These NSF Official Listings are current as of Friday, May 24, 2013 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://www.nsf.org/Certified/PwsComponents/Listings.asp?Company=00190&Standard=061&
NSF/ANSI STANDARD 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings.
| 3M / Infrastructure Protection Division |  |
| 3M Center, Building 201-2C-11 | |
| St. Paul, MN 55144 | |
| United States | |
| 651-736-9030 | |
| Visit this company's website |
Facility : Minnetonka, MN
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| ScotchKote 323[1] | >= 2" | CLD 23 | EPOXY | |
| Scotchkote 323C[1] | >= 2" | CLD 23 | EPOXY | |
| Scotchkote 323P[1] | >- 2" | CLD 23 | EPOXY | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 30
Maximum Thinner: None
Final Cure Time and Temperature: 120°F for 2 hours
Special Comments: Mix ratio of A:B is 2:1 by volume.
|
||||
|
Coatings - Pipe |
||||
| ScotchKote 323[1] | >= 2" | CLD 23 | EPOXY | |
| Scotchkote 323C[1] | >= 2" | CLD 23 | EPOXY | |
| Scotchkote 323P[1] | >= 2" | CLD 23 | EPOXY | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 30
Maximum Thinner: None
Final Cure Time and Temperature: 120°F for 2 hours
Special Comments: Mix ratio of A:B is 2:1 by volume.
|
||||
|
Coatings - Tank |
||||
| ScotchKote 323[1] | >= 50 gal. | CLD 23 | EPOXY | |
| Scotchkote 323C[1] | >= 50 gal. | CLD 23 | EPOXY | |
| Scotchkote 323P[1] | >= 50 gal. | CLD 23 | EPOXY | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 30
Maximum Thinner: None
Final Cure Time and Temperature: 120°F for 2 hours
Special Comments: Mix ratio of A:B is 2:1 by volume.
|
||||
|
Coatings - Valve |
||||
| ScotchKote 323[1] | >= 2" | CLD 23 | EPOXY | |
| Scotchkote 323C[1] | >= 2" | CLD 23 | EPOXY | |
| Scotchkote 323P[1] | >= 2" | CLD 23 | EPOXY | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 30
Maximum Thinner: None
Final Cure Time and Temperature: 120°F for 2 hours
Special Comments: Mix ratio of A:B is 2:1 by volume.
|
||||
Facility : Angleton, TX
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134[2] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 1/2" | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 4" | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 4" | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 4" | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 4" | D. HOT | PEC | |
[1] Colors: Dark Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum thinner: None
Final Cure Time and Temperature: 6233 4G/6233W 4G: 40 seconds at 450°F; 6233 8G/6233W
8G: 90 seconds at 450°F; 6233 11G/6233W 11G: 110 seconds at 450°F
Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400°F
|
||||
|
Coatings - Pipe |
||||
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134[2] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 1/2" | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 4" | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 4" | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 4' | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 4" | D. HOT | PEC | |
[1] Colors: Dark Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum thinner: None
Final Cure Time and Temperature: 6233 4G/6233W 4G: 40 seconds at 450°F; 6233 8G/6233W
8G: 90 seconds at 450°F; 6233 11G/6233W 11G: 110 seconds at 450°F
Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400°F
|
||||
|
Coatings - Pump |
||||
| ScotchKote 134[2] | [4] | D. HOT | PEC | |
| ScotchKote 134W[2] | [4] | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 2"[4] | D. HOT | PEC | |
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400°F
[4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
use.
|
||||
|
Coatings - Tank |
||||
| ScotchKote 134[2] | >= 5 gal. | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N[3] [4] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] [4] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] [4] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] [4] | >= 5 gal. | D. HOT | PEC | |
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400°F
[4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
use.
|
||||
|
Coatings - Valve |
||||
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134[2] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 1/2" | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 2" | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 2" | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 2" | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 2" | D. HOT | PEC | |
[1] Colors: Dark Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum thinner: None
Final Cure Time and Temperature: 6233 4G/6233W 4G: 40 seconds at 450°F; 6233 8G/6233W
8G: 90 seconds at 450°F; 6233 11G/6233W 11G: 110 seconds at 450°F
Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400°F
|
||||
Facility : Morden, Manitoba, Canada
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134[2] | >= 1/2"[4] | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 1/2"[4] | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 4"[4] | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 4"[4] | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 4"[4] | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 4"[4] | D. HOT | PEC | |
[1] Colors: Dark Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: None
Final Cure Time and Temperature: 6233 4G/6233W 4G: 40 seconds at 450°F; 6233 8G/6233W
8G: 90 seconds at 450°F; 6233 11G/6233W 11G: 110 seconds at 450°F
Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425° F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400° F
[4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
use.
|
||||
|
Coatings - Pipe |
||||
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134[2] | >= 1/2"[4] | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 1/2"[4] | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 4"[4] | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 4"[4] | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 4"[4] | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 4"[4] | D. HOT | PEC | |
[1] Colors: Dark Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: None
Final Cure Time and Temperature: 6233 4G/6233W 4G: 40 seconds at 450°F; 6233 8G/6233W
8G: 90 seconds at 450°F; 6233 11G/6233W 11G: 110 seconds at 450°F
Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425° F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400° F
[4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
use.
|
||||
|
Coatings - Pump |
||||
| ScotchKote 134[2] | [4] | D. HOT | PEC | |
| ScotchKote 134W[2] | [4] | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 2"[4] | D. HOT | PEC | |
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425° F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400° F
[4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
use.
|
||||
|
Coatings - Tank |
||||
| ScotchKote 134[2] | >= 5 gal. | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N[3] [4] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] [4] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] [4] | >= 5 gal. | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] [4] | >= 5 gal. | D. HOT | PEC | |
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425° F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400° F
[4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
use.
|
||||
|
Coatings - Valve |
||||
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233 8G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] | >= 1/2" | D. HOT | PEC | |
| 3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] | >= 1/2" | D. HOT | PEC | |
| ScotchKote 134[2] | >= 1/2"[4] | D. HOT | PEC | |
| ScotchKote 134W[2] | >= 1/2"[4] | D. HOT | PEC | |
| Scotchkote 206N[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Extra LG[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Fluid Bed[3] | >= 2"[4] | D. HOT | PEC | |
| Scotchkote 206N Long Gel[3] | >= 2"[4] | D. HOT | PEC | |
[1] Colors: Dark Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: None
Final Cure Time and Temperature: 6233 4G/6233W 4G: 40 seconds at 450°F; 6233 8G/6233W
8G: 90 seconds at 450°F; 6233 11G/6233W 11G: 110 seconds at 450°F
Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 60
Maximum Thinner: None
Final Cure Time and Temperature: 25 minutes at 425° F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 180 seconds at 400° F
[4] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
use.
|
||||
Facility : North Yorkshire, United Kingdom
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| Scotchkote 162PWX[1] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: Blue or gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 40
Final Cure Time and Temperature: 7 days at 20°C
Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior
to being placed into service.
|
||||
|
Coatings - Pipe - Immediate Return to Service |
||||
| 3M Scotchkote Pipe Renewal Liner 2400[2] [3] | >= 4" | CLD 23 | PUA | |
| Scotchkote 162PWX[1] [2] | >= 1" | CLD 23 | EPOXY | |
[1] Colors: Blue or gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 40
Final Cure Time and Temperature: 7 days at 20°C
Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior
to being placed into service.
[2] Evaluated for Immediate Return to Service.
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 473
Maximum Thinner: None
Final Cure Time and Temperature: 1 hour at 3°C (37°F)
Special Comments: Mix ratio of Base:Activator is 1:1 by volume. No disinfection step
required. Flush for 30 minutes at 5 gallons/minute. Certified for dry film thickness
(DFT) of 40-473 mils
|
||||
|
Coatings - Tank |
||||
| Scotchkote 162PWX[1] [2] | >= 100 gal. | CLD 23 | EPOXY | |
[1] Colors: Blue or gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 40
Final Cure Time and Temperature: 7 days at 20°C
Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior
to being placed into service.
[2] Evaluated for Immediate Return to Service.
|
||||
|
Coatings - Valve |
||||
| Scotchkote 162PWX[1] [2] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: Blue or gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 40
Final Cure Time and Temperature: 7 days at 20°C
Special Comments: Mix ratio Part A:B is 2:1 by weight. A 1 hour flush is required prior
to being placed into service.
[2] Evaluated for Immediate Return to Service.
|
||||
NOTE: Only products bearing the NSF Mark are NSF Certified.
Number of matching Manufacturers is 1
Number of matching Products is 113
Processing time was 0 seconds