These NSF Official Listings are current as of Sunday, February 03, 2013 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://www.nsf.org/Certified/PwsComponents/Listings.asp?Company=38570&Standard=061&


NSF/ANSI STANDARD 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing.  Click here for a list of Abbreviations used in these Listings.

 
Rectorseal Corporation 
2601 Spenwick Drive
Houston, TX 77055 
United States 
713-263-8001
Visit this company's website

Facility : # 1 USA

Joining and Sealing Materials

      Water Water
      Contact Contact
  Trade Designation Size Temp Material

Thread Compounds
  Tru-Blu™[1] [G] >= 1/2" CLD 23 TC
  RectorSeal® T Plus 2®[1] [G] >= 1/2" C. HOT TC
  Pure White Teflon Pipe Compound[1] [3] [G] >= 1/2" C. HOT TC
  RectorSeal® No. 5®[1] [G] >= 1/2" CLD 23 TC 

[1] Products were prepared for evaluation according to manufacturer's instructions.
[3] DuPont Registered Trademark.
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Solvent Cements
  Sam™ CL-3[2] [G] >= 1/2" C. HOT CLE
  Sam™ CL-3L - Low VOC[2] [G] >= 1/2" C. HOT CLE 

[2] This product is a cleaner that is intended to be used directly before application of a
    solvent cement.  An additional primer is not required.
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Fluxes
  NOKORODE® Regular Paste Flux[G] >= 1/2" C. HOT FLX
  NOKORODE® Aqua-Flux™[G] >= 1/2" C. HOT FLX 

[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.


Facility : # 2 USA

Joining and Sealing Materials

      Water Water
      Contact Contact
  Trade Designation Size Temp Material

Patching Materials [G]
  RectorSeal EP200 Epoxy Putty [1] C. HOT EPOXY
  RectorSeal EP400 Epoxy Putty [1] C. HOT EPOXY 

[1] Certified for a maximum surface area to volume ratio not to exceed 0.3 sq. in./L in pipe
    or 1% of a 20,000 gallon tank.
[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.


Facility : # 3 USA

Joining and Sealing Materials

      Water Water
      Contact Contact
  Trade Designation Size Temp Material

Lubricants[G]
  RectorSeal® Pipe Lube >= 1/2" CLD 23 LUB 

[G] Product also Certified to NSF/ANSI 61, Annex G and is in compliance with California's 
    Health & Safety Code Section 116875 (commonly known as AB1953) and Vermont Act 193.
    Weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.

Number of matching Manufacturers is 1
Number of matching Products is 11
Processing time was 0 seconds