) 4 - BW.7110.1 (lg .095) 5 - BW.7411.1 (lg .125) 6 - BW.5065.1 & BW.7134.1 (dt .075) 7 - BW.5065.1 & BW.7134.1 (dt .075) 8 - BW.7129.1 (jr. PCA .125) 9 - BW.7476.1 (jr .125) A - BW.6313.1 (jr .144) B - BW.7102.1 (jr. PCA .144) C - BV.6217.1 lg. spring flo D - BW.0002.1 (.828 santoprene) E - BV.6230.1 sm. spring flo F - BW.6309.1 (jr. .062) G - 55.1149.1 (TT .110) H - 55.1148.1 (TT .060) J - BW.0003.1 (Chicago fct) K - BW.0005.1 L - BW.0006.1 M - 55.1252.1 (M28) fg - Marking (letters and numbers respresenting marking) h - Packaging (letter or number representing packaging) i - Customer name (letter representing customer labeling) * - Random numbers a - Product type b - Flow rate c - Housing tread ** - Random numbers a - Product type b - Flow rate c - Housing tread d - Finsh/colorD)
Aerator Replacement Components[1]
	02.5601.0[G]
	02.5603.0[G]
	02.5607.1[G]
	02.5608.0[G]
	02.5611.0[G]
	02.5613.0[G]
	02.5614.0[G]
	02.5617.0[G]
	02.5618.0[G]
	02.8201.0[G]
	02.8301.0[G]
	02.8311.0[G]
	02.8321.0[G]
	02.8351.0[G]
	A5.4130.0[G]
	A5.4132.0[G]
	A5.4143.0[G]
	A5.4145.0[G]
	A5.4146.0[G]
	A5.4160.0[G]
	A5.4162.0[G]
	A5.4163.0[G]
	A5.4165.0[G]
	A5.4166.0[G]
	A5.9035.1[G]
	A5.9036.1[G]
	A5.9042.1[G]
	A5.9043.1[G]
	A5.9044.1[G]
	A5.9045.1[G]
	A5.9046.1[G]
	Bx.abcd.1.efghi
	Rx.abcd.1.efghi
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
[1] All aerators, faucet end attachments, snap fittings, and couplers are designated according to one of the following numbering schemes: Bx.abcd.1.efghi or Rx.abcd.1.efghi. Aerator replacement components that begin with A or 0 do not follow the numbering scheme. The part number is individual. B - Neoperl North America R - Retail x - Assembly stage 1 - Aerator 2 - Insert with dome screen 3 - Insert without dome 9 - Vandal proof aerator B - Unassembled aerator C - Vandal proof aerator with hose guard E - Aerator with adapter F - Cachè V - Components W - Washer X* - Adapters/couplers/swivels a - Product type 0 - Void 1 - Perlator 2 - Perlator Jr. 3 - Cascade 4 - NEOPERL - LL 6 - Spray 7 - Care (laminar) A - Spring flo B - Spring flo Jr. C - Perlator/short D - Perlator laminar Jr. E - Perlator Tom Thumb F - Laminar Tom Thumb G - R O coupler H - Spray Jr. L - Perlator laminar M - Careguard S - SLC aerator b - Flow rate 0 - Void 1 - 1.5 GPM 2 - 2.0 GPM 3 - 2.2 GPM 4 - 3.0 GPM 5 - PCA 0.5 GPM (1,7 L) 6 - PCA 1.0 GPM (3,5 L) 7 - PCA 1.5 GPM (5,0 L) 8 - PCA 2.2 GPM (8,3 L) 9 - FF (full-flow) A - Class A B - Class B C - Class C D - Class D E - Class U F - Class Z G - 3.5 GPM H - Class M J - PCA 8.0 L K - 4.0 GPM L - Max flow M - 4.5 GPM N - 1.0 GPM Q - PCA .66 GPM (2,5 L) R - PCA 1.75 GPM (6,0 L) c - Housing thread (letter or number representing housing thread) d - Finish/color (letter or number representing finish/color) 1 - Place holder (constant) e - Washer # 0 - Void 1 - BW.7134.1 (lg .072) 2 - BW.7134.1 (lg .072) 3 - BW.7110.1 (lg .095) 4 - BW.7110.1 (lg .095) 5 - BW.7411.1 (lg .125) 6 - BW.5065.1 & BW.7134.1 (dt .075) 7 - BW.5065.1 & BW.7134.1 (dt .075) 8 - BW.7129.1 (jr. PCA .125) 9 - BW.7476.1 (jr .125) A - BW.6313.1 (jr .144) B - BW.7102.1 (jr. PCA .144) C - BV.6217.1 lg. spring flo D - BW.0002.1 (.828 santoprene) E - BV.6230.1 sm. spring flo F - BW.6309.1 (jr. .062) G - 55.1149.1 (TT .110) H - 55.1148.1 (TT .060) J - BW.0003.1 (Chicago fct) K - BW.0005.1 L - BW.0006.1 M - 55.1252.1 (M28) fg - Marking (letters and numbers respresenting marking) h - Packaging (letter or number representing packaging) i - Customer name (letter representing customer labeling) * - Random numbers a - Product type b - Flow rate c - Housing tread ** - Random numbers a - Product type b - Flow rate c - Housing tread d - Finsh/colorD)
End Point Control Valves[2]
	31.4201.0.efgh Check Valve OD8/DN6
[2] e - Washer # (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F, G, H, J, K, L, or M) fg - Marking (2-digit numeric or alpha-numeric designation) h - Packaging (1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, or D)
Miscellaneous Faucet Components[1]
	Bx.abcd.1.efghi Faucet Spout End Attachments
	Rx.abcd.1.efghi Faucet Spout End Attachements
[1] All aerators, faucet end attachments, snap fittings, and couplers are designated according to one of the following numbering schemes: Bx.abcd.1.efghi or Rx.abcd.1.efghi. Aerator replacement components that begin with A or 0 do not follow the numbering scheme. The part number is individual. B - Neoperl North America R - Retail x - Assembly stage 1 - Aerator 2 - Insert with dome screen 3 - Insert without dome 9 - Vandal proof aerator B - Unassembled aerator C - Vandal proof aerator with hose guard E - Aerator with adapter F - Cachè V - Components W - Washer X* - Adapters/couplers/swivels a - Product type 0 - Void 1 - Perlator 2 - Perlator Jr. 3 - Cascade 4 - NEOPERL - LL 6 - Spray 7 - Care (laminar) A - Spring flo B - Spring flo Jr. C - Perlator/short D - Perlator laminar Jr. E - Perlator Tom Thumb F - Laminar Tom Thumb G - R O coupler H - Spray Jr. L - Perlator laminar M - Careguard S - SLC aerator b - Flow rate 0 - Void 1 - 1.5 GPM 2 - 2.0 GPM 3 - 2.2 GPM 4 - 3.0 GPM 5 - PCA 0.5 GPM (1,7 L) 6 - PCA 1.0 GPM (3,5 L) 7 - PCA 1.5 GPM (5,0 L) 8 - PCA 2.2 GPM (8,3 L) 9 - FF (full-flow) A - Class A B - Class B C - Class C D - Class D E - Class U F - Class Z G - 3.5 GPM H - Class M J - PCA 8.0 L K - 4.0 GPM L - Max flow M - 4.5 GPM N - 1.0 GPM Q - PCA .66 GPM (2,5 L) R - PCA 1.75 GPM (6,0 L) c - Housing thread (letter or number representing housing thread) d - Finish/color (letter or number representing finish/color) 1 - Place holder (constant) e - Washer # 0 - Void 1 - BW.7134.1 (lg .072) 2 - BW.7134.1 (lg .072) 3 - BW.7110.1 (lg .095) 4 - BW.7110.1 (lg .095) 5 - BW.7411.1 (lg .125) 6 - BW.5065.1 & BW.7134.1 (dt .075) 7 - BW.5065.1 & BW.7134.1 (dt .075) 8 - BW.7129.1 (jr. PCA .125) 9 - BW.7476.1 (jr .125) A - BW.6313.1 (jr .144) B - BW.7102.1 (jr. PCA .144) C - BV.6217.1 lg. spring flo D - BW.0002.1 (.828 santoprene) E - BV.6230.1 sm. spring flo F - BW.6309.1 (jr. .062) G - 55.1149.1 (TT .110) H - 55.1148.1 (TT .060) J - BW.0003.1 (Chicago fct) K - BW.0005.1 L - BW.0006.1 M - 55.1252.1 (M28) fg - Marking (letters and numbers respresenting marking) h - Packaging (letter or number representing packaging) i - Customer name (letter representing customer labeling) * - Random numbers a - Product type b - Flow rate c - Housing tread ** - Random numbers a - Product type b - Flow rate c - Housing tread d - Finsh/colorD)

Facility : Randers, Denmark

Mechanical Plumbing Devices

	Trade Designation
Flexible Plumbing Connectors
	38.aa.bb.ccc.dd NEOPERL NEOFLEX SPX Flexible Hose Connectors[1]
	39.ABCD.EFG.HI Neoperl Neoflex SPX Flexible Hose Connectors[2] [3] [4]
[1] All flexible hose connectors are designated according to the following numbering scheme: 38.aa.bb.ccc.dd, where 38 - Neoperl Neoflex SPX flexible connection hose aa - Hose diameter 06mm - (hose type) 58, 59, 78, 79 08mm - (hose type) 60, 61, 62, 63, 64, 65, 70, 71, 72, 73, 80, 81, 82 10mm - (hose type) 83, 84, 85 13mm - (hose type) 76, 86, 88, 89 Customer specific (not related to DN, but restricted to maximum inner diameter of 13mm) - (hose type) 99 bb - Hose end fitting combination Diameter 06mm Hose types - 58, 59, 78, 79 (hose end fitting combinations) 01-6, 14-18, 26-29, 37-39, 47-48, 56 Diameter 08mm Hose types - 60, 63, 70, 80 (hose end fitting combinations) 01-18, 24-40, 46-61, 67-81, 87-99 Hose types - 61, 64, 71, 81 (hose end fitting combinations) 00, 06-18, 24-35, 41-51, 57-66, 72-80, 86-93, 99 Hose types - 62, 65, 72, 82 (hose end fitting combinations) 00-05, 11-16, 22-26, 32-35, 41-43, 49, 50, 56 Hose type - 73 (hose end fitting combinations) 1, 2, 5, 14, 17, 47 Diameter 10mm Hose types - 83, 84, 85 (hose end fitting combinations) 01-07, 14-19, 26-30, 47-49, 56, 57, 64 Diameter 13mm Hose Types - 76, 86, 88, 89 (hose end fitting combinations) 01-06, 14-18, 26-29, 27-39, 47, 48, 56 ccc - Hose length in cm (any 3-digit numeric code up to 200 cm) dd - Packaging options (any 2-digit numeric code) [2] Sizes approved with this trade name: DN6, DN8, DN10, and DN13. Naming convention: A – May be 0-4 B – (0) SPX hose material CD.EFG – Any number HI – Packaging information [3] Fittings approved with this trade name: DN6 Assy RWG 3/8 f A/F19 DN6 Assy 1/2 f A/F24 fiber DN6 Assy M10x1 S m A/F11 DN6 Assy M10x1 L m A/F11 DN6 Assy M8x1 S m A/F10 DN6 Assy M10x1 XL m A/F11 DN6 Fitting tube D8 A/F10 DN6 Fitting tube D10 A/F11 DN8 Assy revolving 3/8 f A/F19 fiber DN8 Assy RWG 3/8 f A/F19 DN8 Assy RWG 1/2 f A/F24 DN8 Assy RWG 3/4 f A/F30 DN8 Assy M10x1 S m A/F11 DN8 Assy M10x1 L m A/F11 DN8 Assy M10x1 XL m A/F11 DN8 C Assy M10x1 XL m A/F11 DN8 C fitting M10x1 S m DN8 Assy RWG elbow 3/8f A/F19 DN8 Assy RWG elbow 1/2 f A/F24 DN8 Assy RWG elbow 3/4 f A/F30 DN8 Assy Compression fitting D10 3/8 A/F19 DN8 Assy Compression fitting D8 3/8 A/F19 DN8 Fitting 1/2 m A/F21 DN8 Fitting 1/2 m A/F21 DR DN8 Fitting tube A10 A/F11 DN8 Fitting tube D10 A/F11 DN8 C fitting tube M10x1 m DR DN10 Assy RWG 1/2 F A/F24 DN10 Assy RWG 3/4 F A/F30 DN10 Assy RWG elbow 1/2 F A/F24 DN10 Assy RWG elbow 3/4 F A/F30 DN10 Fitting 1/2 m A/F21 DN10 Fitting 3/4 m A/F27 DN10 Fitting tube D12 A/F13 DN13 C Fitting groove 1/2 m DR DN13 C Assy ORG 1/2 F A/F24 DR DN13 C Fitting R1/2 m A/F22 DR [4] Maximum length of hose is 78".

Facility : Mullheim, Germany

Mechanical Plumbing Devices

	Trade Designation
Aerators
	01.3350.0 NANOPERL-HC-RD-6mm-V[1] [G]
	01.3351.0 NANOPERL-HC-AX-6mm-V[1] [G]
	01.4013.0 NP-LL-IG M22-Z
	01.4023.0 NP-LL-IG M22-A
	01.4053.0 NEOSTRAHL IG M22 HC
	01.4063.0 NEOSTRAHL-ND IG M22
	01.4073.0 NP Lam max. IG M22
	01.4113.0 NP-LL-AG M24-Z
	01.4123.0 NP-LL-AG M24-A
	01.4153.0 NEOSTRAHL AG M24 HC
	01.4163.0 NEOSTRAHL-ND AG M24
	01.4173.0 NP Lam max. AG M24
	01.4603.0 NP-LL-IG M22-U
	01.4703.0 NP-LL-AG M24-U
	01.5001.0 Cachè Honeycomb Std V[G]
	01.5003.0 Cachè Honeycomb Std X[G]
	01.5008.0 Cachè Honeycomb Std PCA[G]
	01.5010.0 Cachè NEOSTRAHL Std[G]
	01.5015.0 Cachè Cascade Std X[G]
	01.5016.0 Cachè Cascade Std Z[G]
	01.5017.0 Cachè Cascade Std A[G]
	01.5018.0 Cachè Cascade Std B[G]
	01.5019.0 Cachè Cascade Std C[G]
	01.5020.0 Cachè Cascade Std D[G]
	01.5032.0 Cachè PCA Spray Std 0,5 gpm[G]
	01.5036.0 Cachè PCA Spray Std 1,0 gpm[G]
	01.5051.0 Cachè Cascade Std PCA 6,0 L[G]
	01.5053.0 Cachè Cascade Std PCA 7,6 L[G]
	01.5054.0 Cachè Cascade Std PCA 8,0 L[G]
	01.5059.0 Cachè Laminar Std PCA 6,0 L[G]
	01.5061.0 Cachè Laminar Std PCA 7,6 L[G]
	01.5062.0 Cachè Laminar Std PCA 8,0 L[G]
	01.5101.0 Cachè Honeycomb Jr V[G]
	01.5103.0 Cachè Honeycomb Jr X[G]
	01.5108.0 Cachè Honeycomb Jr PCA[G]
	01.5111.0 Cachè Laminar Jr V[G]
	01.5113.0 Cachè Laminar Jr X[G]
	01.5118.0 Cachè Laminar Jr PCA[G]
	01.5120.0 Cachè NEOSTRAHL Jr[G]
	01.5132.0 Cachè PCA Spray Jr 0.5 gpm[G]
	01.5136.0 Cachè PCA Spray Jr 1.0 gpm[G]
	01.5151.0 Cachè Honeycomb TT V[G]
	01.5153.0 Cachè Honeycomb TT X[G]
	01.5158.0 Cachè Honeycomb TT PCA[G]
	01.5161.0 Cachè Laminar TT V[G]
	01.5163.0 Cachè Laminar TT X[G]
	01.5168.0 Cachè Laminar TT PCA[G]
	01.5172.0 Cachè Laminar TT Max Flow[G]
	01.5175.0 Cachè NEOSTRAHL TT[G]
	01.5288.0 PERLATOR IT PCA M24x1 2.2 gpm[G]
	01.5331.0 PERLATOR IT V M22x1[G]
	01.5333.0 PERLATOR IT X M22x1[G]
	01.5338.0 PERLATOR IT PCA M22x1 2.2 gpm[G]
	01.5381.0 PERLATOR IT V M24x1[G]
	01.5383.0 PERLATOR IT X M24x1[G]
	01.5501.0 NEOPERL SLIM M18 Dark Grey[G]
	01.5502.0 NEOPERL SLIM M18 Black[G]
	01.5510.0 NEOPERL SLIM M24 GD[G]
	01.5511.0 NEOPERL SLIM M24[G]
	01.5512.0 SLIM SSR M24[G]
	01.7803.0 Cascade M22 x 1 VP Class Z[G]
	01.7813.0 Cascade M22 x 1 VP Class A[G]
	01.7823.0 Cascade M22 x 1 VP Class B[G]
	01.7903.0 Cascade M24 x 1 VP Class Z[G]
	01.7913.0 Cascade M24 x 1 VP Class A[G]
	01.7923.0 Cascade M24 x 1 VP Class B[G]
	01.8303.0 Cascade M22 x 1 Class Z[G]
	01.8313.0 Cascade M22 x 1 Class A[G]
	01.8323.0 Cascade M22 x 1 Class B[G]
	01.8353.0 Cascade M22 x 1 Class X[G]
	01.8403.0 Cascade M24 x 1 Class Z[G]
	01.8413.0 Cascade M24 x 1 Class A[G]
	01.8423.0 Cascade M24 x 1 Class B[G]
	01.8453.0 Cascade M24 x 1 VP Class X[G]
	01.8543.0 Cascade M22 x 1 Class B[G]
	01.8553.0 Cascade M22 x 1 Class C[G]
	01.8563.0 Cascade M22 x 1 Class D[G]
	01.8643.0 Cascade M24 x 1 Class B[G]
	01.8653.0 Cascade M24 x 1 Class C[G]
	01.8663.0 Cascade M24 x 1 Class D[G]
	01.8703.0 CC-SLC M22x1 Class Z[G]
	01.8713.0 CC-SLC M22x1 Class A[G]
	01.8723.0 CC-SLC M22x1 Class B[G]
	01.8803.0 CC-SLC M24x1 Class Z[G]
	01.8813.0 CC-SLC M24x1 Class A[G]
	01.8823.0 CC-SLC M24x1 Class B[G]
	02.3244.0 PL-RC-32x8-C-C-IT[1] [G]
	02.3245.0 PL-RC-32x8 -IT-V[1] [G]
	02.3246.0 PL-RC-40x10 -IT-V[1] [G]
	02.3250.0 PL-RC-24x6 -IT-RS[1] [G]
	02.3251.0 PL-RC-28x7 -IT-RS[1] [G]
	02.3252.0 PL-RC-32x8 -IT-RS[1] [G]
	02.3253.0 PL-RC-40x10 -IT-A-RS[1] [G]
	02.3254.0 PL-RC-40x10 -IT-B-RS[1] [G]
	02.3255.0 PL-RC-40x10 -IT-C-RS[1] [G]
	02.3256.0 PL-RC-32x8 -IT-V-RS[1] [G]
	02.3257.0 PL-RC-40x10 -IT-V-RS[1] [G]
	02.3259.0 PL-RC-40x10 -IT-A[1] [G]
	02.3260.0 PL-RC-40x10 -IT-B[1] [G]
	02.3261.0 PL-RC-40x10 -IT-C[1] [G]
	02.3262.0 PL-RC-40X10-IT-G[1] [G]
	02.3280.0 PL-RC-32x8-IT[1] [G]
	02.3281.0 FS-RC-24X6-IT-LAM[1] [G]
	02.3282.0 PL-RC-24x06-IT[1] [G]
	02.3284.0 PL-RC-28x07-IT[1] [G]
	02.3286.0 FS-RC-38X12-TUB-IT-LAM[1] [G]
	02.3288.0 FS-RC-38x12-TUB-IT-LAM[1] [G]
	02.3289.0 PL-RC-24,5x9 -IT[1] [G]
	02.3291.0 FS-RC-38X12-BASIN-IT-LAM[1] [G]
	02.3293.0 FS-RC-38X12-BASIN-IT-LAM[1] [G]
	02.3295.0 FS-RC-28x7-IT-LAM[1] [G]
	02.3296.0 FS-RC-32x8-IT-LAM[1] [G]
	02.3350.0 NANOPERL-HC-6mm-IT-V[1] [G]
	02.4011.0 NP-LL Insert Class Z
	02.4021.0 NP-LL Insert Class A
	02.4050.0 NEOSTRAHL-ND Insert
	02.4051.0 NEOSTRAHL Insert
	02.4071.0 NP-Lam-Max. IT-max
	02.4601.0 NP-LL Insert Class U
	02.5301.0 PERLATOR IT V Insert[G]
	02.5303.0 PERLATOR IT X Insert[G]
	02.5308.0 PERLATOR IT PCA Insert 2.2 gpm[G]
	02.8301.0 Cascade Insert Class Z[G]
	02.8311.0 Cascade Insert Class A[G]
	02.8321.0 Cascade Insert Class B[G]
	02.8351.0 Cascade Insert Class X[G]
	02.8441.0 Cascade Insert Class B[G]
	02.8451.0 Cascade Insert Class C[G]
	02.8461.0 Cascade Insert Class D[G]
	02.8701.0 CC-SLC Insert ClassZ[G]
	02.8711.0 CC-SLC Insert Class A[G]
	02.8721.0 CC-SLC Insert Class B[G]
	2.3334.010 CACHÉ-HC-JR lam 2.2gpm[3] [G]
	40.0001.000 STD-CC-SLC-IT X 2,2 gpm[G]
	40.0002.000 STD-CC-SLC-IT Z[G]
	40.0003.000 STD-CC-SLC-IT A[G]
	40.0004.000 STD-CC-SLC-IT S[G]
	40.0005.000 STD-CC-SLC-IT B[G]
	40.0006.000 STD-CC-SLC-IT C[G]
	40.0007.000 STD-CC-SLC-IT D[G]
	40.0010.000 STD-CC-SLC-IT T 1.5 gpm[G]
	40.0032.000 CASCADE-SLC-C 1.5gpm[G]
	40.0032.efg Cascade-SLC-C 1.5 gpm[G]
	40.0051.000 STD-CC-SLC-IT-PCA 5,0 L[G]
	40.0052.000 STD-CC-SLC-IT-PCA 6,0 L[G]
	40.0053.000 STD-CC-SLC-IT-PCA 2,2 gpm[G]
	40.0054.000 STD-CC-SLC-IT-PCA 8,0 L[G]
	40.0055.000 STD-CC-SLC-IT PCA 7,0 L[G]
	40.0056.000 STD-CC-SLC-IT PCA 1,5 gpm[G]
	40.0057.000 STD-CC-SLC-IT-PCA 2.0 gpm[G]
	40.0058.000 CC-SLC-STD-IT-PCA 1.0 gpm[G]
	40.0060.000 STD-CC-SLC-IT-PCA 1.25 gpm[G]
	40.0061.000 STD-CC-SLC-IT-PCA 1.75 gpm[G]
	40.0201.010 CACHÉ-CC-SLC-STD X 2,2gpm[G]
	40.0202.010 CACHÉ-CC-SLC-STD Z[G]
	40.0203.010 CACHÉ-CC-SLC-STD A[G]
	40.0204.010 CACHÉ-CC-SLC-STD S[G]
	40.0205.010 CACHÉ-CC-SLC-STD B[G]
	40.0206.010 CACHÉ-CC-SLC-STD C[G]
	40.0207.010 CACHÉ-CC-SLC-STD D[G]
	40.0210.010 CACHÉ-CC-SLC-STD T 1,5gpm[G]
	40.0251.010 CACHÉ-CC-SLC-STD-PCA5,0L[G]
	40.0252.010 CACHÉ-CC-SLC-STD-PCA6,0L[G]
	40.0253.010 CACHÉ-CC-SLC-STD-PCA2,2gpm[G]
	40.0254.010 CACHÉ-CC-SLC-STD-PCA8,0L[G]
	40.0255.010 CACHÉ-CC-SLC-STD-PCA7.0L[G]
	40.0256.010 CACHÉ-CC-SLC-STD-PCA1.5gpm[G]
	40.0257.010 CACHÉ-CC-SLC-STD-PCA2.0gpm[G]
	40.0258.010 CACHÉ-CC-SLC-STD-PCA1.0gpm[G]
	40.0260.010 CACHÉ-CC-SLC-STD-PCA1.25gpm[G]
	40.0261.010 CACHÉ-CC-SLC-STD-PCA1.75gpm[G]
	40.0402.000 CASCADE-SLC-AC-IT Z
	40.0402.efg CASCADE-SLC-AC Z
	40.0403.000 CASCADE-SLC-AC-IT A
	40.0403.efg CASCADE-SLC-AC A
	40.0451.000 STD-CC-SLC-AC-IT-PCA 5,0 L[G]
	40.0453.000 STD-CC-SLC-AC-IT-PCA 2.2gpm[G]
	40.0455.000 STD-CC-SLC-AC-IT-PCA 7,0 L[G]
	40.0456.000 STD-CC-SLC-AC-IT-PCA 1.5gpm[G]
	40.0457.000 STD-CC-SLC-AC-IT-PCA 2.0gpm[G]
	40.0461.000 STD-CC-SLC-AC-IT-PCA 1.75gpm[G]
	40.1001.000 STD-CC-IT X 2,2 gpm[G]
	40.1002.000 STD-CC-IT Z[G]
	40.1003.000 STD-CC-IT A[G]
	40.1004.000 STD-CC-IT S[G]
	40.1005.000 STD-CC-IT B[G]
	40.1006.000 STD-CC-IT C[G]
	40.1007.000 STD-CC-IT D[G]
	40.1051.000 STD-CC-IT-PCA 5,0 L[G]
	40.1052.000 STD-CC-IT-PCA 6,0 L[G]
	40.1053.000 STD-CC-IT-PCA 2,2 gpm[G]
	40.1054.000 STD-CC-IT-PCA 8,0 L[G]
	40.1055.000 STD-CC-IT-PCA 7,0 L[G]
	40.1056.000 STD-CC-IT-PCA 1,5 gpm[G]
	40.1057.000 STD-CC-IT-PCA 2.0 gpm[G]
	40.1058.000 STD-CC-IT-PCA 1.0 gpm[G]
	40.1060.000 STD-CC-IT-PCA 1.25 gpm[G]
	40.1061.000 STD-CC-IT-PCA 1.75 gpm[G]
	40.1201.010 CACHÉ-CC-STD X 2,2 gpm[G]
	40.1202.010 CACHÉ-CC-STD Z[G]
	40.1203.010 CACHÉ-CC-STD A[G]
	40.1204.010 CACHÉ-CC-STD S[G]
	40.1205.010 CACHÉ-CC-STD B[G]
	40.1206.010 CACHÉ-CC-STD C[G]
	40.1207.010 CACHÉ-CC-STD D[G]
	40.1251.010 CACHÉ-CC-STD-PCA 5,0 L[G]
	40.1252.010 CACHÉ-CC-STD-PCA 6,0 L[G]
	40.1253.010 CACHÉ-CC-STD-PCA 2,2 gpm[G]
	40.1254.010 CACHÉ-CC-STD-PCA 8,0 L[G]
	40.1255.010 CACHÉ-CC-STD-PCA 7,0 L[G]
	40.1256.010 CACHÉ-CC-STD-PCA 1,5 gpm[G]
	40.1257.010 CACHÉ-CC-STD-PCA 2.0gpm[G]
	40.1258.010 CACHÉ-CC-STD-PCA 1.0 gpm[G]
	40.1260.010 CACHÉ-CC-STD-PCA 1.25 gpm[G]
	40.1261.010 CACHÉ-CC-STD-PCA 1.75 gpm[G]
	40.1402.000 CASCADE-AC-IT Z
	40.1402.efg CASCADE-AC Z
	40.1403.000 CASCADE-AC-IT A
	40.1403.efg CASCADE-AC A
	40.1451.000 STD-CC-AC-PCA-IT 5,0 L[G]
	40.1453.000 STD-CC-AC-PCA-IT 2.2gpm[G]
	40.1455.000 STD-CC-AC-PCA-IT 7,0[G]
	40.1456.000 STD-CC-AC-PCA-IT 1.5 gpm[G]
	40.1457.000 STD-CC-AC-PCA-IT 2.0 gpm[G]
	40.1461.000 STD-CC-AC-PCA-IT 1.75 gpm[G]
	40.2001.000 STD-PL-IT X 2,2 gpm[G]
	40.2002.000 STD-PL-IT Z[G]
	40.2003.000 STD-PL-IT A[G]
	40.2004.000 STD-PL-IT S[G]
	40.2005.000 STD-PL-IT B[G]
	40.2006.000 STD-PL-IT C[G]
	40.2007.000 STD-PL-IT D[G]
	40.2010.000 PL-HC-STD-IT-T[G]
	40.2051.000 STD-PL-IT-PCA 5,0 L[G]
	40.2052.000 STD-PL-IT-PCA 6,0 L[G]
	40.2053.000 STD-PL-IT-PCA 2,2 gpm[G]
	40.2054.000 STD-PL-IT-PCA 8,0 L[G]
	40.2055.000 STD-PL-IT-PCA 7,0 L[G]
	40.2056.000 STD-PL-PCA 1,5 gpm[G]
	40.2057.000 STD-PL-IT-PCA 2.0 gpm[G]
	40.2058.000 STD-PL-IT-PCA 1.0 gpm[G]
	40.2060.000 STD-PL-IT-PCA 1.25 gpm[G]
	40.2061.000 STD-PL-IT-PCA 1.75 gpm[G]
	40.2100.000 STD-PL-HC IT LAM MAX[G]
	40.2101.000 STD-PL-HC IT LAM X 2,2 gpm[G]
	40.2102.000 STD-PL-HC IT LAM Z[G]
	40.2103.000 STD-HC IT LAM A[G]
	40.2104.000 STD-PL-HC IT LAM S[G]
	40.2105.000 STD-PL-HC IT LAM B[G]
	40.2106.000 STD-PL-HC IT LAM C[G]
	40.2107.000 STD-PL-HC IT LAM D[G]
	40.2110.000 STD-PL-HC-IT LAM[G]
	40.2151.000 STD-PL-IT-PCA LAMINAR 5,0 L[G]
	40.2152.000 STD-PL-IT-PCA LAMINAR 6,0 L[G]
	40.2153.000 STD-PL-IT-PCA LAMINAR 2,2 gpm[G]
	40.2154.000 STD-PL-IT-PCA LAMINAR 8,0 L[G]
	40.2155.000 STD-PL-IT-PCA LAMINAR 7,0 L[G]
	40.2156.000 STD-PL-IT-PCA 1,5 gpm[G]
	40.2157.000 STD-PL-IT-PCA LAMINAR 2.0 gpm[G]
	40.2158.000 STD-PL-IT-PCA LAMINAR 1.0 gpm[G]
	40.2160.000 STD-PL-IT-PCA LAMINAR 1.25 gpm[G]
	40.2161.000 STD-PL-IT-PCA LAMINAR 1.75 gpm[G]
	40.2194.000 STD-PL-HC IT-C-LAM MAX[G]
	40.2201.010 CACHÉ-PL HC-STD-m M24 X 1-X[G]
	40.2202.010 CACHÉ-PL HC-STD Z[G]
	40.2203.010 CACHÉ-PL HC-STD A[G]
	40.2204.010 CACHÉ-PL HC-STD S[G]
	40.2205.010 CACHÉ-PL HC-STD B[G]
	40.2206.010 CACHÉ-PL HC-STD C[G]
	40.2207.010 CACHÉ-PL HC-STD D[G]
	40.2210.010 CACHÉ-PL HC-STD T 1,5 gpm[G]
	40.2251.010 CACHÉ-HC-STD-PCA 5,0 L[G]
	40.2252.010 CACHE-HC-STD-PCA 6,0L[G]
	40.2253.010 CACHÉ-HC-STD-PCA 2,2 gpm[G]
	40.2254.010 CACHÉ-HC-STD-PCA 8,0 L[G]
	40.2255.010 CACHÉ-HC-STD-PCA 7,0 L[G]
	40.2256.010 CACHÉ-HC-STD-PCA 1,5 gpm[G]
	40.2257.010 CACHÉ-HC-STD-PCA 2.0 gpm[G]
	40.2258.010 CACHÉ-HC-STD-PCA 1.0 gpm[G]
	40.2260.010 CACHÉ-HC-STD-PCA 1.25 gpm[G]
	40.2261.010 CACHÉ-HC-STD-PCA 1.75 gpm[G]
	40.2300.010 CACHÉ-HC-STD-LAM-MAX[G]
	40.2301.010 CACHÉ-HC-STD-LAM X[G]
	40.2302.010 CACHÉ-HC-STD-LAM Z[G]
	40.2303.010 CACHÉ-HC-STD-LAM A[G]
	40.2304.010 CACHÉ-HC-STD-LAM S[G]
	40.2305.010 CACHÉ-HC-STD-LAM B[G]
	40.2306.010 CACHÉ-HC-STD-LAM C[G]
	40.2307.010 CACHÉ-HC-STD-LAM D[G]
	40.2310.010 CACHÉ-HC-STD-LAM T 1,5 gpm[G]
	40.2351.010 CACHÉ-HC-STD-PCA-LAM 5,0 L[G]
	40.2352.010 CACHÉ-HC-STD-PCA-LAM 6.0 L[G]
	40.2353.010 CACHÉ-HC-STD-PCA-LAM 2.2 gpm[G]
	40.2354.010 CACHÉ-HC-STD-PCA-LAM 8,0 L[G]
	40.2355.010 CACHÉ-HC-STD-PCA-LAM 7.0 L[G]
	40.2356.010 CACHÉ-HC-STD-PCA-LAM 1.5 gpm[G]
	40.2357.010 CACHÉ-HC-STD-PCA-LAM 2.0 gpm[G]
	40.2358.010 CACHÉ-HC-STD-PCA-LAM 1.0 gpm[G]
	40.2360.010 CACHÉ-HC-STD-PCA-LAM 1.25 gpm[G]
	40.2361.010 CACHÉ-HC-STD-PCA-LAM 1.75gpm[G]
	40.2402.000 PERLATOR HC AC Z
	40.2402.efg PERLATOR HC AC Z
	40.2403.000 PERLATOR HC AC A
	40.2403.efg PERLATOR HC AC A
	40.2451.000 PL-HA-AC-PCA-IT 5,0L[G]
	40.2453.000 PL-HC-AC-PCA-IT 2.2 gpm[G]
	40.2455.000 PL-HC-AC-PCA-IT 7,0L[G]
	40.2456.000 PL-HC-AC-PCA-IT 1.5gpm[G]
	40.2457.000 PL-HC-AC-PCA-IT 2.0gpm[G]
	40.2461.000 PL-HC-AC-PCA-IT 1.75gpm[G]
	40.3030.000 STD-PL-DIF-IT V[G]
	40.3031.000 STD-PL-DIF-IT 1,0 gpm[G]
	40.3032.000 STD-PL-DIF-IT 1,5 gpm[G]
	40.3033.000 STD-PL-DIF-IT 2,0 gpm[G]
	40.3034.000 STD-PL-DIF-IT 2,2 gpm[G]
	40.3035.000 STD-PL-DIF-IT 3,0 gpm[G]
	40.3036.000 STD-PL-DIF-IT 3,5 gpm[G]
	40.3037.000 STD-PL-DIF-IT 4,0 gpm[G]
	40.3038.000 STD-PL-DIF-IT 4,5 gpm[G]
	40.3039.000 STD-PL-DIF-IT 1.75gpm[G]
	40.3039.efg PERLATOR HC 1.75gpm[G]
	40.3057.efg PL-HC-TT-IT-PCA 2.0gpm[5] [G]
	40.3230.010 CACHÉ-PL-DIF-STD V[G]
	40.3231.010 CACHÉ-PL-DIF-STD 1,0 gpm[G]
	40.3232.010 CACHÉ-PL-DIF-STD 1,5 gpm[G]
	40.3233.010 CACHÉ-PL-DIF-STD 2,0 gpm[G]
	40.3235.010 CACHÉ-PL-DIF-STD 3,0 gpm[G]
	40.3236.010 CACHÉ-PL-DIF-STD 3,5 gpm[G]
	40.3237.010 CACHÉ-PL-DIF-STD 4,0 gpm[G]
	40.3238.010 CACHÉ-PL-DIF-STD 4,5 gpm[G]
	40.3430.000 PERLATOR-HC-IT-AC-HD V
	40.4001.000 STD-PL-LL-IT X 2,2 gpm[G]
	40.4002.000 STD-PL-LL-IT Z[G]
	40.4003.000 STD-PL-LL-IT A[G]
	40.4004.000 STD-PL-LL-IT S[G]
	40.4005.000 STD-PL-LL-IT B[G]
	40.4006.000 STD-PL-LL-IT C[G]
	40.4007.000 STD-PL-LL-IT D[G]
	40.4051.000 STD-PL-LL-IT-PCA 5,0 L[G]
	40.4052.000 STD-PL-LL-IT-PCA 6,0 L[G]
	40.4053.000 STD-PL-LL-IT-PCA 2,2 gpm[G]
	40.4054.000 STD-PL-LL-IT-PCA 8,0 L[G]
	40.4055.000 STD-PL-IT-PCA 7,0 L[G]
	40.4056.000 STD-PL-LL-IT-PCA 1,5 gpm[G]
	40.4057.000 STD-PL-LL-IT-PCA 2.0 gpm[G]
	40.4058.000 STD-PL-LL-IT-PCA 1.0 gpm[G]
	40.4060.000 STD-PL-LL-IT-PCA 1.25 gpm[G]
	40.4061.000 STD-PL-LL-IT-PCA 1.75 gpm[G]
	40.4601.000 STD-PL-DL-IT X 2,2 gpm[G]
	40.4601.efg PERLATOR DL X 2,2gpm[G]
	40.4602.000 STD-PL-DL-IT Z[G]
	40.4602.efg PERLATOR DL Z[G]
	40.4603.000 STD-PL-DL-IT A[G]
	40.4603.efg PERLATOR DL A[G]
	40.4604.000 STD-PL-DL-IT S[G]
	40.4604.efg PERLATOR DL S[G]
	40.4605.000 STD-PL-DL-IT B[G]
	40.4605.efg PERLATOR DL B[G]
	40.4606.000 STD-PL-DL-IT C[G]
	40.4606.efg PERLATOR DL C[G]
	40.4607.000 STD-PL-DL-IT D[G]
	40.4607.efg PERLATOR DL D[G]
	40.4630.008 Bubble Stream-IT-V[G]
	40.4632.008 Bubble Stream-IT 1,5 gpm[G]
	40.4634.008 Bubble Stream-IT 2.2 gpm[G]
	40.4651.000 STD-PL-DL-IT-PCA 5,0 L[G]
	40.4652.000 STD-PL-DL-IT-PCA 6,0 L[G]
	40.4653.000 STD-PL-DL-IT-PCA 2,2 gpm[G]
	40.4654.000 STD-PL-DL-IT-PCA 8,0 L[G]
	40.4655.000 STD-PL-DL-IT-PCA 7.0 L[G]
	40.4656.000 STD-PL-DL-IT-PCA 1.5 gpm[G]
	40.4657.000 STD-PL-DL-IT-PCA 2.0 gpm[G]
	40.4658.000 STD-PL-DL-IT-PCA 1.0 gpm[G]
	40.4660.000 STD-PL-DL-IT-PCA 1.25 gpm[G]
	40.4661.000 STD-PL-DL-IT-PCA 1.75 gpm[G]
	40.4696.008 Bubble Stream-IT 1,5 gpm[G]
	40.4697.008 Bubble STream-IT 2.2 gpm[G]
	40.4699.008 Bubble Stream-IT V[G]
	40.5053.008 BUBBLE STREAM AC STD IT PCA 2.2gpm[G]
	40.5056.008 BUBBLE STREAM AC STD IT PCA 1.5gpm[G]
	40.6001.000 STD-SSR-IT X 2,2 gpm[G]
	40.6002.000 STD-SSR-IT Z[G]
	40.6003.000 STD-SSR-IT A[G]
	40.6004.000 STD-SSR-IT S[G]
	40.6005.000 STD-SSR-IT B[G]
	40.6006.000 STD-PL-HC SSR-IT C[G]
	40.6007.000 STD-PL-HC SSR-IT D[G]
	40.6051.000 STD-PL-HC-SSR-IT-PCA 5,0 L[G]
	40.6051.efg PL-HC-SSR-PCA5,0L[G]
	40.6052.000 STD-PL-HC-SSR-IT-PCA 6,0 L[G]
	40.6052.efg PL-HC-SSR-PCA6,0L[G]
	40.6053.000 STD-PL-HC-SSR-IT-PCA 2,2 gpm[G]
	40.6053.efg PL-HC-SSR-PCA2.2gpm[G]
	40.6054.000 STD-PL-HC-SSR-IT-PCA 8,0 L[G]
	40.6054.efg PL-HC-SSR-PCA8,0L[G]
	40.6055.000 STD-PL-HC-SSR-IT-PCA 7.0 L[G]
	40.6055.efg PL-HC-SSR-PCA7,0L[G]
	40.6056.000 STD-PL-HC-SSR-IT-PCA 1.5 gpm[G]
	40.6056.efg PL-HC-SSR-PCA1.5gpm[G]
	40.6057.000 STD-PL-HC-SSR-IT-PCA 2.0 gpm[G]
	40.6057.efg PL-HC-SSR-PCA2.0 pm[G]
	40.6061.000 STD-PL-HC-SSR-IT-PCA 1.75 gpm[G]
	40.6061.efg PL-HC-SSR-PCA1.785gpm[G]
	40.6201.010 CACHÉ-HC-SSR-STD X 2,2gpm[G]
	40.6202.010 CACHÉ-HC-SSR-STD Z[G]
	40.6203.010 CACHÉ-HC-SSR-STD A[G]
	40.6204.010 CACHÉ-HC-SSR-STD S[G]
	40.6205.010 CACHÉ-HC-SSR-STD B[G]
	40.6206.010 CACHÉ-HC-SSR-STD C[G]
	40.6207.010 CACHÉ-HC-SSR-STD D[G]
	40.6251.000 CACHÉ-HC-SSR-STD-PCA5,0L[G]
	40.6251.010 CACHE-HC-SSR-STD-PCA 5.0L[G]
	40.6252.000 CACHÉ-HC-SSR-STD-PCA6,0L[G]
	40.6252.010 CACHE-HC-SSR-STD-PCA 6.0L[G]
	40.6253.000 CACHÉ-HC-SSR-STD-PCA2.2gpm[G]
	40.6253.010 CACHE-HC-SSR-STD-PCA 2.2gpm[G]
	40.6254.000 CACHÉ-HC-SSR-STD-PCA8,0L[G]
	40.6254.010 CACHE-HC-SSR-STD-PCA 8.0L[G]
	40.6255.000 CACHÉ-HC-SSR-STD-PCA7,0L[G]
	40.6255.010 CACHE-HC-SSR-STD-PCA 7.0L[G]
	40.6256.000 CACHÉ-HC-SSR-STD-PCA1.5gpm[G]
	40.6256.010 CACHE-HC-SSR-STD-PCA 1.5gpm[G]
	40.6257.000 CACHÉ-HC-SSR-STD-PCA2.0 pm[G]
	40.6257.010 CACHE-HC-SSR-STD-PCA 2.0gpm[G]
	40.6261.000 CACHÉ-HC-SSR-STD-PCA1.75gpm[G]
	40.6261.010 CACHE-HC-SSR-STD-PCA 1.75gpm[G]
	40.7258.000 PCA-Spray-SLC-STD-IT 1.0gpm[G]
	40.7259.000 PCA-Spray-SLC-STD-IT 0.5gpm[G]
	40.7268.000 PCA-Spray-SLC-STD-IT 0.35gpm[G]
	40.7358.010 CACHÉ-PCA-SPRAY-STD 1.0gpm[G]
	40.7359.010 CACHÉ-PCA-SPRAY-STD 0.5gpm[G]
	40.7368.010 CACHÉ-PCA-SPRAY-STD 0.35gpm[G]
	40.7559.000 PCA-Spray-AMP-STD-IT-0.35 gpm[G]
	40.7568.000 PCA-Spray-AMP-STD-IT-0.5 gpm[G]
	40.8030.010 SLIM AIR-HC-SSR-STD-m M24x1 V[G]
	40.8030.150 SLIM AIR-HC-SSR-STD-15/16-27 V[G]
	40.8051.010 SLIM AIR-HC-SSR-STD-m M24x1 PCA 5,0L/min[G]
	40.8051.150 SLIM AIR-HC-SSR-STD-15/16-27 PCA 5.0L/min[G]
	40.8053.010 SLIM AIR-HC-SSR-STD-m M24x1 PCA 2.2gpm[G]
	40.8053.150 SLIM AIR-HC-SSR-STD-15/16-27 PCA 2.2gpm[G]
	40.8054.010 SLIM AIR-HC-SSR-STD-m M24x1 PCA 8.0L/min[G]
	40.8054.150 SLIM AIR-HC-SSR-STD-15/16-27 PCA 8.0L/min[G]
	40.8055.010 SLIM AIR-HC-SSR-STD-m M24x1 PCA 7.0L/min[G]
	40.8055.150 SLIM AIR-HC-SSR-STD-15/16-27 PCA 7.0L/min[G]
	40.8056.010 SLIM AIR-HC-SSR-STD-m M24x1 PCA 1.5gpm[G]
	40.8056.150 SLIM AIR-HC-SSR-STD-15/16-27 PCA 1.5gpm[G]
	40.8057.010 SLIM AIR-HC-SSR-STD-m M24x1 PCA 2.0gpm[G]
	40.8130.010 SLIM AIR-CC-SLC-SSR-STD-m M24x1 V[G]
	40.8130.150 SLIM AIR-CC-SLC-SSR-STD-15/16-27 V[G]
	40.8151.010 SLIM AIR-CC-SLC-SSR-STD-M24x1 PCA 5.0L/min[G]
	40.8151.150 SLIM AIR-CC-SLC-SSR-STD-15/16-27 PCA 5.0L/min[G]
	40.8153.010 SLIM AIR-CC-SLC-SSR-STD-M24x1 PCA 2.2gpm[G]
	40.8153.150 SLIM AIR-CC-SLC-SSR-STD-15/16-27 PCA 2.2gpm[G]
	40.8154.010 SLIM AIR-CC-SLC-SSR-STD-M24x1 PCA 8.0L/min[G]
	40.8154.150 SLIM AIR-CC-SLC-SSR-STD-15/16-27 PCA 8.0L/min[G]
	40.8155.010 SLIM AIR-CC-SLC-SSR-STD-M24x1 PCA 7.0L/min[G]
	40.8155.150 SLIM AIR-CC-SLC-SSR-STD-15/16-27 PCA 7,0L/min[G]
	40.8156.010 SLIM AIR-CC-SLC-SSR-STD-M24x1 PCA 1.5gpm[G]
	40.8156.150 SLIM AIR-CC-SLC-SSR-STD-15/16-27 PCA 1.5gpm[G]
	40.8157.010 SLIM AIR-CC-SLC-SSR-STD-M24x1 PCA 2.0gpm[G]
	40.8253.010 SLIM-CC-SLC-SSR-STD-M24x1-lam PCA 2.2gpm[G]
	40.8256.010 SLIM-CC-SLC-SSR-STD-M24x1-lam PCA 1.5gpm[G]
	40.8330.010 SLIM AIR-HC-STD-m M24x1 V[G]
	40.8330.150 SLIM AIR-HC-STD-15/16-27 V[G]
	40.8351.010 SLIM AIR-HC-STD-m M24x1 PCA 5.0L/min[G]
	40.8351.150 SLIM AIR-HC-STD-15/16-27 PCA 5.0L/min[G]
	40.8353.010 SLIM AIR-HC-STD-m M24x1 PCA 2.2gpm[G]
	40.8353.150 SLIM AIR-HC-STD-15/16-27 PCA 2.2gpm[G]
	40.8354.010 SLIM AIR-HC-STD-m M24x1 PCA 8.0L/min[G]
	40.8354.150 SLIM AIR-HC-STD-15/16-27 PCA 8.0L/min[G]
	40.8355.010 SLIM AIR-HC-STD-m M24x1 PCA 7.0L/min[G]
	40.8355.150 SLIM AIR-HC-STD-15/16-27 PCA 7.0L/min[G]
	40.8356.010 SLIM AIR-HC-STD-m M24x1 PCA 1.5gpm[G]
	40.8356.150 SLIM AIR-HC-STD-15/16-27 PCA 1.5gpm[G]
	40.8430.010 SLIM AIR-CC-SLC-STD-m M24x1 V[G]
	40.8430.150 SLIM AIR-CC-SLC-STD-15/16-27 V[G]
	40.8451.010 SLIM AIR-CC-SLC-STD-m M24x1 PCA 5.0L/min[G]
	40.8451.150 SLIM AIR-CC-SLC-STD-15/16-27 PCA 5.0L/min[G]
	40.8453.010 SLIM AIR-CC-SLC-STD-m M24x1 PCA 2.2gpm[G]
	40.8453.150 SLIM AIR-CC-SLC-STD-15/16-27 PCA 2.2gpm[G]
	40.8454.010 SLIM AIR-CC-SLC-STD-m M24x1 PCA 8.0L/min[G]
	40.8454.150 SLIM AIR-CC-SLC-STD-15/16-27 PCA 8.0L/min[G]
	40.8455.010 SLIM AIR-CC-SLC-STD-m M24x1 PCA 7.0L/min[G]
	40.8455.150 SLIM AIR-CC-SLC-STD-15/16-27 PCA 7.0L/min[G]
	40.8456.010 SLIM AIR-CC-SLC-STD-m M24x1 PCA 1.5gpm[G]
	40.8456.150 SLIM AIR-CC-SLC-STD-15/16-27 PCA 1.5gpm[G]
	40.8558.010 SLIM-PCA-SPRAY-STD-m M24x1 1.0gpm[G]
	40.8558.150 SLIM-PCA-SPRAY-SLC-STD-15/16-27 1.0gpm[G]
	40.8559.010 SLIM-PCA-SPRAY-STD-m M24x1 0.5gpm[G]
	40.8559.150 SLIM-PCA-SPRAY-SLC-STD-15/16-27 0.5gpm[G]
	40.8568.010 SLIM-PCA-SPRAY-STD-m M24x1 0.35gpm[G]
	40.8568.150 SLIM-PCA-SPRAY-SLC-STD-15/16-27 0.35gpm[G]
	40.abcd.efg[2] [G]
	40.abcd.efg Aerators
	42.2201.010 CACHÉ-HC-JR X[3] [G]
	42.2202.010 CACHÉ-HC-JR Z[3] [G]
	42.2203.010 CACHÉ-HC-JR A[3] [G]
	42.2205.010 CACHÉ-HC-JR B[3] [G]
	42.2251.010 CACHÉ-HC-JR-PCA 5,0L[3] [G]
	42.2253.010 CACHÉ-HC-JR-PCA 2.2 gpm[3] [G]
	42.2254.010 CACHÉ-HC-JR-PCA 8,0L[3] [G]
	42.2255.010 CACHÉ-HC-JR-PCA 7,0L[3] [G]
	42.2256.010 CACHÉ-HC-JR-PCA 1.5gpm[3] [G]
	42.2257.010 CACHÉ-HC-JR-PCA 2.0gpm[3] [G]
	42.2258.010 CACHÉ-HC-JR-PCA 1.0gpm[3] [G]
	42.2260.010 CACHÉ-HC-JR-PCA 1.25gpm[3] [G]
	42.2261.010 CACHÉ-HC-JR-PCA 1.75gpm[3] [G]
	42.2301.010 CACHÉ-HC-JR lam X[3] [G]
	42.2302.010 CACHÉ-HC-JR lam Z[3] [G]
	42.2303.010 CACHÉ-HC-JR lam A[3] [G]
	42.2305.010 CACHÉ-HC-JR lam B[3] [G]
	42.2351.010 CACHÉ-HC-JR-PCA lam 5,0L[3] [G]
	42.2353.010 CACHÉ-HC-JR-PCA lam 2.2gpm[3] [G]
	42.2354.010 CACHÉ-HC-JR-PCA lam 8,0L[3] [G]
	42.2355.010 CACHÉ-HC-JR-PCA lam 7,0L[3] [G]
	42.2356.010 CACHÉ-HC-JR-PCA lam 1.5gpm[3] [G]
	42.2357.010 CACHÉ-HC-JR-PCA lam 2.0gpm[3] [G]
	42.2358.010 CACHÉ-HC-JR-PCA lam 1.0gpm[3] [G]
	42.2360.010 CACHÉ-HC-JR-PCA lam 1.25gpm[3] [G]
	42.2361.010 CACHÉ-HC-JR-PCA lam 1.75gpm[3] [G]
	42.3030.000 PL-HC-JR-IT V[3] [G]
	42.3031.000 PL-HC-JR-IT1.0gpm[3] [G]
	42.3032.000 PL-HC-JR-IT 1.5gpm[3] [G]
	42.3033.000 PL-HC-JR-IT 2.0gpm[3] [G]
	42.3034.000 PL-HC-JR-IT 2.2gpm[3] [G]
	42.3037.000 PL-HC-JR-IT 4.0gpm[3] [G]
	42.3038.000 PL-HC-JR-IT 4.5gpm[3] [G]
	42.3039.000 PL-HC-JR-IT 1.75gpm[3] [G]
	42.3040.000 PL-HC-JR-IT TS 2.2gpm[3] [G]
	42.3053.000 PL-HC-JR-IT-PCA 2.2gpm[3] [G]
	42.3056.000 PL-HC-JR-IT-PCA 1.5gpm[3] [G]
	42.3057.000 PL-HC-JR-IT-PCA 2.0gpm[3] [G]
	42.3058.000 PL-HC-JR-IT-PCA 1.0gpm[3] [G]
	42.3060.000 PL-HC-JR-IT-PCA 1.25gpm[3] [G]
	42.3061.000 PL-HC-JR-IT-PCA 1.75gpm[3] [G]
	42.3130.000 PL-HC-JR-IT-lam V[3] [G]
	42.3131.000 PL-HC-JR-IT-lam 1.0gpm[3] [G]
	42.3132.000 PL-HC-JR-IT-lam 1.5gpm[3] [G]
	42.3133.000 PL-HC-JR-IT-lam 2.0gpm[3] [G]
	42.3134.000 PL-HC-JR-IT-lam 2.2gpm[3] [G]
	42.3137.000 PL-HC-JR-IT-lam 4.0gpm[3] [G]
	42.3138.000 PL-HC-JR-IT-lam 4.5gpm[3] [G]
	42.3139.000 PL-HC-JR-IT-lam 1.75gpm[3] [G]
	42.3140.000 PL-HC-JR-IT-lam TS 2.2gpm[3] [G]
	42.3153.000 PL-HC-JR-IT-PCA-lam 2.2gpm[3] [G]
	42.3156.000 PL-HC-JR-IT-PCA-lam 1.5gpm[3] [G]
	42.3157.000 PL-HC-JR-IT-PCA-lam 2.0 gpm[3] [G]
	42.3158.000 PL-HC-JR-IT-PCA-lam 1.0gpm[3] [G]
	42.3160.000 PL-HC-JR-IT-PCA-lam 1.25gpm[3] [G]
	42.3161.000 PL-HC-JR-IT-PCA-lam 1.75gpm[3] [G]
	42.3230.010 CACHÉ-HC-JR V[3] [G]
	42.3230.160 CACHÉ-HC-XT-JR V[3] [G]
	42.3231.010 CACHÉ-HC-JR 1.0gpm max.[3] [G]
	42.3231.160 CACHÉ-HC-XT-JR 1.0gpm[3] [G]
	42.3232.010 CACHÉ-HC-JR 1.5gpm[3] [G]
	42.3232.160 CACHÉ-HC-XT-JR 1.5gpm[3] [G]
	42.3233.010 CACHÉ-HC-JR 2.0gpm[3] [G]
	42.3233.160 CACHÉ-HC-XT-JR 2.0gpm[3] [G]
	42.3234.010 CACHÉ-HC-JR 2.2gpm[3] [G]
	42.3234.160 CACHÉ-HC-XT-JR 2.2gpm[3] [G]
	42.3239.010 CACHÉ-HC-JR 1.75gpm[3] [G]
	42.3239.160 CACHÉ-HC-XT-JR 1.75gpm[3] [G]
	42.3253.120 CACHÉ-HC-AX-XT-JR-PCA 2.2gpm[3] [G]
	42.3253.130 CACHÉ-HC-AX-XT-JR-PCA 2.2gpm[3] [G]
	42.3256.120 CACHÉ-HC-AX-XT-JR-PCA 1.5gpm[3] [G]
	42.3256.130 CACHÉ-HC-AX-XT-JR-PCA 1.5gpm[3] [G]
	42.3257.120 CACHÉ-HC-AX-XT-JR-PCA 2.0gpm[3] [G]
	42.3258.120 CACHÉ-HC-AX-XT-JR-PCA 1.0gpm[3] [G]
	42.3260.120 CACHÉ-HC-AX-XT-JR-PCA 1.25gpm[3] [G]
	42.3261.120 CACHÉ-HC-AX-XT-JR-PCA 1.75gpm[3] [G]
	42.3330.010 CACHÉ-HC-JR lam V[3] [G]
	42.3331.010 CACHÉ-HC-JR lam 1.0gpm[3] [G]
	42.3332.010 CACHÉ-HC-JR lam 1.5gpm[3] [G]
	42.3333.010 CACHÉ-HC-JR lam 2.0gpm[3] [G]
	42.3334.010 CACHÉ-HC-JR lam 2.2gpm[3] [G]
	42.3339.010 CACHÉ-HC-JR lam 1.75gpm[3] [G]
	42.6201.010 CACHÉ-HC-SSR-JR X[3] [G]
	42.6202.010 CACHÉ-HC-SSR-JR Z[3] [G]
	42.6203.010 CACHÉ-HC-SSR-JR A[3] [G]
	42.6205.010 CACHÉ-HC-SSR-JR B[3] [G]
	42.6251.010 CACHÉ-HC-SSR-JR-PCA 5,0L[3] [G]
	42.6253.010 CACHÉ-HC-SSR-JR-PCA 2.2gpm[3] [G]
	42.6254.010 CACHÉ-HC-SSR-JR-PCA 8,0L[3] [G]
	42.6255.010 CACHÉ-HC-SSR-JR-PCA 7.0 L[3] [G]
	42.6256.010 CACHÉ-HC-SSR-JR-PCA 1.5gpm[3] [G]
	42.6257.010 CACHÉ-HC-SSR-JR-PCA 2.0gpm[3] [G]
	42.6258.010 CACHÉ-HC-SSR-JR-PCA 1.0gpm[3] [G]
	42.6260.010 CACHÉ-HC-SSR-JR-PCA 1.25gpm[3] [G]
	42.6261.010 CACHÉ-HC-SSR-JR-PCA 1.75gpm[3] [G]
	42.7258.000 PCA-SPRAY-SLC-JR-IT 1.0gpm[3] [G]
	42.7259.000 PCA-SPRAY-SLC-JR-IT 0.5gpm[3] [G]
	42.7268.000 PCA-SPRAY-SLC-JR-IT 0.35gpm[3] [G]
	42.7358.010 CACHÉ-PCA-SPRAY-JR 1,0gpm[3] [G]
	42.7359.010 CACHÉ-PCA-SPRAY-JR 0,5gpm[3] [G]
	42.7368.010 CACHÉ-PCA-SPRAY-JR 0,35gpm[3] [G]
	42.7458.010 CACHÉ-PCA-SPRAY-SLC-JR 1.0gpm[3] [G]
	42.7459.010 CACHÉ-PCA-SPRAY-SLC-JR 0.5gpm[3] [G]
	42.7468.010 CACHÉ-PCA-SPRAY-SLC-JR 0.35gpm[3] [G]
	42.8558.150 SLIM-PCA-SPRAY-SLC-JR-m 13/16-27- 1.0gpm[G]
	42.8559.150 SLIM-PCA-SPRAY-SLC-JR-m 13/16-27-0.5gpm[G]
	42.8568.150 SLIM-PCA-SPRAY-SLC-JR-m 13/16-27-0.35gpm[G]
	43.0030.000 CC-SLC-TJ-IT V[4] [G]
	43.0032.000 CC-SLC-TJ-IT 1.5gpm[4] [G]
	43.0034.000 CC-SLC-TJ-IT 2.2gpm[4] [G]
	43.0051.000 CC-SLC-TJ-IT-PCA 5,0L[4] [G]
	43.0053.000 CC-SLC-TJ-IT-PCA 2.2gpm max.[4] [G]
	43.0054.000 CC-SLC-TJ-IT-PCA 8,0L[4] [G]
	43.0055.000 CC-SLC-TJ-IT-PCA 7,0L[4] [G]
	43.0056.000 CC-SLC-TJ-IT-PCA 1.5gpm max.[4] [G]
	43.0057.000 CC-SLC-TJ-IT-PCA 2.0gpm max.[4] [G]
	43.0061.000 CC-SLC-TJ-IT-PCA 1.75gpm max.[4] [G]
	43.2001.000PL-HC-TJ-IT X[4] [G]
	43.2002.000 PL-HC-TJ-IT Z[4] [G]
	43.2003.000 PL-HC-TJ-IT A[4] [G]
	43.2005.000 PL-HC-TJ-IT B[4] [G]
	43.2051.000 PL-HC-TJ-IT-PCA 5,0L[4] [G]
	43.2053.000 PL-HC-TJ-IT-PCA 2.2gpm[4] [G]
	43.2054.000 PL-HC-TJ-IT-PCA 8,0L[4] [G]
	43.2055.000 PL-HC-TJ-IT-PCA 7.0L[4] [G]
	43.2056.000 PL-HC-TJ-IT-PCA 1.5gpm[4] [G]
	43.2057.000 PL-HC-TJ-IT-PCA 2.0gpm[4] [G]
	43.2058.000 PL-HC-TJ-IT-PCA 1.0gpm[4] [G]
	43.2060.000 PL-HC-TJ-IT-PCA 1.25gpm[4] [G]
	43.2061.000 PL-HC-TJ-IT-PCA 1.75gpm[4] [G]
	43.2101.000 PL-HC-TJ-IT-lam X[4] [G]
	43.2102.000 PL-HC-TJ-IT-lam Z[4] [G]
	43.2103.000 PL-HC-TJ-IT-lam A[4] [G]
	43.2105.000 PL-HC-TJ-IT-lam B[4] [G]
	43.2151.000 PL-HC-TJ-IT-PCA-lam 5,0L[4] [G]
	43.2153.000 PL-HC-TJ-IT-PCA-lam 2.2gpm[4] [G]
	43.2154.000 PL-HC-TJ-IT-PCA-lam 8,0L[4] [G]
	43.2155.000 PL-HC-TJ-IT-PCA-lam 7.0L[4] [G]
	43.2156.000 PL-HC-TJ-IT-PCA-lam 1.5gpm[4] [G]
	43.2157.000 PL-HC-TJ-IT-PCA-lam 2.0gpm[4] [G]
	43.2158.000 PL-HC-TJ-IT-PCA-lam 1.0gpm[4] [G]
	43.2160.000 PL-HC-TJ-IT-PCA-lam 1.25gpm[4] [G]
	43.2161.000 PL-HC-TJ-IT-PCA-lam 1.75gpm[4] [G]
	43.2201.010 CACHÉ-HC-TJ X[4] [G]
	43.2202.010 CACHÉ-HC-TJ Z[4] [G]
	43.2203.010 CACHÉ-HC-TJ A[4] [G]
	43.2205.010CACHÉ-HC-TJ B[4] [G]
	43.2251.010 CACHÉ-HC-TJ-PCA 5,0L[4] [G]
	43.2251.160 Caché-HC-XT-TJ-m M18.5x1 PCA 5.0L[4] [G]
	43.2253.010 CACHÉ-HC-TJ-PCA 2.2gpm[4] [G]
	43.2253.160 Caché-HC-XT-TJ-m M18.5x1 PCA 2.2gpm[4] [G]
	43.2254.010 CACHÉ-HC-TJ-PCA 8,0L[4] [G]
	43.2254.160 Caché-HC-XT-TJ-m M18.5x1 PCA 8.0L[4] [G]
	43.2255.010 Caché-HC-TJ-PCA 7.0L[4] [G]
	43.2255.160 Caché-HC-XT-TJ-m M18.5x1 PCA 7.0L[4] [G]
	43.2256.010 CACHÉ-HC-TJ-PCA 1.5gpm[4] [G]
	43.2256.160 Caché-HC-XT-TJ-m M18.5x1 PCA 1.5gpm[4] [G]
	43.2257.010 CACHÉ-HC-TJ-PCA 2.0gpm[4] [G]
	43.2257.160 Caché-HC-XT-TJ-m M18.5x1 PCA 2.0gpm[4] [G]
	43.2258.010 Caché HC TJ-PCA 1.0 gpm[4] [G]
	43.2260.010 CACHÉ-HC-TJ-PCA 1.25gpm[4] [G]
	43.2261.010 CACHÉ-HC-TJ-PCA 1.75gpm[4] [G]
	43.2261.160 Caché-HC-XT-TJ-m M18.5x1 PCA 1.75gpm[4] [G]
	43.2301.010 CACHÉ-HC-TJ lam X[4] [G]
	43.2302.010 CACHÉ-HC-TJ lam Z[4] [G]
	43.2303.010 CACHÉ-HC-TJ lam A[4] [G]
	43.2305.010 CACHÉ-HC-TJ lam B[4] [G]
	43.2351.010 CACHÉ-HC-TJ-PCA lam 5,0L[4] [G]
	43.2353.010 CACHÉ-HC-TJ-PCA lam 2.2gpm[4] [G]
	43.2354.010 CACHÉ-HC-TJ-PCA lam 8,0L[4] [G]
	43.2355.010 Caché HC-TJ-PCA-lam 7.0L[4] [G]
	43.2356.010 CACHÉ-HC-TJ-PCA lam 1.5gpm[4] [G]
	43.2357.010 CACHÉ-HC-TJ-PCA-lam 2.0gpm[4] [G]
	43.2358.010 CACHÉ-HC-TJ-PCA-lam 1.0gpm[4] [G]
	43.2360.010 CACHÉ-HC-TJ-PCA-lam 1.25gpm[4] [G]
	43.2361.010 CACHÉ-HC-TJ-PCA-lam 1.75gpm[4] [G]
	43.3030.000 PL-HC-TJ-IT V[4] [G]
	43.3031.000 PL-HC-TJ-IT 1.0gpm[4] [G]
	43.3032.000 PL-HC-TJ-IT 1.5gpm max.[4] [G]
	43.3033.000 PL-HC-TJ-IT 2.0gpm[4] [G]
	43.3034.000 PL-HC-TJ-IT 2.2gpm max.[4] [G]
	43.3039.000 PL-HC-TJ-IT 1.75gpm max.[4] [G]
	43.3130.000PL-HC-TJ-IT-lam V[4] [G]
	43.3131.000 PL-HC-TJ-IT-lam 1.0gpm max.[4] [G]
	43.3132.000 PL-HC-TJ-IT-lam 1.5gpm max.[4] [G]
	43.3133.000 PL-HC-TJ-IT-lam 2.0gpm max.[4] [G]
	43.3134.000 PL-HC-TJ-IT-lam 2.2gpm max.[4] [G]
	43.3139.000 PL-HC-TJ-IT-lam 1.75gpm max.[4] [G]
	43.3230.010 CACHÉ-HC-TJ V[4] [G]
	43.3230.160 Caché-HC-XT-TJ-m M18.5x1V[4] [G]
	43.3231.010 CACHÉ-HC-TJ 1.0gpm max.[4] [G]
	43.3232.010 CACHÉ-HC-TJ 1.5gpm max.[4] [G]
	43.3232.160 Caché-HC-XT-TJ-m M18.5x1 1.5 gpm[4] [G]
	43.3233.010 CACHÉ-HC-TJ 2.0gpm max.[4] [G]
	43.3234.010 CACHÉ-HC-TJ 2.2gpm max.[4] [G]
	43.3234.160 Caché-HC-XT-TJ-m M18.5x1 2.2 gpm[4] [G]
	43.3239.010 CACHÉ-HC-TJ 1.75gpm max.[4] [G]
	43.3330.010 CACHÉ-HC-TJ-lam V[4] [G]
	43.3331.010 CACHÉ-HC-TJ-lam 1.0gpm max.[4] [G]
	43.3332.010 CACHÉ-HC-TJ-lam 1.5gpm max.[4] [G]
	43.3333.010 CACHÉ-HC-TJ-lam 2.0gpm max.[4] [G]
	43.3334.010 CACHÉ-HC-TJ-lam 2.2gpm max.[4] [G]
	43.3339.010 CACHÉ-HC-TJ-lam 1.75gpm max.[4] [G]
	43.6001.000 PL-HC-SSR-TJ-ITX[4] [G]
	43.6002.000 PL-HC-SSR-TJ-ITZ[4] [G]
	43.6003.000 PL-HC-SSR-TJ-ITA[4] [G]
	43.6005.000 PL-HC-SSR-TJ-ITB[4] [G]
	43.6051.000 PL-HC-SSR-TJ-IT-PCA 5.0L[4] [G]
	43.6053.000 PL-HC-SSR-TJ-IT-PCA 2.2gpm[4] [G]
	43.6054.000 PL-HC-SSR-TJ-IT-PCA 8.0L[4] [G]
	43.6055.000 PL-HC-SSR-TJ-IT-PCA 7.0L[4] [G]
	43.6056.000 PL-HC-SSR-TJ-IT-PCA 1.5gpm[4] [G]
	43.6057.000 PL-HC-SSR-TJ-IT-PCA 2.0gpm[4] [G]
	43.6058.000 PL-HC-SSR-TJ-IT-PCA 1.0 gpm max.[4] [G]
	43.6060.000 PL-HC-SSR-TJ-IT-PCA 1.25 gpm max.[4] [G]
	43.6061.000 PL-HC-SSR-TJ-IT-PCA 1.75gpm[4] [G]
	43.6201.010 CACHÉ-HC-SSR-TJ X[4] [G]
	43.6202.010 CACHÉ-HC-SSR-TJ Z[4] [G]
	43.6203.010 CACHÉ-HC-SSR-TJ A[4] [G]
	43.6205.010 CACHÉ-HC-SSR-TJ B[4] [G]
	43.6251.010 Caché HC-SSR-TJ-PCA 5.0L[4] [G]
	43.6253.010 Caché HC-SSR-TJ-PCA 2.2gpm[4] [G]
	43.6254.010 Caché HC-SSR-TJ-PCA 8.0L[4] [G]
	43.6255.010 Caché HC-SSR-TJ-PCA 7.0L[4] [G]
	43.6256.010 Caché HC-SSR-TJ-PCA 1.5gpm[4] [G]
	43.6257.010 Caché HC-SSR-TJ-PCA 2.0gpm[4] [G]
	43.6261.010 Caché HC-SSR-TJ-PCA 1.75gpm[4] [G]
	43.7258.000 PCA-Spray-SLC-TJ-IT 1.0gpm[4] [G]
	43.7259.000 PCA-Spray-SLC-TJ-IT 0.5gpm[4] [G]
	43.7268.000 PCA-Spray-SLC-TJ-IT 0.35 gpm[4] [G]
	43.7358.010 Caché-PCA-Spray-TJ 1.0gpm[4] [G]
	43.7359.010 Caché-PCA-Spray-TJ 0.5gpm[4] [G]
	43.7458.010 Caché-PCA-Spray-SLC-TJ 1.0gpm[4] [G]
	43.7459.010 Caché-PCA-Spray-SLC-TJ 0.5gpm[4] [G]
	43.7468.010 Cache-PCA-Spray-SLC-TJ 0.35gpm max[4] [G]
	43.9300.160 Caché-FS-dripless-XT-TJ-m M18.5x1max[4] [G]
	43.9400.010 Caché-FS-LP-TJ-m M18.5x1max[4] [G]
	43.9600.010 Caché-FS-LP-dripless-TJ-m M18.5x1max[4] [G]
	44.3030.efg PL-HC-TT-IT V[5] [G]
	44.3031.efg PL-HC-TT-IT 1.0gpm[5] [G]
	44.3032.efg PL-HC-TT-IT 1.5gpm[5] [G]
	44.3033.efg PL-HC-TT-IT 2.0gpm[5] [G]
	44.3034.efg PL-HC-TT-IT 2.2gpm[5] [G]
	44.3039.efg PL-HC-TT-IT 1.75gpm[5] [G]
	44.3051.efg PL-HC-TT-IT-PCA 5,0l/min[5] [G]
	44.3053.efg PL-HC-TT-IT-PCA 2.2gpm[5] [G]
	44.3054.efg PL-HC-TT-IT-PCA 8,0l/min[5] [G]
	44.3055.efg PL-HC-TT-IT-PCA 7,0l/min[5] [G]
	44.3056.efg PL-HC-TT-IT-PCA 1.5gpm[5] [G]
	44.3058.efg PL-HC-TT-IT-PCA 1.0gpm[5] [G]
	44.3060.efg PL-HC-TT-IT-PCA 1.25gpm[5] [G]
	44.3061.efg PL-HC-TT-IT-PCA 1.75gpm[5] [G]
	44.3130.efg PL-HC-TT-IT-lam V[5] [G]
	44.3131.efg PL-HC-TT-IT-lam 1.0gpm[5] [G]
	44.3132.efg PL-HC-TT-IT-lam 1.5gpm[5] [G]
	44.3133.efg PL-HC-TT-IT-lam 2.0gpm[5] [G]
	44.3134.efg PL-HC-TT-IT-lam 2.2gpm[5] [G]
	44.3139.efg PL-HC-TT-IT-lam 1.75gpm[5] [G]
	44.3151.efg PL-HC-TT-IT-PCA-lam 5,0l/min[5] [G]
	44.3153.efg PL-HC-TT-IT-PCA-lam 2.2gpm[5] [G]
	44.3154.efg PL-HC-TT-IT-PCA-lam 8,0l/min[5] [G]
	44.3155.efg PL-HC-TT-IT-PCA-lam 7,0l/min[5] [G]
	44.3156.efg PL-HC-TT-IT-PCA-lam 1.5gpm[5] [G]
	44.3157.efg PL-HC-TT-IT-PCA-lam 2.0gpm[5] [G]
	44.3158.efg PL-HC-TT-IT-PCA-lam 1.0gpm[5] [G]
	44.3159.efg PL-HC-TT-IT-PCA-lam 0.5gpm[5] [G]
	44.3160.efg PL-HC-TT-IT-PCA-lam 1.25gpm[5] [G]
	44.3161.efg PL-HC-TT-IT-PCA-lam 1.75gpm[5] [G]
	44.3164.efg PL-HC-TT-IT-PCA-lam 3.0gpm[5] [G]
	44.3230.010 CACHÉ-HC-TT-m M16,5x1 V[5] [G]
	44.3230.060 CACHÉ-HC-XT-TT-m M16,5x1 V[5] [G]
	44.3231.010 CACHÉ-HC-TT-m M16,5x1 1.0gpm[5] [G]
	44.3231.060 CACHÉ-HC-XT-TT-m M16,5x1 1.0gpm[5] [G]
	44.3232.010 CACHÉ-HC-TT-m M16,5x1 1.5gpm[5] [G]
	44.3232.060 CACHÉ-HC-XT-TT-m M16,5x1 1.5gpm[5] [G]
	44.3233.010 CACHÉ-HC-TT-m M16,5x1 2.0gpm[5] [G]
	44.3233.060 CACHÉ-HC-XT-TT-m M16,5x1 2.0gpm[5] [G]
	44.3234.010 CACHÉ-HC-TT-m M16,5x1 2.2gpm[5] [G]
	44.3234.060 CACHÉ-HC-XT-TT-m M16,5x1 2.2gpm[5] [G]
	44.3239.010 CACHÉ-HC-TT-m M16,5x1 1.75gpm[5] [G]
	44.3239.060 CACHÉ-HC-XT-TT-m M16,5x1 1.75gpm[5] [G]
	44.3251.010 CACHÉ-HC-TT-m M16,5x1-PCA 5,0l/min[5] [G]
	44.3251.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 5,0l/min[5] [G]
	44.3253.010 CACHÉ-HC-TT-m M16,5x1-PCA 2.2gpm[5] [G]
	44.3253.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 2.2gpm[5] [G]
	44.3254.010 CACHÉ-HC-TT-m M16,5x1-PCA 8,0l/min[5] [G]
	44.3254.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 8,0l/min[5] [G]
	44.3255.010 CACHÉ-HC-TT-m M16,5x1-PCA 7,0l/min[5] [G]
	44.3255.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 7,0l/min[5] [G]
	44.3256.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.5gpm[5] [G]
	44.3256.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.5gpm[5] [G]
	44.3257.010 CACHÉ-HC-TT-m M16,5x1-PCA 2.0gpm[5] [G]
	44.3257.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 2.0gpm[5] [G]
	44.3258.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.0gpm[5] [G]
	44.3258.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.0gpm[5] [G]
	44.3260.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.25gpm[5] [G]
	44.3260.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.25gpm[5] [G]
	44.3261.010 CACHÉ-HC-TT-m M16,5x1-PCA 1.75gpm[5] [G]
	44.3261.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA 1.75gpm[5] [G]
	44.3330.010 CACHÉ-HC-TT-m M16,5x1-lam V[5] [G]
	44.3330.060 CACHÉ-HC-XT-TT-m M16,5x1-lam V[5] [G]
	44.3331.010 CACHÉ-HC-TT-m M16,5x1-lam 1.0gpm[5] [G]
	44.3331.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 1.0gpm[5] [G]
	44.3332.010 CACHÉ-HC-TT-m M16,5x1-lam 1.5gpm[5] [G]
	44.3332.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 1.5gpm[5] [G]
	44.3333.010 CACHÉ-HC-TT-m M16,5x1-lam 2.0gpm[5] [G]
	44.3333.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 2.0gpm[5] [G]
	44.3334.010 CACHÉ-HC-TT-m M16,5x1-lam 2.2gpm[5] [G]
	44.3334.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 2.2gpm[5] [G]
	44.3339.010 CACHÉ-HC-TT-m M16,5x1-lam 1.75gpm[5] [G]
	44.3339.060 CACHÉ-HC-XT-TT-m M16,5x1-lam 1.75gpm[5] [G]
	44.3351.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 5,0l/min[5] [G]
	44.3351.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 5,0l/min[5] [G]
	44.3353.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 2.2gpm[5] [G]
	44.3353.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 2.2gpm[5] [G]
	44.3354.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 8,0l/min[5] [G]
	44.3354.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 8,0l/min[5] [G]
	44.3355.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 7,0l/min[5] [G]
	44.3355.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 7,0l/min[5] [G]
	44.3356.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.5gpm[5] [G]
	44.3356.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.5gpm[5] [G]
	44.3357.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 2.0gpm[5] [G]
	44.3357.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 2.0gpm[5] [G]
	44.3358.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.0gpm[5] [G]
	44.3358.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.0gpm[5] [G]
	44.3359.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 0.5gpm[5] [G]
	44.3360.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.25gpm[5] [G]
	44.3360.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.25gpm[5] [G]
	44.3361.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 1.75gpm[5] [G]
	44.3361.060 CACHÉ-HC-XT-TT-m M16,5x1-PCA-lam 1.75gm[5] [G]
	44.3364.010 CACHÉ-HC-TT-m M16,5x1-PCA-lam 3.0gpm[5] [G]
	44.7158.efg PCA-SPRAY-TT-IT 1.0gpm[5] [G]
	44.7159.efg PCA-SPRAY-TT-IT 0.5gpm[5] [G]
	44.7165.efg PCA-SPRAY-TT-IT 0.38gpm[5] [G]
	44.7168.efg PCA-SPRAY-TT-IT 0.35gpm[5] [G]
	44.7358.010 CACHÉ-PCA-Spray-TT-m M16,5x1 1.0gpm[5] [G]
	44.7359.010 CACHÉ-PCA-Spray-TT-m M16,5x1 0.5gpm[5] [G]
	45.2002.000 PL-HC-CS-STD-m M24x1 Z[G] [22]
	45.2003.000 PL-HC-CS-STD-m M24x1 A[G] [22]
	45.2005.000 PL-HC-CS-STD-m M24x1 B[G] [22]
	45.2006.000 PL-HC-CS-STD-m M24x1 C[G] [22]
	45.2051.000 PL-HC-CS-STD-m M24x1-PCA 5.0L[G] [22]
	45.2053.000 PL-HC-CS-STD-m M24x1-PCA 2.2 gpm[G] [22]
	45.2053.050 PL-HC-CS-STD-m 15/16-27-PCA 2.2 gpm[G] [22]
	45.2053.220 PL-HC-CS-JR-PCA 2.2 gpm[G] [22]
	45.2054.000 PL-HC-CS-STD-m M24x1-PCA 8.0L[G] [22]
	45.2055.000 PL-HC-CS-STD-m M24x1-PCA 7.0L[G] [22]
	45.2056.000 PL-HC-CS-STD-m M24x1-PCA 1.5 gpm[G] [22]
	45.2056.050 PL-HC-CS-STD-m 15/16-27-PCA 1.5 gpm[G] [22]
	45.2056.220 PL-HC-CS-JR-PCA 1.5 gpm[G] [22]
	45.2057.000 PL-HC-CS-STD-m M24x1-PCA 2.0 gpm[G] [22]
	45.2057.050 PL-HC-CS-STD-m 15/16-27-PCA 2.0 gpm[G] [22]
	45.3030.000 PL-HC-CS-STD-m M24x1 V[G] [22]
	45.3030.050 PL-HC-CS-STD-m 15/16-27 V[G] [22]
	45.3030.220 PL-HC-CS-JR V[G] [22]
	A5.4106.0 CC-SLC Insert PCA 6.0 L[G]
	A5.4115.0 CC-SLC Insert PCA 2.2 gpm[G]
	A5.4117.0 CC-SLC Insert PCA 8.0 L[G]
	A5.4120.0 CC-SLC Insert PCA 5.0 L[G]
	A5.4130.0 PCA - Cascade Insert 3,0 L
	A5.4132.0 PCA - Cascade Insert 5,0 L
	A5.4143.0 PCA - Cascade Insert 6,0 L
	A5.4145.0 PCA - Cascade Insert 7,6 L
	A5.4146.0 PCA - Cascade Insert 8,0 L
	A5.4160.0 PCA - Care Insert 3,0 L
	A5.4162.0 PCA - Care Insert 5,0 L
	A5.4163.0 PCA - Care Insert 6,0 L
	A5.4165.0 PCA - Care Insert 7,6 L
	A5.4166.0 PCA - Care Insert 8,0 L
	A5.4214.0 CC-SLC M22x1 PCA 6.0 L[G]
	A5.4215.0 CC-SLC M22x1 PCA 2.2 gpm[G]
	A5.4216.0 CC-SLC M22x1 PCA 8.0 L[G]
	A5.4240.0 PCA - Cascade M22x1 3,0 L
	A5.4242.0 PCA - Cascade M22x1 5,0 L
	A5.4243.0 PCA - Cascade M22x1 6,0 L
	A5.4245.0 PCA - Cascade M22x1 7,6 L
	A5.4246.0 PCA - Cascade M22x1 8,0 L
	A5.4260.0 PCA - Care M22x1 3,0 L
	A5.4262.0 PCA - Care M22x1 5,0 L
	A5.4263.0 PCA - Care M22x1 6,0 L
	A5.4265.0 PCA - Care M22x1 7,6 L
	A5.4266.0 PCA - Care M22x1 8,0 L
	A5.4413.0 CC-SLC M24x1 PCA 8.0 L[G]
	A5.4414.0 CC-SLC M24x1 PCA 6.0 L[G]
	A5.4415.0 CC-SLC M24x1 PCA 2.2 gpm[G]
	A5.4440.0 PCA - Cascade M24x1 3,0 L
	A5.4442.0 PCA - Cascade M24x1 5,0 L
	A5.4443.0 PCA - Cascade M24x1 6,0 L
	A5.4445.0 PCA - Cascade M24x1 7,6 L
	A5.4446.0 PCA - Cascade M24x1 8,0 L
	A5.4460.0 PCA - Care M24x1 3,0 L
	A5.4462.0 PCA - Care M24x1 5,0 L
	A5.4463.0 PCA - Care M24x1 6,0 L
	A5.4465.0 PCA - Care M24x1 7,6 L
	A5.4466.0 PCA - Care M24x1 8,0 L
	A5.4640.0 PCA - Cascade M22x1 VP 3,0 L
	A5.4642.0 PCA - Cascade M22x1 VP 5,0 L
	A5.4643.0 PCA - Cascade M22x1 VP 6,0 L
	A5.4645.0 PCA - Cascade M22x1 VP 7,6 L
	A5.4646.0 PCA - Cascade M22x1 VP 8,0 L
	A5.4660.0 PCA - Care M22x1 VP 3,0 L
	A5.4662.0 PCA - Care M22x1 VP 5,0 L
	A5.4663.0 PCA - Care M22x1 VP 6,0 L
	A5.4665.0 PCA - Care M22x1 VP 7,6 L
	A5.4666.0 PCA - Care M22x1 VP 8,0 L
	A5.4840.0 PCA - Cascade M24x1 VP 3,0 L
	A5.4842.0 PCA - Cascade M24x1 VP 5,0 L
	A5.4843.0 PCA - Cascade M24x1 VP 6,0 L
	A5.4845.0 PCA - Cascade M24x1 VP 7,6 L
	A5.4846.0 PCA - Cascade M24x1 VP 8,0 L
	A5.4860.0 PCA - Care M24x1 VP 3,0 L
	A5.4862.0 PCA - Care M24x1 VP 5,0 L
	A5.4863.0 PCA - Care M24x1 VP 6,0 L
	A5.4865.0 PCA - Care M24x1 VP 7,6 L
	A5.4866.0 PCA - Care M24x1 VP 8,0 L
	A5.9035.1.efgh PCA Spray Jr Insert 1,7 L/min[6] [G]
	A5.9036.1.efgh PCA Spray Jr Insert 3,5 L/min[6] [G]
	A5.9037.efgh PCA Spray Jr 0.35gpm Insert Assembly[6] [G]
	A5.9041.efgh PCS Spray Std. 0.35gpm Insert Assembly[6] [G]
	A5.9042.1.efgh PCA Spray Insert 1,7 L/min[6] [G]
	A5.9043.1.efgh PCA Spray Insert 2,0 L/min[6] [G]
	A5.9044.1.efgh PCA Spray Insert 2,5 L/min[6] [G]
	A5.9045.1.efgh PCA Spray Insert 3,0 L/min[6] [G]
	A5.9046.1.efgh PCA Spray Insert 3,5 L/min[6] [G]
	A5.9047.1.efgh PCA Spray Insert 4,0 L/min[6] [G]
	A5.9049.1.efgh PCA Spray Insert 5,0 L/min[6] [G]
	A5.9142.0.efgh PCA Spray M22x1 VP 1,7 L/min[6] [G]
	A5.9143.0.efgh PCA Spray M22x1 2,0 L/min[6] [G]
	A5.9144.0.efgh PCA Spray M22x1 2,5 L/min[6] [G]
	A5.9145.0.efgh PCA Spray M22x1 3,0 L/min[6] [G]
	A5.9146.0.efgh PCA Spray M22x1 3,5 L/min[6] [G]
	A5.9147.0.efgh PCA Spray M22x1 4,0 L/min[6] [G]
	A5.9149.0.efgh PCA Spray M22x1 5,0 L/min[6] [G]
	A5.9162.0.efgh PCA Spray M22x1 VP 1,7 L/min[6] [G]
	A5.9163.0.efgh PCA Spray M22x1 VP 2,0 L/min[6] [G]
	A5.9164.0.efgh PCA Spray M22x1 VP 2,5 L/min[6] [G]
	A5.9165.0.efgh PCA Spray M22x1 VP 3,0 L/min[6] [G]
	A5.9166.0.efgh PCA Spray M22x1 VP 3,5 L/min[6] [G]
	A5.9167.0.efgh PCA Spray M22x1 VP 4,0 L/min[6] [G]
	A5.9169.0.efgh PCA Spray M22x1 VP 5,0 L/min[6] [G]
	A5.9242.0.efgh PCA Spray M24x1 1,7 L/min[6] [G]
	A5.9243.0.efgh PCA Spray M24x1 2,0 L/min[6] [G]
	A5.9244.0.efgh PCA Spray M24x1 2,5 L/min[6] [G]
	A5.9245.0.efgh PCA Spray M24x1 3,0 L/min[6] [G]
	A5.9246.0.efgh PCA Spray M24x1 3,5 L/min[6] [G]
	A5.9247.0.efgh PCA Spray M24x1 4,0 L/min[6] [G]
	A5.9249.0.efgh PCA Spray M24x1 5,0 L/min[6] [G]
	A5.9262.0.efgh PCA Spray M24x1 VP 1,7 L/min[6] [G]
	A5.9263.0.efgh PCA Spray M24x1 VP 2,0 L/min[6] [G]
	A5.9264.0.efgh PCA Spray M24x1 VP 2,5 L/min[6] [G]
	A5.9265.0.efgh PCA Spray M24x1 VP 3,0 L/min[6] [G]
	A5.9266.0.efgh PCA Spray M24x1 VP 3,5 L/min[6] [G]
	A5.9267.0.efgh PCA Spray M24x1 VP 4,0 L/min[6] [G]
	A5.9269.0.efgh PCA Spray M24x1 VP 5,0 L/min[6] [G]
[1] PL - Perlator RC - Rectangular FS - Flow straightener 40X10, 38X12, 32X8, 28X7, 24.5X9, 24X8, 24X6 - Nominal length and width in millimeters IT - Insert LAM - Laminar flow HC - Honeycomb RS – Rectangular seal C – Diffuser plate and dome screen C B – Diffuser plate and dome screen B A - Diffuser plate and dome screen A V – Flow rate for aerators with diffuser system TUB – Tub filler size RD – Radial washer shape AX – Axial washer shape [2] a - Line/model 0 - Cascade SLC 1 - Cascade or Perlator DL 2 - Perlator honeycomb 3 - Perlator honeycomb (diffuser technology) 4 - Perlator LL 6 - SSR b - Aerated/laminar (incl. CACHÉ) 0 - Aerated 1 - Laminar 2 - Aerated CACHÉ 3 - Laminar CACHÉ 6 - Deluxe cd - Flow rate 00 - Max 01 - X 02 - Z 03 - A 04 - S 05 - B 06 - C 07 - D 10 - T 30 - Diffuser V 31 - Diffuser 1,0 gpm 32 - Diffuser 1,5 gpm 33 - Diffuser 2,0 gpm 34 - Diffuser 2,2 gpm 35 - Diffuser 3,0 gpm 36 - Diffuser 3,5 gpm 37 - Diffuser 4,0 gpm 38 - Diffuser 4,5 gpm 51 - PCA 5,0 L 52 - PCA 6,0 L 53 - PCA 2,2 L 54 - PCA 8,0 L 55 - PCA 7,0 L 56 - PCA 1,5 gpm 57 - PCA 2,0 gpm 58 - PCA 1,0 gpm 60 - PCA 1,25 gpm 61 - PCA 1,75 gpm efg - Brass housing/surface thread Part numbers may also contain an additional numeric suffix to indicate packaging and external markings. [3] 42 - JR size MC aerators a - Line/model 2 - Perlator honeycomb 3 - Perlator honeycomb (diffuser technology) b - Aerated/laminar (incl. CACHÉ) 0 - Aerated 1 - Laminar 2 - Aerated CACHÉ 3 - Laminar CACHÉ cd - Flow rate 01 - X 02 - Z 03 - A 05 - B 30 - Diffuser V 31 - Diffuser 1.0 gpm 32 - Diffuser 1.5 gpm 33 - Diffuser 2.0 gpm 34 - Diffuser 2.2 gpm 39 - Diffuser 1.75 gpm 51 - PCA 5.0 L 53 - PCA 2.2 gpm 54 - PCA 8.0 L 56 - PCA 1.5 gpm 57 - PCA 2.0 gpm 58 - PCA 1.0 gpm 60 - PCA 1.25 gpm 61 - PCA 1.75 gpm efg - Brass housing/surface thread Part numbers may also contain an additional numeric suffix to indicate packaging and external markings. [4] 43 - TJ Size MC Aerators ab – Line 20 - Perlator Honeycomb 21 - Perlator Honeycomb laminar 22 - CACHÉ Perlator Honeycomb 23 - CACHÉ Perlator Honeycomb laminar 30 – Perlator Honeycomb (diffuser technology) 31 - Perlator Honeycomb (diffuser technology) laminar 32 - CACHÉ Perlator Honeycomb (diffuser technology) 33 - CACHÉ Perlator Honeycomb (diffuser technology) laminar 60 – SSR (Aerator with swiveling honeycomb plate) cd - Flow rate 01 - X 02 - Z 03 - A 05 - B 30 - Diffuser V 31 - Diffuser 1.0gpm 32 - Diffuser 1.5gpm 33 - Diffuser 2.0gpm 34 - Diffuser 2.2gpm 39 - Diffuser 1.75gpm 51 - PCA 5.0L 53 - PCA 2.2gpm 54 - PCA 8.0L 55 - PCA 7.0L 56 - PCA 1.5gpm 57 - PCA 2.0gpm 58 - PCA 1.0gpm 60 - PCA 1.25gpm 61 - PCA 1.75gpm efg - brass housing/surface thread Part numbers may also contain an additional numeric suffix to indicate packaging and external markings. [5] efg - Brass housing/surface thread Part numbers may also contain an additional numeric suffix to indicate packaging and external markings. [6] efgh - Packaging (0001 to 9999) consecutively numbered. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%. [22] PL - Perlator HC - Honeycomb CS - Coinslot STD - Standard size JR - Junior size PCA - Pressure compensation aerator
End Point Control Valves[6] [G]
	30.0010.0.efgh DW 10 I Check Valve Cartridge
	30.4001.0.efgh DW 13 KG F Check Valve Cartridge[G]
	30.4003.0.efgh DW 10-14 psi Check Valve Cartridge[G]
	30.4004.0.efgh DW 10 IS Check Valve Cartridge[G]
	30.4009.0.efgh DW 10 P Check Valve Cartridge[G]
	30.4010.0.efgh DW 10 Check Valve Cartridge[G]
	30.4011.0.efgh DW 11 Check Valve Cartridge[G]
	30.4013.0.efgh DW 13 KK Check Valve Cartridge[G]
	30.4014.0.efgh DW 14 Check Valve Cartridge[G]
	30.4016.0.efgh DW 16 Check Valve Cartridge[G]
	30.4019.0.efgh DW 19 Check Valve Cartridge[G]
	30.4031.0.efgh DW 14 GF AF Check Valve Cartridge[G]
	30.4032.0.efgh DW 14 I Check Valve Cartridge[G]
	30.4033.0.efgh DW 14 GF Check Valve Cartridge[G]
	30.4043.0.efgh DW 15 GF Check Valve Cartridge[G]
	30.4045.0.efgh DW 15 Check Valve Cartridge[G]
	30.4049.0.efgh DW 20 Check Valve Cartridge[G]
	30.4051.0.efgh DW 20 HF Check Valve Cartridge[G]
	30.4068.0.efgh DW 15 KK Check Valve Cartridge[G]
	30.4072.0.efgh DW14-GF HF Check Valve Cartridge[G]
	30.4073.0.efgh DW20/DN15 - 1T Check Valve Cartridge[G]
	30.4075.0.efgh DW20/DN15 - 1T - EPDM Check Valve Cartridge[G]
	31.0001.0.efgh OV15/DN15-EPDM[G]
	31.0002.0.efgh NV15/DN15-EPDM[G]
	31.0003.0.efgh OV20/DN20-EPDM[G]
	31.0005.0.efgh OV15/DN15-EPDM-5[G]
	31.0006.0.efgh OF15[G]
	31.0009.0.efgh NV25/DN25-EPDM[G]
	31.0011.0.efgh NV20-HT
	31.0012.0.efgh OV20-HT[G]
	31.0017.0.efgh NV32/DN32-EPDM[G]
	31.0019.0.efgh NV40/DN40-EPDM[G]
	31.0020.0.efgh NV50/DN50-EPDM[G]
	31.0022.0.efgh OV15-HT[G]
	31.0023.0.efgh NV20-EPDM-CA[G]
	31.0024.0.efgh OF15-HT[G]
	31.0025.0.egfh WV20/NV20-EPDM[G]
	31.0028.0.efgh OV25-HT[G]
	31.0030.0.efgh OV32-HT[G]
	31.0032.0.efgh OF15-EPDM[G]
	31.2004.1.efgh CV 15 FR 2,0 L[G]
	31.2006.1.efgh CV 15 FR 3,0 L[G]
	31.2007.1.efgh CV 15 FR 3,5 L[G]
	31.2008.1.efgh CV 15 FR 4,0 L[G]
	31.2010.1.efgh CV 15 FR 5,0 L[G]
	31.2011.1.efgh CV15-FR 1.5 GPM[G]
	31.2012.1.efgh CV 15 FR 6,0 L[G]
	31.2013.1.efgh CV15-FR 1.75 GPM[G]
	31.2014.1.efgh CV 15 FR 7,0 L[G]
	31.2015.1.efgh CV15-FR 2.0 GPM[G]
	31.2016.1.efgh CV 15 FR 8,0 L[G]
	31.2017.1.efgh CV 15 FR 2.2 gpm[G]
	31.2018.1.efgh CV 15 FR 9,0 L[G]
	31.2019.1.efgh CV 15 FR 2.5 gpm[G]
	31.2020.1.efgh CV 15 FR 10,0 L[G]
	31.2024.1.efgh CV 15 FR 12,0 L[G]
	31.2028.1.efgh CV 15 FR 14,0 L[G]
	31.2030.1.efgh CV 15 FR 15,0 L[G]
	31.2032.1.efgh CV15-FR 16.0 L[G]
	31.2220.0 FR-CV10 1.5 gpm[G]
	31.2221.0 FR-CV10 1.75 gpm[G]
	31.2222.0 FR-CV10 2.0 gpm[G]
	31.2223.0 FR-CV10 2.2 gpm[G]
	31.2224.0 FR-CV10 2.5 gpm[G]
	31.2231.0 FR-CV13 3,0L[G]
	31.2232.0 FR-CV13 4,0L[G]
	31.2233.0 FR-CV13 5,0L[G]
	31.2234.0 FR-CV13 6,0L[G]
	31.2235.0 FR-CV13 7,0L[G]
	31.2236.0 FR-CV13 8,0L[G]
	31.2237.0 FR-CV13 9,0L[G]
	31.2239.0 FR-CV13 12,0L[G]
	31.2243.0.efgh FR CV 12 1,9 L[G]
	31.2253.0.efgh FR CV 12 8,0 L[G]
	31.2254.0.efgh FR CV 12 9,0 L[G]
	31.2287.0.efgh FR CV 14 3,0 L[G]
	31.2288.0.efgh FR CV 14 4,0 L[G]
	31.2289.0.efgh FR CV 14 5,0 L[G]
	31.2290.0.efgh FR CV 14 6,0 L[G]
	31.2291.0.efgh FR CV 14 7,0 L[G]
	31.2293.0.efgh FR CV 14 8,0 L[G]
	31.2295.0.efgh FR CV 14 9,0 L[G]
	31.2297.0.efgh FR CV 14 12,0 L[G]
	31.3001.0.efgh CV 15-short[G]
	31.3200.0.efgh FR-CV15[G]
	31.3204.0.efgh FR CV 15 1,9 L[G]
	31.3210.0.efgh FR CV 15 5,0 L[G]
	31.3216.0.efgh FR CV 15 8,0 L[G]
	31.3218.0.efgh FR-CV 15 9,0 L[G]
	31.3220.0.efgh FR-CV 15 10,0 L[G]
	31.3224.0.efgh FR CV 15 12,0 L[G]
	31.4015.0.efgh CV 15[G]
	31.4025.0.efgh CV15-JR[G]
	31.4114.0.efgh CV 14[G]
	31.4134.0.efgh CV 14 AF[G]
	31.4144.0.efgh CV 14 FR 2,0 L[G]
	31.4146.0.efgh CV 14 FR 3,0 L[G]
	31.4147.0.efgh CV 14 FR 3,5 L[G]
	31.4148.0.efgh CV 14 FR 4,0 L[G]
	31.4150.0.efgh CV 14 FR 5,0 L[G]
	31.4151.0.efgh CV14-FR 1.5 GPM[G]
	31.4152.0.efgh CV 14 FR 6,0 L[G]
	31.4153.0.efgh CV14-FR 1.75 gpm[G]
	31.4154.0.efgh CV 14 FR 7,0 L[G]
	31.4155.0.efgh CV14-FR 2.0 gpm[G]
	31.4156.0.efgh CV 14 FR 8,0 L[G]
	31.4157.0.efgh CV14-FR 2.2 GPM[G]
	31.4158.0.efgh CV 14 FR 9,0 L[G]
	31.4159.0.efgh CV14-FR 2.5 GPM[G]
	31.4160.0.efgh CV 14 FR 10,0 L[G]
	31.4164.0.efgh CV 14 FR 12,0 L[G]
	31.4168.0.efgh CV 14 FR 14,0 L[G]
	31.4170.0.efgh CV 14 FR 15,0 L[G]
	31.4174.0.efgh CV 14 AF FR 2,0 L[G]
	31.4176.0.efgh CV 14 AF FR 3,0 L[G]
	31.4177.0.efgh CV 14 AF FR 3,5 L[G]
	31.4178.0.efgh CV 14 AF FR 4,0 L[G]
	31.4180.0.efgh CV 14 AF FR 5,0 L[G]
	31.4182.0.efgh CV 14 AF FR 6,0 L[G]
	31.4184.0.efgh CV 14 AF FR 7,0 L[G]
	31.4186.0.efgh CV 14 AF FR 8,0 L[G]
	31.4187.0.efgh CV14-AF-FR 2.2 GPM[G]
	31.4188.0.efgh CV 14 AF FR 9,0 L[G]
	31.4189.0.efgh CV14-AF-FR 2.5 GPM[G]
	31.4190.0.efgh CV 14 AF FR 10,0 L[G]
	31.4194.0.efgh CV 14 AF FR 12,0 L[G]
	31.4198.0.efgh CV 14 AF FR 14,0 L[G]
	31.4200.0.efgh CV 14 AF FR 15,0 L[G]
	31.4201.0.efgh Check Valve OD8/DN6[G]
	31.4204.0.efgh OF 10 JR-5[G]
	31.4206.0.efgh OF 10 JR[G]
	31.4207.0.efgh OV 10 JR OF[G]
	31.4208.0.efgh OF 10[G]
	31.4209.0.efgh OV 10 JR[G]
	31.4210.0.efgh OV10[G]
	31.4215.0.efgh OV 15[G]
	31.4216.0.efgh NV 15[G]
	31.4217.0.efgh WV 15[G]
	31.4220.0.efgh OV 20[G]
	31.4221.0.efgh NV 20[G]
	31.4222.0.efgh WV 20[G]
	31.4225.0.efgh OV 25[G]
	31.4226.0.efgh NV 25[G]
	31.4227.0.efgh WV 25[G]
	31.4232.0.efgh OV32[G]
	31.4233.0.efgh NV 32[G]
	31.4240.0.efgh OV40[G]
	31.4241.0.efgh NV 40[G]
	31.4246.0.efgh NV 40-5 CG[G]
	31.4251.0.efgh NV 50[G]
	31.4253.0.efgh NF 50[G]
	31.4264.0.efgh OD13/DN10[G]
	31.4315.0.efgh OV 15, 1.2 psi[G]
	31.4316.0.efgh NV 15, 1.2 psi[G]
	31.4320.0.efgh OV 20, 1.2 psi[G]
	31.4320.0.efgh OV20-1.2psi-EPDM[G]
	31.4321.0.efgh NV 20, 1.2 psi[G]
	31.4322.0.efgh OV20-1.2psi-EPDM-UW[G]
	31.4325.0.efgh OV 25, 1.2 psi[G]
	31.4326.0.efgh NV 25, 1.2 psi[G]
	31.4327.0.efgh OV25-1.2psi-EPDM-UW[G]
	31.4333.0.efgh NV 32, 1.2 psi[G]
	31.4341.0.efgh NV 40, 1.2 psi[G]
	31.4351.0.efgh NV 50, 1.2 psi[G]
	31.4433.0.efgh NV 32-F, PV B[G]
	31.4441.0.efgh NV 40-F, PV B[G]
	31.4451.0.efgh NV 50-F, PV B[G]
	31.4520.0.efgh OF20[G]
	31.4615.0.efgh OV 15, 1.5 psi[G]
	31.4815.0.efgh FR OV 15 UW[G]
	31.4816.0.efgh NV 15 UW[G]
	31.4820.0.efgh OV 20 UW[G]
	31.4821.0.efgh NV 20 UW[G]
	31.4825.0.efgh OV 25 UW[G]
	31.4826.0.efgh NV 25 UW[G]
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
[6] efgh - Packaging (0001 to 9999) consecutively numbered. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
Faucet, Pull-Out Hose Assembly
	39.86CD.EFG.HI Neoflex CRG[G] [14] [16] [17] [23]
	39.86CD.EFG.HI Neoflex CRG[14] [17] [18] [23]
	39.86CD.EFG.HI Neoflex CRG[G] [14] [15] [17] [21]
	39.88CD.EFG.HI GLIDEFLEX® Kitchen Pull-Out Hose[7]
[7] Fittings approved for use with this trade name: DN7.5 - M15 x 1, F 1/2", F1/2"-Swivel, F3/8"- Swivel, F5/8"-16mm Swivel, D9.5 plugin D14 , 9/16-12UNC-2A DN9.5 - M15 x 1, F 1/2", F1/2"-Swivel, D9.5 plugin D14 CD.EFG.HI may be any numeric value. [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%. [14] Size evaluated with this trade name: DN8 CD.EFG.HI may be any alpha-numeric value [15] Fittings evaluated with this trade name: MH CRG D8.5 Fitting 1/2 MH CRG D8.5 Fitting M15x1 A/F 1/2 [16] Hose length must be between 43" and 63". [17] Gaskets and o-rings have not been evaluated with MH CRG D8.5 fitting 1/2 and MH CRG D8.5 fitting M15x1 A/F 1/2. [18] Hose length must be between 43" and 78". [21] Certified to a maximum length of 78". [23] MH CRG D8.5 Fitting 1/2 MH CRG Assy D10 Plugin MH CRH D8.5 Fitting M15x1 A/F 1/2 MH CRG Assy 5/8-16 Swivel MH CRG Swivel 5/8-16 Cylindrical
Flexible Plumbing Connectors
	39.06CD.EFG.HI Neoflex CRG2.0[G] [24] [25] [26]
	39.06CD.EFG.HI Neoflex CRG2.0[24] [25] [27]
	39.9700.00100 RPE DN6 A1 313 LL plugD9 CooperStd[G]
	39.9700.00200 RPE DN6 A1 303 LL plugD9 CooperStd Black[G]
	39.ABCD.EFG.HI Neoflex SPX-HF[8] [9] [G] [10]
	39.ABCD.EFG.HI Neoflex SPX-NT[8] [9] [G] [19]
	39.ABCD.EFG.HI Neoperl Neoflex SPX[8] [9] [G] [12]
	39.ABCD.EFG.HI Neoperl Neoflex SPX Flexible Hose Connectors[8] [11] [20]
[8] Maximum length of hose is 78". [9] Size evaluated with this trade name: DN8 and DN6 A – May be 0-4 B – 0 SPX hose material CD.EFG – any number HI – Packaging information [G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%. [10] Fittings evaluated with this trade name: DN6HF M8X1 S M LF DN6HF M10X1 S M LF DN6HF TUBE D10 DI8 LF DN6HF RWG 3/8 LF DN6HF 3/8 LF DN6HF RWG 1/2F DN6HF CV 3/8 LF DN6HF CV 1/2 LF DN6HF M10X1 S M A/F10 LF DN6HF M10X1-LH S M A/F10 LF DN6HF TUBE D8 A/F10 LF DN6HF 2ORG D1,9 LF DN6HF RWG M15X1 LF DN6HF RWG 3/4F LF DN6HF RWG M15X1 F LF DN6HF 3/8 REVOLVING DN8HF 1/2 F LF DN8HF M10X1 S M LF DN8HF TUBE D10 DI8 LF DN8HF RWG 3/8 LF DN8HF 1/2 LF DN8HF CV 3/8 LF DN8HF CV 1/2 LF DN8HF M10X1 S M A/F10 LF DN8HF M10X1-LH S M A/F10 LF [11] Sizes approved with this trade name: DN6, DN8, DN10, and DN13. Naming convention: A – May be 0-4 B – (0) SPX hose material CD.EFG – Any number HI – Packaging information [12] Fittings evaluated with this trade name: DN6 C fitting plugin D9 LL DN6C Plugin D9 LL DN6C 9/16-24 UNEF 2B LL DN6 Assy RWG 3/8 f A/F19 LL DN6 Assy 1/2 f A/F24 fiber LL DN6 Assy M8x1 S m A/F10 LL DN8 fitting 1/2 m A/F21 LL DN8 Assy revolving 3/8 f A/F19 fiber LL DN8 Assy RWG 3/8 f A/F19 LL DN8 Assy RWG 1/2 f A/F24 LL DN8 Assy RWG 3/4 f A/F30 LL DN8 Assy M10x1 S m A/F11 LL [19] Fittings evaluated with this trade name: Brass DN6NT-HF fitting CV 3/8 f LF DN6NT-HF fitting RWG 3/8 f LF DN6NT-HF fitting 3/8 fibre A/F19 LF DN6NT-HF fitting 3/4 f LF DN6NT-HF fitting M10x1 S m LF DN6NT-HF fitting M8x1 S m LF DN6NT-HF fitting RWG 1/2 LF DN6NT-HF fitting 1/2 LF DN6NT-HF fitting CV 1/2 LF DN6NT-HF C fitting RWG 9/16-24 UNEF 2B DN6NT-HF fitting M10x1 S m A/F10 LF DN6NT-HF C fitting plugin D10 LF DN6NT-HF fitting M10x1-LH S m A/F10 LF DN6NT-HF C fitting M10x1 S m HS A/F7/32 DN6NT-HF C fitting M8x1 S m HS A/F5 DN6NT-HF C fitting RWG 3/8 f DN6NT-HF C fitting M8x1 S m LF DN6NT-HF C fitting M10x1 S m A/F10 LF DN6NT-HF C fitting M8x1 M m A/F10 LF DN6NT-HF C fitting plugin D10 LF DN6NT-HF C fitting plugin D10,6 DN6NT-HF C fitting plugin D9 LF DN6NT-HF C fitting plugin D10,6 DN6NT-HF C fitting plugin D10,7 DN8NT-HF fitting M10x1 S m A/F11 LF DN8NT-HF fitting 3/8 f LF DN8NT-HF fitting RWG 1/2 LF DN8NT-HF fitting RWG 3/8 LF DN8NT-HF fitting tube D10 di8 A/F10 LF DN8NT-HF fitting M10x1 S m A/F10 LF DN8NT-HF fitting 3/4 f LF DN8NT-HF fitting RWG 9/16-28 UNEF 2B LF DN8NT-HF fitting M10x1-LH A/F10 HSA/F6 LF DN8NT-HF fitting M10x1 S m LF DN8NT-HF fitting CV 3/8 LF DN8NT-HF fitting CV 1/2 LF DN8NT-HF fitting 1/2 LF DN8NT-HF fitting M10x1-LH S m A/F10 LF DN8NT-HF fitting tube D8 di6 A/F10 LF DN8NT-HF fitting elbow 3/4 f LF Stainless Steel DN6NT C fitting RWG 3/8 f DN6NT C fitting M6x0,75 A/F8 DN6NT C fitting M6x0,75 L m A/F8 DN6NT C fitting plugin D9,45 di1,6 DN6NT C fitting plugin D9,45 DN6NT C fitting tube D8 di6 L24 DN6NT C fitting RWG 3/8 f [20] Fittings approved with this trade name: DN6 Assy RWG 3/8 f A/F19 DN6 Assy 1/2 f A/F24 fiber DN6 Assy M10x1 S m A/F11 DN6 Assy M10x1 L m A/F11 DN6 Assy M8x1 S m A/F10 DN6 Assy M10x1 XL m A/F11 DN6 Fitting tube D8 A/F10 DN6 Fitting tube D10 A/F11 DN8 Assy revolving 3/8 f A/F19 fiber DN8 Assy RWG 3/8 f A/F19 DN8 Assy RWG 1/2 f A/F24 DN8 Assy RWG 3/4 f A/F30 DN8 Assy M10x1 S m A/F11 DN8 Assy M10x1 L m A/F11 DN8 Assy M10x1 XL m A/F11 DN8 C Assy M10x1 XL m A/F11 DN8 C fitting M10x1 S m DN8 Assy RWG elbow 3/8f A/F19 DN8 Assy RWG elbow 1/2 f A/F24 DN8 Assy RWG elbow 3/4 f A/F30 DN8 Assy Compression fitting D10 3/8 A/F19 DN8 Assy Compression fitting D8 3/8 A/F19 DN8 Fitting 1/2 m A/F21 DN8 Fitting 1/2 m A/F21 DR DN8 Fitting tube A10 A/F11 DN8 Fitting tube D10 A/F11 DN8 C fitting tube M10x1 m DR DN10 Assy RWG 1/2 F A/F24 DN10 Assy RWG 3/4 F A/F30 DN10 Assy RWG elbow 1/2 F A/F24 DN10 Assy RWG elbow 3/4 F A/F30 DN10 Fitting 1/2 m A/F21 DN10 Fitting 3/4 m A/F27 DN10 Fitting tube D12 A/F13 DN13 C Fitting groove 1/2 m DR DN13 C Assy ORG 1/2 F A/F24 DR DN13 C Fitting R1/2 m A/F22 DR [24] Size evaluated with this trade name: DN8 CD.EFG.HI may be any alpha-numeric value [25] Fittings (CRG2.0 DN8) evaluated with this trade name: RWG 3/8 f tube D10 RWG 1/2 f RWG elbow 3/8 f 1/2 m A/F21 3/4 f revolving 3/8 f 3/8 m D10 A/F17 3/8 m D8 A/F17 3/8 m for rev. compD10 M10x1 S m A/F10 [26] Hose length must be between 45" and 78". [27] Hose length must be less than 45".
Hose
	GLIDEFLEX®[13]
[13] Certified for inner diameter of 7.5mm and 9.5mm and a maximum length of 2000mm.
Miscellaneous Faucet Components
	07.8152.0 VARIO T5 PCR 1.5gpm f.55/64 Chrome plated
	07.8154.0 VARIO T5 PCR 1.5gpm f.55/64 White
	18.0301.0: Ecobooster-Faucet M24 7,0L CC-SLC-M24-B
	18.0305.0: Ecobooster-Faucet M22 7,0L CC-SLC-M24-B
	18.0322.0: Ecobooster-Faucet M22 5,0L CC-SLC-M24-B
	18.0323.0: Ecobooster-Faucet M24 5,0L CC-SLC-M24-B
	18.0331.0: Ecobooster-Faucet M22-M24 7,0L CC-STD-M24x1-B
	18.0332.0: Ecobooster-Faucet M22 7,0L CON CC-SLC-M24-B
	18.0335.0: Ecobooster-Faucet M22 5,0L CON CC-SLC-M24-B
	18.0336.0: Ecobooster-Faucet 55-64 UNS 1.5gpm CC-SLC-M24-2.2 gpm
	58.6156.0 SHS-C Flow Regulator[G]
	58.6157.0 SHL-B Flow Regulator[G]
	58.6158.0 SHL-C Flow Regulator[G]
	58.6266.1 E-NT 16.0 L Flow Regulator[G]
	58.6267.1 E-NT 5.0 L Flow Regulator[G]
	58.6268.1 E-NT 6.0 L Flow Regulator[G]
	58.6269.1 E-NT 7.0 L Flow Regulator[G]
	58.6270.1 E-NT 11.0 L Flow Regulator[G]
	58.6271.1 E-NT 8.0 L Flow Regulator[G]
	58.6272.1 E-NT 9.0 L Flow Regulator[G]
	58.6273.1 E-NT 10.0 L Flow Regulator[G]
	58.6274.1 E-NT 12.0 L Flow Regulator[G]
	58.6275.1 E-NT 13.0 L Flow Regulator[G]
	58.6276.1 E-NT 14.0 L Flow Regulator[G]
	58.6277.1 E-NT 15.0 L Flow Regulator[G]
	58.6278.1 E-NT 1.0 L Flow Regulator[G]
	58.6279.1 E-NT 2.0 L Flow Regulator[G]
	58.6280.1 E-NT 3.0 L Flow Regulator[G]
	58.6281.1 E-NT 4.0 L Flow Regulator[G]
	58.6282.1 E-NT 17.0 L Flow Regulator[G]
	58.6283.1 E-NT 18.0 L Flow Regulator[G]
	58.6284.1 E-NT 19.0 L Flow Regulator[G]
	58.6285.1 E-NT 26.5 L Flow Regulator[G]
	58.6301.1 MR03 0.25 L Flow Regulator[G]
	58.6302.1 MR03 0.5 L Flow Regulator[G]
	58.6303.1 MR03 1.0 L Flow Regulator[G]
	58.6304.1 MR03 1.9 L Flow Regulator[G]
	58.6305.1 MR03 5.0 L Flow Regulator[G]
	58.6306.1 MR03 6.0L Flow Regulator Assembly[G]
	58.6308.1 MR03 8.0L Flow Regulator Assembly[G]
	58.6309.1 MR03 9.0 L Flow Regulator[G]
	58.6310.1 MR03 4.0 L Flow Regulator[G]
	58.6311.1 MR03 2.5 L Flow Regulator[G]
	58.6316.1 E-NT 22.0 L Flow Regulator[G]
	58.6354.1 MR03 FG 4.0 L Flow Regulator[G]
	58.6355.1 MR03 FG 5.0 L Flow Regulator[G]
	58.6356.1 MR03 FG 6.0 L Flow Regulator[G]
	58.6357.1 MR03 FG 7.0 L Flow Regulator[G]
	58.6358.1 MR03 FG 8.0 L Flow Regulator[G]
	58.6359.1 MR03 FG 9.0 L Flow Regulator[G]
	58.6381.1 MR03-PG 0.5 gpm Flow Regulator[G]
	58.6385.1 MR03 PF-1.5 gpm Flow Regulator[G]
	58.6500.1 MR05 1,7L Flow Regulator[G]
	58.6501.1 MR05 0,5L Flow Regulator[G]
	58.6502.1 MR05 0,7L Flow Regulator[G]
	58.6503.1 MR05 1,0L Flow Regulator[G]
	58.6504.1 MR05 1,4L Flow Regulator[G]
	58.6505.1 MR05 1,9L Flow Regulator[G]
	58.6506.1 MR05 2,5L Flow Regulator[G]
	58.6507.1 MR05 3,0L Flow Regulator[G]
	58.6508.1 MR05 3,5L Flow Regulator[G]
	58.6509.1 MR05 4,0L Flow Regulator[G]
	58.6510.1 MR05 5,0L Flow Regulator[G]
	58.6512.1 MR05 6,0L Flow Regulator[G]
	58.6514.1 MR05 7,0L Flow Regulator[G]
	58.6515.1 MR05 7,3L Flow Regulator[G]
	58.6516.1 MR05 8,0L Flow Regulator[G]
	58.6517.1 MR05 8,3L Flow Regulator[G]
	58.6518.1 MR05 9,0L Flow Regulator[G]
	58.6520.1 MR05 10,0L Flow Regulator[G]
	58.6524.1 MR05 12,0L Flow Regulator[G]
	58.6527.1 MR05 14,0L Flow Regulator[G]
	58.6528.1 MR05 2,75L Flow Regulator[G]
	58.6640.1 L 20,0L Flow Regulator[G]
	58.6645.1 L 25,0L Flow Regulator[G]
	58.6646.1 L 30,0L Flow Regulator[G]
	58.6647.1 L 35,0L Flow Regulator[G]
	58.6648.1 L 38,0L Flow Regulator[G]
	58.6650.1 L 50,0L Flow Regulator[G]
	58.6655.1 L 70,0L Flow Regulator[G]
	58.6658.1 L 90,0L Flow Regulator[G]
	58.6660.1 L 100,0L Flow Regulator[G]
	58.7085.1 MR05 US 0.5 gpm Flow Regulator[G]
	58.7086.1 MR05 US 0.74 gpm Flow Regulator[G]
	58.7087.1 MR05 US 2.5 gpm Flow Regulator[G]
	58.7088.1 MR05 US 2.2 gpm Flow Regulator[G]
	58.7089.1 MR05 US 1.5 gpm Flow Regulator[G]
	58.7090.1 MR05 US 1.75 gpm Flow Regulator[G]
	58.7091.1 MR05 US 2.0 gpm Flow Regulator[G]
	58.7092.1 MR05 US 1.0 gpm Flow Regulator[G]
	58.7349.1 F-NT 22.0 L Flow Regulator[G]
	58.7350.1 F-NT 26,5 L Flow Regulator[G]
	58.7351.1 F-NT 1,0 L Flow Regulator[G]
	58.7352.1 F-NT 2,0 L Flow Regulator[G]
	58.7353.1 F-NT 3,0 L Flow Regulator[G]
	58.7354.1 F-NT 4,0 L Flow Regulator[G]
	58.7355.1 F-NT 5,0 L Flow Regulator[G]
	58.7356.1 F-NT 6,0 L Flow Regulator[G]
	58.7357.1 F-NT 7,0 L Flow Regulator[G]
	58.7358.1 F-NT 8,0 L Flow Regulator[G]
	58.7359.1 F-NT 9,0 L Flow Regulator[G]
	58.7360.1 F-NT 10,0 L Flow Regulator[G]
	58.7361.1 F-NT 11,0 L Flow Regulator[G]
	58.7362.1 F-NT 12,0 L Flow Regulator[G]
	58.7363.1 F-NT 13,0 L Flow Regulator[G]
	58.7364.1 F-NT 14,0 L Flow Regulator[G]
	58.7365.1 F-NT 15,0 L Flow Regulator[G]
	58.7366.1 F-NT 16,0 L Flow Regulator[G]
	58.7370.1 F-NT 20,0 L Flow Regulator[G]
	58.7401.1 G-NT 1,0 L Flow Regulator[G]
	58.7402.1 G-NT 2,0 L Flow Regulator[G]
	58.7403.1 G-NT 3,0 L Flow Regulator[G]
	58.7404.1 G-NT 4,0 L Flow Regulator[G]
	58.7405.1 G-NT 5,0 L Flow Regulator[G]
	58.7406.1 G-NT 6,0 L Flow Regulator[G]
	58.7407.1 G-NT 7,0 L Flow Regulator[G]
	58.7408.1 G-NT 8,0 L Flow Regulator[G]
	58.7409.1 G-NT 9,0 L Flow Regulator[G]
	58.7410.1 G-NT 10,0 L Flow Regulator[G]
	58.7411.1 G-NT 11,0 L Flow Regulator[G]
	58.7412.1 G-NT 12,0 L Flow Regulator[G]
	58.7413.1 G-NT 13,0 L Flow Regulator[G]
	58.7414.1 G-NT 14,0 L Flow Regulator[G]
	58.7415.1 G-NT 15,0 L Flow Regulator[G]
	58.7416.1 G-NT 16,0 L Flow Regulator[G]
	58.7418.1 G-NT 18,0 L Flow Regulator[G]
	58.7420.1 G-NT 20.0 L Flow Regulator[G]
	58.7458.1 L-US 10,0 USG MAX Flow Regulator[G]
	58.7459.1 L-US 12.0 USG max. Flow Regulator[G]
	58.7460.1 L-US 13,0 USG MAX Flow Regulator[G]
	58.7462.1 L-US 15.0 USG max. Flow Regulator[G]
	58.7463.1 L-US 20,0 USG MAX Flow Regulator[G]
	58.7465.1 L-US 25,0 USG MAX Flow Regulator[G]
	58.7468.1 L-US 30,0 USG MAX Flow Regulator[G]
	58.7560.1 E-US 1.5 USG MAX Flow Regulator[G]
	58.7561.1 E-US 1.75 USG MAX Flow Regulator[G]
	58.7562.1 E-US 2.2 USG MAX Flow Regulator[G]
	58.7563.1 E-US 2.5 USG MAX Flow Regulator[G]
	58.7564.1 E-US 2.0 USG MAX Flow Regulator[G]
	58.7565.1 E-US 1.25 USG max. Flow Regulator[G]
	58.7570.1 F-US 1.5 gpm Flow Regulator[G]
	58.7571.1 F-US 1.75 gpm Flow Regulator[G]
	58.7572.1 F-US 2.2 gpm Flow Regulator[G]
	58.7573.1 F-US 2.5 gpm Flow Regulator[G]
	58.7574.1 F-US 2.0 gpm Flow Regulator[G]
	58.7579.1 G-US 1.25 USG max. Flow Regulator[G]
	58.7580.1 G-US 1,5 USG MAX Flow Regulator[G]
	58.7581.1 G-US 1,75 USG MAX Flow Regulator[G]
	58.7582.1 G-US 2,2 USG MAX Flow Regulator[G]
	58.7583.1 G-US 2,5 USG MAX Flow Regulator[G]
	58.7584.0 G-US 2.0 USG MAX Flow Regulator[G]
	58.7830.1 H-NT 0,5 USG MAX Flow Regulator[G]
	58.7831.1 H-NT 0,75 USG MAX Flow Regulator[G]
	58.7832.1 H-NT 1,5 USG MAX Flow Regulator[G]
	58.7833.1 H-NT 1,75 USG MAX Flow Regulator[G]
	58.7834.1 H-NT 2,2 USG MAX Flow Regulator[G]
	58.7835.1 H-NT 2,5 USG MAX Flow Regulator[G]
	58.7836.1 H-NT2,0 USG MAX Flow Regulator[G]
	58.8131.1 E-T 2.0 L Flow Regulator[G]
	58.8132.1 E-T 3.0 L Flow Regulator[G]
	58.8133.1 E-T 3.5 L Flow Regulator[G]
	58.8134.1 E-T 4.0 L Flow Regulator[G]
	58.8135.1 E-T 5.0 L Flow Regulator[G]
	58.8137.1 E-T 7.0 L Flow Regulator[G]
	58.8138.1 E-T 2.15 L Flow Regulator[G]
	58.8139.1 E-T 9.0 L Flow Regulator[G]
	58.8140.1 E-T 10.0 L Flow Regulator[G]
	58.8142.1 E-T 12.0 L Flow Regulator[G]
	58.8371.1 H-NT 2,0L Flow Regulator[G]
	58.8372.1 H-NT 3,0L Flow Regulator[G]
	58.8373.1 H-NT 3,5L Flow Regulator[G]
	58.8374.1 H-NT 4,0L Flow Regulator[G]
	58.8375.1 H-NT 5,0L Flow Regulator[G]
	58.8376.1 H-NT 6,0L Flow Regulator[G]
	58.8377.1 H-NT 7,0L Flow Regulator[G]
	58.8378.1 H-NT 8,0 L Flow Regulator[G]
	58.8379.1 H-NT 9,0L Flow Regulator[G]
	58.8380.1 H-NT 10,0L Flow Regulator[G]
	58.8381.1 H-NT 11.0 L Flow Regulator[G]
	58.8382.1 H-NT 12,0L Flow Regulator[G]
	58.8385.1 H-NT 22.5 L Flow Regulator[G]
	58.8533.1 MR03-US 1.0 gpm Flow Regulator[G]
	58.8535.1 MR03-US 1.5 gpm Flow Regulator[G]
	58.8536.1 MR03-US 1.75 gpm Flow Regulator[G]
	58.8537.1 MR03-US 2.0 gpm Flow Regulator[G]
	58.8632.1 PCW-1/2" 14.0 L[G]
	58.8633.1 PCW-1/2" 3.0 L[G]
	58.8634.1 PCW-1/2" 4.0 L[G]
	58.8635.1 PCW-1/2" 5.0 L[G]
	58.8636.1 PCW-1/2" 6.0 L[G]
	58.8637.1 PCW-1/2" 7.0 L[G]
	58.8638.1 PCW-1/2" 8.0 L[G]
	58.8639.1 PCW-1/2" 9.0 L[G]
	58.8640.1 PCW-1/2" 10.0 L[G]
	58.8641.1 PCW-1/2" 11.0 L[G]
	58.8642.1 PCW-1/2"’ 12.0 L[G]
	58.8643.1 PCW-1/2" 0.5 gpm[G]
	58.8644.1 PCW-1/2" 1.0 gpm[G]
	58.8645.1 PCW-1/2" 1.5 gpm[G]
	58.8646.1 PCW-1/2" 1.75 gpm[G]
	58.8647.1 PCW-1/2" 2.0 gpm[G]
	58.8648.1 PCW-1/2" 2.2 gpm[G]
	58.8649.1 PCW-1/2" 2.5 gpm[G]
	58.8650.1 PCW-1/2" 15.0 L[G]
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
Valves[G]
	30.3000.0 SV 15 Check Valve
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Neoperl Spare Parts
171 Mattatuck Heights
Waterbury, CT 06705-3832
United States
203-756-8891

Facility : Waterbury, CT

Mechanical Plumbing Devices

	Trade Designation
Aerators[G]
Best Plumbing Specialty
	50469XX Perlator Honeycomb 1.5 gpm
Brasscraft
	PB042 Home Plumber Water Saving Aerator 1.5 gpm
	PB042 Home Plumber Water Saving Aerator 1.5 gpm
	PRL025 Peerless Low Flow Aerator 1.5gpm
	PRL026 Peerless Low Flow Aerator 1.5gpm
	SF0114 BrassCraft Low Flow Aerator 1.5gpm
	SF0304 BrassCraft Low Flow Male Aerator 1.5gpm
	SF0305 BrassCraft Low Flow Female Aerator 1.5gpm
	SF0306 BrassCraft Dual Thread Aerator 1.5 gpm
	SF0323 BrassCraft Dual Thread Aerator 1.5 gpm
	SF0324 BrassCraft Dual Thread Aerator 1.5 gpm
Conservation Management Solutions
	50476XX PCA Perlator Honeycomb AC 1.5 gpm
	50477XX PCA Perlator Honeycomb AC 1.5 gpm
	50516XX PCA Perlator Honeycomb 1.5 gpm
	50517XX PCA Perlator Honeycomb 1.5 gpm
	50518XX PCA Perlator Honeycomb 1.0 gpm
	50519XX PCA Perlator Honeycomb 1.0 gpm
Corona
	298991 PCA Perlator, 1.0 GPM
	298992 PCA Perlator, 1.0 GPM
	298993 PCA Perlator, 1.0 GPM, LAM
	298994 PCA Perlator, 1.0 GPM, LAM
Grainger
	55001XX PCA Perlator Honeycomb 1.0 gpm
	55002XX Perlator Honeycomb 1.5 gpm
	55006XX PCA Perlator Honeycomb 1.0 gpm
	55007XX Perlator Honeycomb 1.5 gpm
	55011XX PCA Perlator Honeycomb 1.0 gpm
	55012XX Perlator Honeycomb 1.5 gpm
	55015XX Perlator Honeycomb Junior 1.5 gpm
	55017XX Perlator Honeycomb Junior 1.5 gpm
	55019XX PCA Perlator Honeycomb 1.5 gpm
	55024XX Perlator Honeycomb 1.5 gpm
	55027XX Perlator Honeycomb 1.5 gpm
	55046XX PCA Perlator Honeycomb 1.0 gpm
	55047XX Perlator Honeycomb 1.5 gpm
	55050XX Perlator Honeycomb Junior 1.5 gpm
	55053XX PCA Perlator Honeycomb 1.0 gpm
	55054XX Perlator Honeycomb 1.5 gpm
	55058XX Perlator Honeycomb 1.5 gpm
	55060XX PCA Perlator Honeycomb 1.0 gpm
HD Supply
	50010XX Perlator Honeycomb 1.5 gpm
	50012XX PCA Perlator Honeycomb 1.0 gpm
	50015XX Perlator Honeycomb 1.5 gpm (Sample Bag)
	50023XX Perlator Honeycomb Junior 1.5 gpm
	50024XX Perlator Honeycomb Junior 1.5 gpm
	50029XX Perlator Honeycomb 1.5 gpm
	50030XX Perlator Honeycomb 1.5 gpm
	50031XX Perlator Honeycomb 1.5 gpm
	50037XX PCA Perlator Honeycomb 1.0 gpm
	50043XX Perlator Honeycomb 1.5 gpm (Pro Kit)
	50047XX Perlator Honeycomb 1.5 gpm
	50048XX Perlator Honeycomb 1.5 gpm
	50066XX PCA Perlator Honeycomb AC 1.5 gpm
	50071XX PCA Perlator 1.0 gpm and Perlator 1.0 gpm (HDS Ideally Green kit)
	50077XX Perlator Honeycomb 1.5 gpm
MJSI
	9014905 Aerator Perlator Honeycomb 1.5 gpm
	9015105 Aerator Perlator Honeycomb 1.5 gpm
Magic-Tech
	50433XX PCA Perlator Honeycomb 1.0 gpm
	50434XX PCA Perlator Honeycomb 1.0 gpm
	50435XX PCA Perlator Honeycomb 1.0 gpm
	50466XX PCA Perlator Honeycomb 1.0 gpm
	50470XX PCA Perlator Honeycomb Junior 1.0 gpm
	50478XX PCA Perlator Honeycomb Junior 1.0 gpm
Mark's Plumbing Parts
	50513XX Aerator Perlator Honeycomb 1.5 gpm
	50515XX Aerator Perlator Honeycomb 1.5 gpm
	50522XX Aerator Perlator Honeycomb 1.5 gpm
	50532XX Aerator Perlator Honeycomb 1.5 gpm
	50533XX Aerator Perlator Honeycomb Junior 1.5 gpm
	50534XX Aerator Perlator Honeycomb Junior 1.5 gpm
	50537XX Aerator Perlator Honeycomb 1.5 gpm
	50538XX Aerator Perlator Honeycomb Junior 1.5 gpm
	50560XX Aerator PCA Perlator Honeycomb Junior 1.5 gpm
	50561XX Aerator PCA Perlator Honeycomb Junior 1.5 gpm
	50564XX Aerator PCA Perlator Honeycomb Junior 1.5 gpm
	50566XX Aerator Cascade SLC 1.5 gpm
	50567XX Aerator Cascade SLC 1.5 gpm
NEOPERL
	10600XX Perlator Honeycomb Aerator 1.5 gpm
	10602XX Perlator Honeycomb Aerator 1.5 gpm
	10603XX Perlator Honeycomb Aerator 1.5 gpm
	10604XX Perlator Honeycomb Aerator 1.5 gpm
	10610XX Perlator Honeycomb Aerator 1.5 gpm
	10612XX Perlator Honeycomb Aerator 1.5 gpm
	10614XX Perlator Honeycomb Aerator 1.5 gpm
	10620XX Perlator Honeycomb Aerator 1.5 gpm
	10622XX Perlator Honeycomb Aerator 1.5 gpm
	10624XX Perlator Honeycomb Aerator 1.5 gpm
	10625XX Perlator Honeycomb Aerator 1.5 gpm
	10635XX Perlator Honeycomb Insert 1.5 gpm
	10640XX Perlator Honeycomb Aerator 1.5 gpm
	10665XX Perlator Honeycomb Junior Insert 1.5 gpm
	10670XX Perlator Honeycomb Junior Aerator 1.5 gpm
	10674XX Perlator Honeycomb Junior Aerator 1.5 gpm
	10675XX Perlator Honeycomb Junior Aerator 1.5 gpm
	10680XX Perlator Honeycomb Junior Aerator 1.5 gpm
	10684XX Perlator Honeycomb Junior Aerator 1.5 gpm
	10691XX Perlator Honeycomb Aerator 1.5 gpm
	11100XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11104XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11110XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11114XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11120XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11124XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11125XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11135XX PCA Perlator Honeycomb Insert 1.5 gpm
	11165XX PCA Perlator Honeycomb Junior Insert 1.5 gpm
	11170XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm
	11174XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm
	11180XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm
	11184XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm
	11191XX PCA Perlator Honeycomb Aerator 1.5 gpm
	11195XX PCA Perlator Honeycomb Tom Thumb Insert 1.5 gpm
	11196XX PCA Perlator Honeycomb Tom Thumb Aerator 1.5 gpm
	11197XX PCA Perlator Honeycomb Tom Thumb Aerator 1.5 gpm
	11300XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11304XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11308XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11310XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11314XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11318XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11320XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11325XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11335XX PCA Perlator Honeycomb Insert 1.5 gpm Laminar
	11365XX PCA Perlator Honeycomb Junior Insert 1.5 gpm Laminar
	11370XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm Laminar
	11374XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm Laminar
	11380XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm Laminar
	11384XX PCA Perlator Honeycomb Junior Aerator 1.5 gpm Laminar
	11391XX PCA Perlator Honeycomb Aerator 1.5 gpm Laminar
	11395XX PCA Perlator Honeycomb Tom Thumb Insert 1.5 gpm Laminar
	11396XX PCA Perlator Honeycomb Tom Thumb Aerator 1.5 gpm Laminar
	11397XX PCA Perlator Honeycomb Tom Thumb Aerator 1.5 gpm Laminar
	11700XX PCA Perlator Honeycomb Aerator 1.0 gpm
	11704XX PCA Perlator Honeycomb Aerator 1.0 gpm
	11710XX PCA Perlator Honeycomb Aerator 1.0 gpm
	11714XX PCA Perlator Honeycomb Aerator 1.0 gpm
	11720XX PCA Perlator Honeycomb Aerator 1.0 gpm
	11724XX PCA Perlator Honeycomb Aerator 1.0 gpm
	11725XX PCA Perlator Honeycomb Aerator 1.0 gpm
	11735XX PCA Perlator Honeycomb Insert 1.0 gpm
	11765XX PCA Perlator Honeycomb Junior Insert 1.0 gpm
	11770XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm
	11774XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm
	11780XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm
	11784XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm
	11795XX PCA Perlator Honeycomb Tom Thumb Insert 1.0 gpm
	11796XX PCA Perlator Honeycomb Tom Thumb Aerator 1.0 gpm
	11798XX PCA Perlator Honeycomb Tom Thumb Aerator 1.0 gpm
	11800XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11804XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11810XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11814XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11820XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11824XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11825XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11835XX PCA Perlator Honeycomb Insert 1.0 gpm Laminar
	11865XX PCA Perlator Honeycomb Junior Insert 1.0 gpm Laminar
	11870XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm Laminar
	11874XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm Laminar
	11880XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm Laminar
	11884XX PCA Perlator Honeycomb Junior Aerator 1.0 gpm Laminar
	11891XX PCA Perlator Honeycomb Aerator 1.0 gpm Laminar
	11895XX PCA Perlator Tom Thumb Insert 1.0 gpm Laminar
	11896XX PCA Perlator Tom Thumb Aerator 1.0 gpm Laminar
	11897XX PCA Perlator Tom Thumb Aerator 1.0 gpm Laminar
	12400XX PCA Cascade SLC Aerator 1.5 gpm
	12410XX PCA Cascade SLC Aerator 1.5 gpm
	12420XX PCA Cascade SLC Aerator 1.5 gpm
	12435XX PCA Cascade SLC Insert 1.5 gpm
	12920XX Vario Kitchen Spray PCA 1.5 gpm
	12926XX Vario Kitchen Spray PCA 1.5 gpm
	13004XX Cache Perlator Honeycomb Junior 1.5 gpm
	13005XX Cache Perlator Honeycomb 1.5 gpm
	13007XX Cache Perlator Honeycomb Tiny Junior 1.5 gpm
	13023XX Cache PCA Perlator Honeycomb Tom Thumb 1.5 gpm
	13024XX Cache PCA Perlator Honeycomb Tiny Junior 1.5 gpm
	13025XX Cache PCA Perlator Honeycomb Junior 1.5 gpm
	13026XX Cache PCA Perlator Honeycomb 1.5 gpm
	13027XX Cache PCA Perlator Honeycomb Tom Thumb 1.0 gpm
	13028XX Cache PCA Perlator Honeycomb Junior 1.0 gpm
	13030XX Cache PCA Perlator Honeycomb Junior 1.5 gpm Laminar
	13031XX Cache PCA Perlator Honeycomb 1.5 gpm Laminar
	13032XX Cache PCA Perlator Honeycomb Tiny Junior 1.5 gpm Laminar
	13033XX Cache PCA Perlator Honeycomb Tom Thumb 1.5 gpm Laminar
	13034XX Cache PCA Perlator Honeycomb Tom Thumb 1.0 gpm Laminar
	13200XX Cascade SLC Aerator 1.5 gpm
	13210XX Cascade SLC Aerator 1.5 gpm
	13220XX Cascade SLC Aerator 1.5 gpm
	13235XX Cascade SLC Insert 1.5 gpm
	30100XX Perlator Honeycomb SSR Aerator 1.5 gpm
	30110XX Perlator Honeycomb SSR Aerator 1.5 gpm
	30135XX Perlator Honeycomb SSR Insert 1.5 gpm
	30600XX PCA Perlator Honeycomb AC Aerator 1.5 gpm
	30610XX PCA Perlator Honeycomb AC Aerator 1.5 gpm
	30620XX PCA Perlator Honeycomb AC Aerator 1.5 gpm
	30635XX PCA Perlator Honeycomb AC Insert 1.5 gpm
	50002XX Perlator Honeycomb Insert 1.5 gpm (Sample bag)
	50416XX Perlator Honeycomb Aerator 1.5 gpm (Sample bag)
New Resources Group
	50421XX Perlator Honeycomb, 1.5 gpm Std Aerator
Plumb Pak
	99800-111LF PlumbPak, Faucet Aerator, 1.5 gpm
	99800-211LF PlumbPak, Faucet Aerator, 1.5 gpm
	PP800-102LF PlumbPak, Faucet Aerator insert, 1.5 gpm
	PP800-105BNLF PlumbPak, Faucet Aerator, 1.5 gpm
	PP800-105LF PlumbPak, Faucet Aerator, 1.5 gpm
	PP800-106LF PlumbPak, Faucet Aerator Antimicrobial, 1.5 gpm

NSF Product and Service Listings