+ Material complies with NSF/ANSI Standard 61 health effects requirements.
[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[1] Certified for a minimum daily flow of 250,000 gallons/day.

[1] Certified for a level not to exceed 15 fl. oz per 100 pounds of cement.  Certified for
    use in pipes 6" and greater, tanks 200 gallons and greater.

[1] Certification includes exposure to a minimum surface temperature of 120° F for a minimum
    of 24 cumulative hours, after flashing has been completed.
[2] Components are Certified only when used per manufacturer's instructions in an
    installation of the Carlisle Sure-Seal Geomembrane System in a tank greater than or
    equal to 250,000 gallons.

[1] Copper tube (Alloy C12200) is Certified by NSF to NSF/ANSI 61 for use in drinking water
    supplies of pH 6.5 and above.  Drinking water supplies that are less than pH 6.5 may
    require corrosion control to limit leaching of copper into the drinking water.
[2] This product has not been evaluated for use in water main transmission piping but has
    been evaluated for use as water distribution piping in buildings.
[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[1] Only installations exhibiting the NSF Mark are Certified by NSF International.
[2] Listed Storage Tanks/Reservoirs include galvanized appurtenances; polyurethane (or
    alternate rubber) sealer, polyethlene, polypropylene, or polyphenylene oxide fastener
    coverings; buna-N rubber gaskets; and magnesium or zinc anodes.  Interiors and floors
    can be composed of: Vitreous coated interior with vitreous coated floor or concrete
    floor coated with NSF Certified coating, or Epoxy coated interior with epoxy coated
    floor or concrete floor coated with NSF Certified coating, or stainless steel interior
    with stainless steel floor or concrete floor coated with NSF Certified coating.  All
    NSF-Certified coatings must be Listed for tanks at least 17,650 gallons, and application
    must occur according to Certified specifications.
[3] Tank capacity

[1] Certified for a minimum daily flow of 272,520 L.

[1] All sizes and gradations

[1] Certification includes lubricant, form oil, joint rings, patch compound, and stencil
    ink. Gaskets used with this system must be NSF Certified for the applicable diameter
    pipe size.

[1] Certification includes lubricant, form oil, joint rings, patch compound, and stencil
    ink. Gaskets used with this system must be NSF Certified for the applicable diameter
    pipe size.

[1] Certified for >= 200 gallon tanks, >= 6" pipe.  This product may be used at a maximum
    use level of 80% as a replacement for Portland Cement.
[2] All Listed products from this facility are NSF Certified, whether or not they bear the
    NSF Mark.

[1] Certified for a minimum flow rate of 1,440 gallons/day/square foot.

[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[1] Certified for use at a maximum surface area to volume ratio of 0.0005 sq. in./L in a
    tank.
[2] Only products bearing the NSF Mark are Certified.

[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[1] Certified for pipes 4" and greater, tanks 200 gallons and greater.  Maximum use level of
    admixture is 100% of cement by mass.

[1] All Listed products from this facility are NSF Certified, whether or not they bear the
    NSF Mark.
[2] Certified for pipes 4" and greater, tanks 200 gallons and greater.

[1] Certified for the following mesh sizes: 8 x 20, 20 x 40.

[1] Restricted to a maximum use level of 50 sq. in./L.
[2] Restricted to a maximum use level of 80 sq. in./L.

[1] Product Certification does not include use of a primer.
[2] Certified for a maximum of 54 1/2" joints per residence (5 joints per Liter).

[1] Number of Coats:  1
    Maximum Field Use Dry Film Thickness (in mils):  20-30
    Recoat/Cure Time:  24 hours

[1] Certified for a maximum exposed surface area of 2.2 sq. in./1000 gal.
[2] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.
[3] Certified for a maximum exposed surface area of 22 sq. in./1000 gal.

[2] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.

[1] Colors: Gray, white
    Number of Coats: 2
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure Time and Temperature: 7 days at 75°F
    Special Comments: Apply to concrete at a rate of 0.25 lb. mixed slurry per square foot.
    

[G] Product also Certified to NSF/ANSI Standard 61, Annex G (weighted average lead
    content of <=0.25%) and is in compliance with California's Health & Safety Code
    Section 116875 (commonly known as AB1953).

[1] Number of Coats: Layer 1: Procor Concrete Sealant 
                     Layer 2: Procor 75 Fluid Applied Waterproofing System
    Maximum Field Use Dry Film Thickness (in mils): 60-70
    Recoat Cure Time and Temperature: 3 hours @ 75°F
    Final Cure Time and Temperature: 48 hours @ 75°F

[1] Certified for a maximum use level of 8 fluid oz. per 100 lbs. of cement.
[2] Certified for use in pipes 4" and greater and in tanks 200 gallons and greater.
[4] All Listed products from this facility are NSF Certified, whether or not they bear the
    NSF Mark.

[2] Certified for use in pipes 4" and greater and in tanks 200 gallons and greater.
[3] Certified for a maximum use level of 600 grams liquid grinding aid per 1000 kilograms of
    cement.
[4] All Listed products from this facility are NSF Certified, whether or not they bear the
    NSF Mark.