Residential Drinking Water Treatment Protocols
- Military Operations
- Water Purifiers
- Iodine Reduction
We have the unique ability to develop new protocols for testing and certification based on our customer’s needs. Much like traditional NSF standards, protocols are developed through a collaborative process involving a technical panel, including the product manufacturer, regulators, academicians, end users and public health experts with relevant expertise. Unlike NSF standards, however, the development phase is confidential, protecting your proprietary interests.
By creating customized testing criteria and validating performance and product claims, we provide assurance of product performance to your customers in your desired markets.
NSF P477: Drinking Water Treatment Units – Microcystin
NSF P477 includes requirements for verifying that point-of-use (POU) water filters can effectively reduce microcystins (toxins produced by blue-green algae) in drinking water. These requirements include precisely testing these filters throughout and beyond the manufacturer’s recommended treatment capacity with actual microcystins at levels representing some of the highest seen in drinking water, for reduction down to the 0.3 ppb (parts per billion) level recommended by the U.S. EPA for children under 6 years of age.
NSF P248: Military Operations Microbiological Water Purifiers
NSF P248 evaluates individual small water purifiers (SWPs) to determine their effectiveness in providing microbiological purification to water from any fresh water source. SWPs tested using this protocol are intended for individual or squad-size use for emergency or short-term planned missions. This protocol does not test or verify claims of chemical contaminant removal efficiencies.
NSF P231: Microbiological Water Purifiers
NSF P231 establishes minimum requirements for health and sanitation characteristics of microbiological water purifiers. The requirements are based on the recommendations of the U.S. Environmental Protection Agency's Task Force Report, Guide Standard and Protocol for Testing Microbiological Water Purifiers (1987) (Annex B).
NSF/JWPA P72: Iodine Radioisotope Reduction
NSF/JWPA P72 was developed by NSF International and the Japan Water Purifier Association (JWPA) to effectively evaluate point-of-use drinking water treatment units to ensure that they reduce all common forms of iodine in drinking water.
- 4 months ago
飲用水中的新生污染物引起民眾對健康的關注-美通社PR-Newswire HONG KONG — While replacing lead service lines and old fixtures may be desirable, it isn't always possible, especially...
- 10 months ago
ANN ARBOR, Mich. – Global public health organization NSF International has appointed Tina Yerkes, Ph.D., to General Manager of Filtration...
- 1 year ago
ANN ARBOR, Mich. – A vast majority (82 percent) of consumers report they are concerned about trace levels of emerging...
How do I choose between certification to NSF P231: Microbiological Water Purifiers and NSF P248: Military Operations Microbiological Water Purifiers?
A discussion about your market would help with this decision. More importantly, P248 was based on the EPA Guide Standard, while P231 uses it in its entirety, unaltered. As such, the protocols have much testing similarity and the government reviewing agency (the U.S. Army Public Health Command) has agreed that for those manufacturers with both a commercial and military market, where it is possible to write a hybrid protocol without compromising the intent of P248, it will allow and will review the PSTPs.
Should I seek full NSF certification or NSF P248, Appendix B?
The answer lies with your market. If you are solely targeting the military, NSF P248, Appendix B is the data that the government reviewing agency (GRA) requires for receiving its Government Reviewing Agency Letter of Compliance. The GRA will do a separate review of the wetted materials in the product, but it does not require full NSF certification. If your market is commercial or a mix of commercial and military, NSF certification may be needed. Full certification includes the steps necessary to receive the GRA P248 Letter of Compliance as the military reviews all purifier specific test plans (PSTPs) as well as material safety, structural integrity, auditing, literature and labeling under NSF’s certification program. If a product is NSF certified, the GRA will not have to perform an additional materials review as the NSF evaluation is recognized as at least as protective.
Why does the NSF P248 protocol require two sequential challenges for microbiological challenging?
Some test-required organisms are not compatible for combining due to method issues or organism competition. Examples found in NSF P248 are MS2 and fr, which should not be combined. It is important to consider not only if one organism will outcompete the other, but also if the stock of an organism contains a preservative, etc. that may inhibit the growth of a mixed organism. Sequentially challenging allows for the same unit to see all organisms, but eliminates the concerns associated with organisms that cannot be combined. An important test consideration with sequential challenging is to be certain to undergo the 10 void volume ‘seeding’ of each organism or organism pairing prior to challenging for sample collection. Seeding was included in the EPA Guide Standard and included in NSF P248 to ensure that there is no dilution of challenge water with the un-microbiologically challenged water that was left in the system. Seeding during serially challenging also ensures that the previous organism(s) was/were completely displaced prior to the actual sample collection for the next organism(s) sample collection.
Under NSF Protocol P248, why are elevated total organic carbon (TOC) and turbidity required throughout the full challenge test-water phase when testing individual water purifiers (IWPs), but only during seeding and sampling points in the challenge test-water phase when testing small unit water purifiers (SUWPs)?
During military operations, IWPs are used for emergency or short-term missions where water selection may be limited. The design of many IWPs allows, and intends, for very shallow surface water sources, such as a puddle, to be accessed as drinking water. If an IWP is used with a larger body of water, the typical design allows filling the bladder or an on-demand filter (such as a straw) with water that is most likely near the more shallow areas and, thus, likely to be more turbid and contain more TOC than water on the surface of the deeper parts of the body of water. Therefore, requiring the full challenge test-water throughout provides a realistic worst case test. SUWPs, with the higher draw and flow, are designed to make use of larger bodies of available surface water, such as ponds or lakes. Typically the intake hose will allow for use of water that is deeper than the immediate shallow shoreline. Additionally, missions requiring SUWPs are expected to have more latitude in source water selection, including seeking out the cleanest source available. For these reasons, it was decided that requiring elevated TOC and turbidity only at the seeding and sampling points, but also including a ‘clogging’ point, will sufficiently challenge the systems to document capabilities under realistic conditions.
Why does an individual water purifier (IWP) have a set test capacity (135 L) while the small unit water purifier (SUWP) has a daily operation period (four hours)?
By definition, IWPs supply needed water to a single individual. It has been identified that the volume needed for an individual is 15 L/day. Although the actual capacity of most systems varies with the quality of the source water, IWPs must meet the rigorous waters and test capacity of 135 L for NSF Protocol P248 so that the soldiers can be sufficiently equipped with IWPs to complete a mission. SUWPs have varying production rates and can service varying numbers of soldiers, with system selection based on mission needs. It was not practical to create test plans for an SUWP to serve a specific number of soldiers. Depending on the mission, all may have a place in the field. Defining a test capacity for an SUWP would result in excluding systems that may be valuable but not at the scale of production to meet the test or in greatly understating or not sufficiently challenging the capacity of a larger flowing/capacity system. The solution was to have an expectation on the daily production as flowing time. This would provide valuable information about the capacity and performance at that capacity for equipping decisions when choosing a system. The test capacity for an SUWP is the product water volume accumulated when flowing for four hours per day for ten flowing days. Due to varying system sizes and flow rates, four hours provides a test volume sufficient to evaluate system capabilities without benefitting any single-size system.
Why is seeding necessary for testing against NSF Protocol P248?
A system holds water after flow has stopped, which the protocol refers to as void volume. When microbiologically spiked water is introduced into the system, this void volume, which does not have any microbiological addition, causes a dilution of the microbiologically challenged water being introduced. This void volume, therefore, must be displaced before it can be assured that the microbiological challenge exposed to the system equals that of the targeted influent concentration. If this is not done, the performance may be overstated. The EPA Guide Standard identifies 10 void volumes (vv) as appropriate for seeding. For batch systems, a full batch (as long as 10 vv is achieved) is used for ease of testing.
What is radioactive iodine?
Radioactive iodine (I-131) is produced by the fission of uranium atoms during the operation of nuclear reactors. Iodine is a solid substance that can go directly from a solid to a gas, without first becoming liquid. This vapor is irritating to the eyes, nose and throat. Radioactive iodine products form within fuel rods. Reactor chemistry must be carefully controlled, to avoid rapid build-up and increased pressure that may cause corrosion, cracks or other breaches in the rods.
Why was NSF/JWPA Protocol P72 developed?
NSF International and the Japan Water Purification Agency (JWPA) began developing P72: DTWU - Iodine Radioisotope Reduction at the request of water treatment systems manufacturers following the tragic earthquake in Japan in March 2011, to help solve consumer confusion and provide a means to evaluate drinking water systems that reduce radioactive iodine. Manufacturers felt water systems certified to the protocol would provide consumers additional reassurance. The protocol was developed by a team of industry experts, including representatives from JWPA and the U.S. Army, as well as scientists at NSF International, to validate the performance claims of point of use (POU) drinking water treatment units (DWTU) to effectively remove all common forms of iodine from drinking water.