Plastic Piping, Fittings, Material and Ingredients Testing and Certification
April 17, 2025
Manufacturers of plastic pipes, fittings, materials and ingredients trust us to assist them with all necessary testing, inspection, and certification.
Let us support your compliance efforts if your product is used in drinking water, drain waste & vent, gas, fire safety, geothermal, or electrical conduit applications. Below is a list of some key standards for which we offer testing and certification services in this segment.
Contact us using the form below if you’re interested in testing or certification to a specific standard listed, or for a custom project.
| Standard/Service name | Description |
| AASHTO M252 | Standard Specification for Corrugated Polyethylene Pipe, 75–250 mm (3–10 in.) Diameter |
| AASHTO M294 | Standard Specification for Corrugated Polyethylene Pipe, 300–1500 mm (12–60 in.) Diameter |
| AASHTO M304 | Standard Specification for Polyvinyl Chloride (PVC) Profile Wall Drainpipe and Fittings Based on Controlled Inside Diameter |
| AASHTO M330 | Standard Specification for Polypropylene Pipe, 300–1500 mm (12–60 in.) Diameter |
| ACS | Attestation de Conformité Sanitaire (France) |
| ANSI/ASSE 1050 | Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems |
| ANSI/ASSE 1051 | Performance Requirements for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems |
| ASME A112.14.1 (R2017) | Backwater Valves |
| ASTM 2136 | Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe |
| ASTM B858 (R2018) | Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys |
| ASTM D1084 | Standard Test Methods for Viscosity of Adhesives |
| ASTM D1149 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
| ASTM D1238 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D1243 | Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers |
| ASTM D1414 | Standard Test Methods for Rubber O-Rings |
| ASTM D1505 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D1598 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D1599 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D1600 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D1693 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D1755 | Standard Specification for Poly(Vinyl Chloride) Resins |
| ASTM D1784 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
| ASTM D1785 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
| ASTM D2122 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D2152 | Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion |
| ASTM D2235 | Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings |
| ASTM D2239 | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
| ASTM D2240 | Test Method for Rubber Property—Durometer Hardness |
| ASTM D2241 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
| ASTM D2290 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM D2412 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D2444 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings using a Tup (Falling Weight) |
| ASTM D2464 | Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D2466 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
| ASTM D2467 | Specification for Socket-Type Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D2513 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D256 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
| ASTM D2564 | Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems |
| ASTM D2583 | Indentation Hardness of Rigid Plastics using a Barcol Impressor |
| ASTM D2584 | Ignition Loss of Cured Reinforced Resins |
| ASTM D2609 | Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe |
| ASTM D2657 | Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings |
| ASTM D2661 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D2665 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D2672 | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
| ASTM D2683 | Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing |
| ASTM D2729 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM D2737 | Standard Specification for Polyethylene (PE) Plastic Tubing |
| ASTM D2765 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D2837 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D2839 | Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene |
| ASTM D2846/D2846M | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems |
| ASTM D2852 | Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings |
| ASTM D2855 | Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets |
| ASTM D2863 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D2949 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D2990 | Flexural and Tensile Creep (50-year dry creep factor) |
| ASTM D2992 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM D2996 | Standard Specification for Filament-Wound Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D2997 | Standard Specification for Centrifugally Cast Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D3034 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM D3035 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D3122 | Standard Specification for Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings |
| ASTM D3132 | Standard Test Method for Solubility Range of Resins and Polymers |
| ASTM D3138 | Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components |
| ASTM D3139 | Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals |
| ASTM D3212 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
| ASTM D3222 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding, Extrusion, and Coating Materials |
| ASTM D3261 | Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing |
| ASTM D3311 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D3350 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D3418 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D3517 | Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe |
| ASTM D3567 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D3681 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM D3835 | Standard Test Method for Determination of Properties of Polymeric Materials using a Capillary Rheometer |
| ASTM D3895 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
| ASTM D395 | Standard Test Methods for Rubber Property—Compression Set |
| ASTM D3965 | Standard Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings |
| ASTM D4000 | Standard Classification System for Specifying Plastic Materials |
| ASTM D4066:13 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D4101 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D412 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension |
| ASTM D4161:14 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals |
| ASTM D4218 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique |
| ASTM D4396 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications |
| ASTM D5365 | Standard Test Method for Long-Term Ring-Bending Strain of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D542 | Standard Test Method for Index of Refraction of Transparent Organic Plastics |
| ASTM D543 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D5630 | Standard Test Method for Ash Content in Plastics |
| ASTM D570 | Standard Test Method for Water Absorption of Plastics |
| ASTM D5813 | CIPP chemical resistance, Strain Corrosion (Qualification testing) |
| ASTM D5927 | Standard Specification for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods |
| ASTM D638 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D6394 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D695 | Standard Test Method for Compressive Properties of Rigid Plastics |
| ASTM D790 | Flexural Properties (all trenchless products) |
| ASTM F1055 | Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing |
| ASTM F1057 | Standard Practice for Estimating the Quality of Extruded Poly (Vinyl Chloride) (PVC) Pipe by the Heat Reversion Technique |
| ASTM F1216 | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube |
| ASTM F1281 | Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe |
| ASTM F1282 | Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe |
| ASTM F1336 | Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings |
| ASTM F1412 | Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
| ASTM F1473 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM F1483 | Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe |
| ASTM F1488 | Coextruded Composite Pipe |
| ASTM F1498 | Standard Specification for Taper Pipe Threads 60deg for Thermoplastic Pipe and Fittings |
| ASTM F1673 | Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
| ASTM F1743 | CIPP chemical resistance (Qualification testing) |
| ASTM F1760 | Coextruded PVC Non-Pressure Pipe Having Reprocessed-Recycled Content |
| ASTM F1807 | Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing |
| ASTM F1866 | Poly (Vinyl Chloride ) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
| ASTM F1924 | Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing |
| ASTM F1960 | Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing |
| ASTM F1970 | Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems |
| ASTM F1974:15 | Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe |
| ASTM F1986 | Standard Specification for Multi-layer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems |
| ASTM F2019 | GRP-CIPP practice (Glass-reinforced - UV cured CIPP product testing) |
| ASTM F2022 (R2019) | Standard Test Method for Performance of Booster Heaters |
| ASTM F2023 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM F2080 | Standard Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe |
| ASTM F2098 | Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings |
| ASTM F2138 | Standard Specification for Excess Flow Valves for Natural Gas Service |
| ASTM F2159 | Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM F2263 | Standard Test Method for Evaluating the Oxidative Resistance of Polyethylene (PE) Pipe to Chlorinated Water |
| ASTM F2306/F2306M | Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM F2389 | Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems |
| ASTM F2390 | Standard Specifications for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycled Content |
| ASTM F2434 | Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing |
| ASTM F2618 | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Pipe Fittings for Chemical Waste Drainage Systems |
| ASTM F2619 | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM F2620 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F2623 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing |
| ASTM F2648/F2648M | Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications Except for: Section 7.8 |
| ASTM F2735 | Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM F2764/F2764M | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM F2769 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems |
| ASTM F2788/F2788M | Standard Specification for Metric-Sized Crosslinked Polyethylene (PEX) Pipe |
| ASTM F2806 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR) |
| ASTM F2854 | Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing |
| ASTM F2855 | Standard Specification for Chlorinated Poly(Vinyl Chloride)/Aluminum/Chlorinated Poly(Vinyl Chloride) (CPVC-AL-CPVC) Composite Pressure Tubing |
| ASTM F2881:2021e1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F2905/F2905M-2021a | Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings, and Joints For Oil and Gas Producing Applications |
| ASTM F2929 | Standard Specification for Cross-Linked Polyethylene (PEX) Tubing, 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM F2969:12 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) IPS Dimensioned Pressure Pipe |
| ASTM F3128 | This is the standard specification for poly(vinyl chloride) (PVC) schedule 40 drain, waste, and vent pipes with a cellular core. |
| ASTM F3253 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing with Oxygen Barrier for Hot- and Cold-Water Hydronic Distribution Systems |
| ASTM F3347 | Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing |
| ASTM F3348 | Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM F402 | Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings |
| ASTM F409 | Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings |
| ASTM F412 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F437 | Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM F438 | Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 41 |
| ASTM F439 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM F441/F441M | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 |
| ASTM F442/F442M | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR) |
| ASTM F477 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM F480 | Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 |
| ASTM F493 | Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings |
| ASTM F512 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation |
| ASTM F610/F610M | Standard Test Method for Evaluating the Quality of Molded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings by the Heat Reversion Technique |
| ASTM F628 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core |
| ASTM F656 | Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings |
| ASTM F667 | Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings |
| ASTM F679 | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
| ASTM F714 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM F794 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM F876 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing |
| ASTM F877 | Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems |
| ASTM F891 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core |
| ASTM F894 | Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe |
| ASTM F905 | Standard Practice for Qualification of Polyethylene Saddle-Fused Joints |
| ASTM F913 | Standard Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM F949 | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe with a Smooth Interior and Fittings |
| AWWA C900-22 | Minimum manufacturing, verification, and marking requirements for PVC pressure pipe and fabricated fittings, four in. (100 mm) through 60 in. (1,500 mm) |
| AWWA C901 | Polyethylene (PE) Pressure Pipe and Tubing, 1/2 In. (13mm) Through 3 In. (76mm), For Water Service |
| AWWA C904 | PEX Pressure Pipe 1/2” through 3” |
| AWWA C905-10 | Polyvinyl Chloride (PVC) Pressure Pipe & Fabricated Fittings, 14 In Thru 48 In (350 Mm Thru 1,200 Mm) For Water Transmission And Distribution |
| AWWA C906 | Polyethylene (PE) Pressure Pipe and Fittings, 4 In. (100 mm) through 63 in. (1,575mm), for Water Distribution |
| AWWA C907 | Polyvinyl Chloride (PVC) Pressure Fittings for Water-4 In. Through 8 In.. (100 mm Through 200 mm) |
| AWWA C909 | AWWA Standard for Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe, 4 In. Through 24 In. (100 mm through 600 mm), for Water, Wastewater, and Reclaimed Water Service |
| CAN/CSA-C448 SERIES-13 | Design and installation of earth energy systems |
| CSA B137.0 | Definitions, general requirements, and methods of testing for thermoplastic pressure piping |
| CSA B137.1 | Polyethylene (PE) pipe, tubing, and fittings for cold-water pressure services |
| CSA B137.10 | Crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) composite pressure-pipe systems |
| CSA B137.11 | Polypropylene (PP-R & PP-RCT) pipe and fittings for pressure applications |
| CSA B137.18 | Polyethylene of raised temperature resistance (PE-RT) tubing systems for pressure applications |
| CSA B137.19 | Black crosslinked polyethylene (PEX) piping systems for gas services |
| CSA B137.2 | Polyvinyl chloride (PVC) injection-moulded gasketed fittings for pressure applications. |
| CSA B137.3.1 | Molecularly oriented polyvinyl chloride (PVCO) pipe for pressure applications |
| CSA B137.3 | Rigid polyvinyl chloride (PVC) pipe and fittings for pressure applications |
| CSA B137.4.1 | Electrofusion-type polyethylene (PE) fittings for gas services |
| CSA B137.4 | Polyethylene (PE) piping systems for gas services |
| CSA B137.5 | Crosslinked polyethylene (PEX) tubing systems for pressure applications |
| CSA B137.6 | Chlorinated polyvinyl chloride (CPVC) pipe, tubing, and fittings for hot- and cold-water distribution systems |
| CSA B137.9 | Polyethylene/aluminum/polyethylene (PE-AL-PE) composite pressure-pipe systems |
| CSA B181.0 | Definitions, general requirements, and methods of testing for thermoplastic non-pressure piping |
| CSA B181.1 | Thermoplastic Nonpressure Piping Compendium |
| CSA B181.2 | Acrylonitrile-butadiene-styrene (ABS) drain, waste, vent pipe and pipe fittings. |
| CSA B181.3 | Polyolefin and polyvinylidene fluoride (PVDF) laboratory drainage systems |
| CSA B182.1 | Plastic Drain and Sewer Pipe and Pipe Fittings |
| CSA B182.2 | PSM-type polyvinyl chloride (PVC) sewer pipe and fittings |
| CSA C22 No 327 | HDPE conduit, conductors-in-conduit, and fittings |
| CSA-C22.2 No 211.0 | General Requirements and Methods of Testing for Nonmetallic Conduits |
| CSA-C22.2 No 211.1 | Rigid Types EB1 and DB2/ES2 PVC Conduit |
| CSA-C22.2 No 211.2 | Rigid PVC (Unplasticized) Conduit, |
| DIN 8074 | Polyethylene (PE) - Pipes PE 80, PE 100 - Dimensions; Text in German and English |
| DIN 8075 | Polyethylene (PE) - Pipes PE 80, PE 100 - Dimensions; Text in German and English |
| DIN 8077 | Polypropylene (PP) pipes - PP-H, PP-B, PP-R, PP-RCT - Dimensions |
| DIN 8078 | Polypropylene (PP) pipes - PP-H, PP-B, PP-R, PP-RCT - Dimensions |
| FM 1612 | Examination Standard for Polyvinyl Chloride (PVC) Pipe and Fittings for Underground Fire Protection Service |
| FM 1613 | Examination Standard for Polyethylene (PE) Pipe and Fittings for Underground Fire Protection Service |
| Guideline 533 | Ingredients Used in Drinking Water Products |
| IAPMO IGC 321 | Cured-in-Place Point Rehabilitation Systems for Pipe Reconstruction |
| IAPMO IGC 334 | Push Fit Drain, Waste, and Vent (DWV) Fittings |
| IAPMO PS 36 | Lead-Free Sealing Compounds for Threaded Joints |
| IAPMO PS 51 | Expansion Joints and Flexible Expansion Joints for DWV Piping Systems |
| ISO 1167-1 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method |
| ISO 13477 | Thermoplastic pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) |
| ISO 13479 | Polyolefin pipes for the conveyance of fluids - Determination of resistance to crack propagation - Test method for slow crack growth on notched pipes |
| ISO 15874-1 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General |
| ISO 15874-2 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes |
| ISO 2505 | Thermoplastic pipes - Longitudinal reversion - Test method and parameters |
| ISO 3126 | Plastics piping systems - Plastics components - Determination of dimensions |
| ISO 3127 | Thermoplastic pipes- Determination of resistance to external blows- Round-the-clock method |
| ISO 4427-1 | Plastics piping systems for water supply and drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| ISO 4437-2 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| ISO 9080 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastic materials in pipe form by extrapolation |
| NEMA TC-9 | Fittings for PVC Plastic Utilities Duct for Underground Installation |
| NEMA TC-2 | Electrical Polyvinyl Chloride (PVC) Conduit |
| NEMA TC-6 & 8 | PVC Standards Publication TC 6 and 8. Polyvinyl Chloride (PVC) Plastic Utilities Duct for Underground Installations. |
| NEMA TC-7 | Smooth-Wall Coilable Electrical Polyethylene Conduit |
| NSF 489 | Standard Practice to Prevent Contamination in Polyethylene Gas Pressure Pipe |
| NSF P244 | Reduction of bacteria and viruses in devices used as supplemental filtration in emergencies |
| NSF/ANSI 14 | Plastic piping system components and related materials |
| NSF/ANSI 358-1 | Polyethylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems |
| NSF/ANSI 358-2 | Polypropylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems |
| NSF/ANSI 358-3 | Cross-linked polyethylene (PEX) Pipe and Fittings for Water-Based Ground-Source (Geothermal) Heat Pump Systems |
| NSF/ANSI 358-4 | Polyethylene of Raised Temperature (PE-RT) Pipe and Fittings for Water-Based Ground-Source (Geothermal) Heat Pump Systems |
| NSF/ANSI 359 | Valves for Cross-linked Polyethylene (PEX) Water Distribution Tubing Systems |
| PPI TR-3 | Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB), Strength Design Basis (SDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe |
| PPI TR-4 | PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe |
| UBA Conformity Attestation/KTW-BWGL | Hygiene Requirements for Products and Materials in Contact With Drinking Water (Germany) |
| UL 1285 | Pipe and Couplings, Polyvinyl Chloride (PVC), and Oriented Polyvinyl Chloride (PVCO) for Underground Fire Service |
| UL 1821 | Sch 40 and Sch 80 rigid PVC conduit and fittings |
| UL 651 | Schedule 40, 80, Type EB and A Rigid PVC Conduit and Fittings |
| UL 651A | High-Density Polyethylene (HDPE) Conduit |
Interested in testing or certification to a specific standard listed or for a custom project?
Contact us with questions or to receive a quote.
What’s New with NSF
iNADO Partners with NSF to Support Members and Athletes
May 27, 2026iNADO is pleased to welcome NSF’s expertise and experience in support of its members and the athletes they serve
NSF Ends UK’s Three-Year Testing Gap with REG 31 Testing Designation
May 20, 2026NSF’s Oakdale laboratory becomes the UK’s sole facility offering comprehensive BS 6920 and REG 31 testing, closing a critical drinking water safety gap.
Tangent® Materials Announces Industry First: Tangent PolySheet™ CB Earns Certification to NSF 537, Becoming the First PFAS-Free NSF Standard 51 Food Equipment Material
May 20, 2026New food-grade synthetic cutting-board sheet, engineered from the ground up without per- and polyfluoroalkyl substances (PFAS), establishes a new materialsafety benchmark for food-contact and food-equipment applications.
NSF Expands Food Equipment Portfolio with Electrical Safety Testing and Certification
April 30, 2026Manufacturers now have a “one-stop-shop” for both sanitation and electrical safety certification, enabling market expansion and regulatory compliance.