[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

[1] The M at the end or middle of the part number represents metric.  The A at the beginning
    of each part number represents acetal.  The A is followed by an abbreviation of the
    valve design.  Metric size (mm or mm x in) valves are black; British size (in) valves
    are white. 
    
    Valve design abbreviations: 
    HMC   - Hand valve male connector (NPTF threads) 
    HUC   - Hand valve union connector 
    HUCS  - Hand valve union connector, short handle 
    HFA   - Hand valve female adapter (NPTF threads) 
    HFAUC - Hand valve female adapter (union connector) 
    HVEU  - Hand valve elbow union 
    HWM   - Hand valve washing M/C 
    TWV   - Three-way valve 
    HBC   - Hand barb connector 
    HSV   - Hand valve stop connector 
    THC   - Throttle hand valve connector
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

[1] [XX] represents the inlet diameter size in inches, where [XX] may be any of the
    following: 01 (5/32") , 03 (3/16"), 04 (1/4"), 05 (5/6"), 06 (3/8"), or 07 (1/2").
    For fittings without threads, [YY] represents the outlet diameter size in inches, where
    [YY] may be any of the following: 01 (5/32"), 03 (3/16"), 04 (1/4"), 05 (5/16"), 06
    (3/8"), 07 (1/2"), 08 (5/8"), 09 (3/4"), 10 (7/8"), or 11 (1").
    For fittings with threads, [YY] represents the threaded outlet size in inches, where
    [YY] may be any of the following: 01 (5/32"), 02 (1/8"), 03 (3/16"), 04 (1/4"), 05
    (5/16"), 06 (3/8"), 07 (1/2"), 08 (5/8") , 09 (3/4"), 10 (7/8"), 11 (1"), 7/16 (7/16"),
    or 9/16 (9/16").
    [Z] represents the color of the fitting body, where 'W' represents white and the absence
    of a letter represents gray.  'SW' represents a silicone o-ring with a white fitting
    body.
[2] Fitting configuration abbreviations:
    BBC    - Barb connector
    BFU    - Both female union, BSP thread
    BU     - Bulkhead union
    C      - Cap
    CIBEU  - Clean elbow union (both (double) o-ring)
    CIBUC  - Clean union connector (both (double) o-ring)
    CIMCBT - Clean male connector, BSPT thread
    CIMCF  - Clean male connector, threaded cap
    CIMCW  - Clean male connector, BSW thread
    CR     - Cross
    DA     - Drain adapter
    DEU    - Dispensing elbow union
    EL     - Enlarger
    EU     - Elbow union
    FA     - Femal adapter, NPTF-Standard type
    FAU    - Female adapter, UNS thread
    FAUF   - Female adapter, UNF thread
    FAUN   - Female adapter, UN thread
    FC     - Filter connector
    FR     - Fitting reducer
    HA     - Hub adapter
    KFA    - Kitchen faucet adapter
    MC     - Male connector
    MCB    - Male connector, BSP thread
    MCBB   - Male connector with Big O-ring
    MCBT   - Male connector, BSPT thread
    MCF    - Male connector, MFL thread (threaded cap)
    MCW    - Male connector, BSW thread
    ME     - Male elbow
    MTU    - Male tee union (NPTF thread)
    OC     - Offset connector
    PBBC   - Power barb connector
    PBEU   - Power elbow union (both (double) o-ring)
    PBUC   - Power union connector (both (dobule) o-ring)
    PL     - Plug
    PMCBT  - Power male connector, BSPT thread
    PMCF   - Power male connector, threaded cap
    PMCW   - Power male connector, BSW thread
    PSEU   - Power elbow union (single o-ring)
    PSFBU  - Power flow bend union (single o-ring)
    PSUC   - Power union connector (single o-ring)
    RD     - Reducer
    SA     - Stem adapter
    SAB    - Stem adapter, BSP thread
    SABT   - Stem adapter, BSPT thread
    SAW    - Stem adapter, BSW thread
    SEU    - Swivel elbow union
    SUC    - Swivel union connector
    SVA    - Stop valve adapter
    TBC    - Tube barb connector
    TEB    - Tube elbow barb connector
    TES    - Tube end stop
    TEU    - Tube elbow union
    THWD   - Three-way divider
    TTU    - Tee union (4 holes)
    TU     - Tee union (3 holes)
    TWD    - Two-way divider
    UB     - U-Bend
    UC     - Union connector
[3] [XX] represents the outer diameter of the inlet in mm, where XX may be 04 (4 mm) - 28
    (28 mm).
    [YY] represemts the outer diamter of outlet in mm for fittings without threads, where YY
    may be 04 (4 mm) - 28 (28 mm).
    [YY] represent the outer diameter of the threded outlet in inches for threaded fittings,
    where YY may be 02 (1/8"), 04 (1/4"), 06 (3/8"), 07 (1/2"), 08 (5/8"), 09 (3/4"), 11
    (1"), 7/16 (7/16"), or 9/16 (9/16").
[4] Fitting configuration abbreviations:
    BBC  - Barb connector
    BU   - Bulkhead union
    C    - Cap
    CR   - Cross
    DA   - Drain adapter
    EL   - Enlarger
    EU   - Elbow union
    FA   - Female adapter, NPTF standard type
    FAU  - Female adapter, UNS thread
    FAUF - Female adapter, UNF thread
    FAUN - Female adapter, UN thread
    FWC  - Four way connector
    HA   - Hub adapter
    MC   - Male connector
    MCB  - Male connector, BSP thread
    ME   - Male elbow
    OC   - Offset connector
    PBEU - Power elbow union (both (double) o-ring)
    PBUC - Power union connector (both (double) o-ring)
    PL   - Plug
    PMCF - Power male connector, threaded cap
    PMCW - Power male connector, BSW thread
    PSUC - Power union connector (single o-ring)
    RD   - Reducer
    SA   - Stem adapter
    SAB  - Stem adapter, BSP thread
    SEU  - Swivel elbow union
    SSA  - Stem-to-Stem adapter
    SUC  - Swivel union connector
    TBC  - Tube barb connector
    TC   - Tank connector
    TES  - Tube end stop
    THWD - Three-way divider
    TU   - Tee union
    TWD  - Two-way divider
    UB   - U-Bend
    UC   - Union connector
[5] 15 mm x 1/2" - 22 mm x 3/4"
[6] 15 mm x 1/2" - 18 mm x 1/2"
[7] 15 mm x 3/8" - 15 mm x 1/2"
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
[10] [XX] represents the inlet diameter size in inches, where [XX] may be any of the
     following: 04 (1/4"), 05 (5/16"), 06 (3/8"), 07 (1/2"), 047 (1/4"), or 067 (3/8").
     For fittings without threads, [YY] represents the outlet diameter size in inches, where
     [YY] may be any of the following: 04 (1/4"), 05 (5/16"), 06 (3/8"), or 07 (1/2").
     For fittings with threads, [YY] represents the threaded outlet size in inches, where
     [YY] may be any of the following: 02 (1/8"), 03 (3/16"), 04 (1/4"), 05 (5/16"), 06
     (3/8"), 07 (1/2"), or 16C (7/16" - 24").

[8] DPE - Trade name
    OD - Outer diameter
         01 - 5/32"
         03 - 3/16"
         04 - 1/4"
         05 - 5/16"
         06 - 3/8"
         07 - 1/2"
         04M - 4mm
         06M - 6mm
         08M - 8mm
         10M - 10mm
         12M - 12mm
         15M - 15mm
    CO - Color
         BK  - Black
         BL  - Blue
         GN  - Green
         GR  - Gray     
         IBK - Black
         NA  - Natural
         OR  - Orange
         RE  - Red
         WT  - White
         YE  - Yellow
    RL - Reel length (meters)
         0100 - 100 m
         0150 - 150 m
         0200 - 200 m
         0300 - 300 m
         0400 - 400 m
         0500 - 500 m
         1000 - 1000 m
         1500 - 1500 m
    Certified for the maximum length for each diameter:
    Outer diameter:       Inner diameter:       Length:
    5/16"                 .187"                 7.8 m
    3/8"                  1/4"                  5.8 m
    1/2"                  3/8"                  3.9 m
    8mm                   6mm                   6.2 m
    10mm                  7mm                   5.3 m
    12mm                  9mm                   4.1 m
    15mm                  11.5mm                3.2 m
[9] Certified for blue or white tubing.
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.